Carefully remove the contents of the shipping carton and check each item on the packing slip before destroying the packing materials . Any damage must be reported to the shipping company . If you do not receive all of the parts, contact Turck at 763-553-7300 .
The part number on the LDT is a record of the characteristics that make up your specific unit . For a translation of the part number, see section 3 .5: Part Number Key . B1407 3 www.turck.com • Phone: 763-553-7300 • Application Support: 1-800-544-7769 • Fax: 763-553-0708 • Turck Minneapolis, MN 55441...
. The diameter of this magnet assembly should not be more than 0 .2" away from the rod . Split magnet assemblies outside of this range will cause signal loss . B1407 5 www.turck.com • Phone: 763-553-7300 • Application Support: 1-800-544-7769 • Fax: 763-553-0708 • Turck Minneapolis, MN 55441...
Page 7
With the EZ-track properly installed inside the hydraulic cylinder, it may be necessary to assemble parts of the hydraulic cylinder . For assistance in this task, refer to the information provided by the cylinder manufacturer . B1407 7 www.turck.com • Phone: 763-553-7300 • Application Support: 1-800-544-7769 • Fax: 763-553-0708 • Turck Minneapolis, MN 55441...
Page 8
3 . This dimension applies when tap drill cannot pass through entire boss . 4 . This dimension does not conform to SAE J1926-1 . 8 B1407 www.turck.com • Phone: 763-553-7300 • Application Support: 1-800-544-7769 • Fax: 763-553-0708 • Turck Minneapolis, MN 55441...
The power supply should be dedicated to the LTX to prevent noise and external loads from affecting it . When powering up more than one LTX on a single power supply, each unit will draw approximately one watt . B1407 9 www.turck.com • Phone: 763-553-7300 • Application Support: 1-800-544-7769 • Fax: 763-553-0708 • Turck Minneapolis, MN 55441...
Page 10
Figure 3-2: Current Sourcing The LTX R10 is current sourcing which allows the current to flow from the EZ-track into the users equipment . 10 B1407 www.turck.com • Phone: 763-553-7300 • Application Support: 1-800-544-7769 • Fax: 763-553-0708 • Turck Minneapolis, MN 55441...
5 . Short the Program Input pin to the Power Supply Common for 4 seconds . Remove the short for 1 second . Within 5 seconds, short the Programming Input pin to the Power Supply +VDC . This completes the programming process . B1407 11 www.turck.com • Phone: 763-553-7300 • Application Support: 1-800-544-7769 • Fax: 763-553-0708 • Turck Minneapolis, MN 55441...
Page 12
8 . Push the Zero button for 4 seconds . Release the Zero button for 1 second . Within 5 seconds, push the Span button . 12 B1407 www.turck.com • Phone: 763-553-7300 • Application Support: 1-800-544-7769 • Fax: 763-553-0708 • Turck Minneapolis, MN 55441...
4 . Using a digital voltmeter, check across Power Supply Common and customer supplied power (+VDC) on the mating end of the cable for a level between 7 and 30 VDC B1407 15 www.turck.com • Phone: 763-553-7300 • Application Support: 1-800-544-7769 • Fax: 763-553-0708 • Turck Minneapolis, MN 55441...
Page 16
. If voltage is between 7 to 30 VDC and the EZ-track is still inoperative, contact factory . * See Section 3 .4 page 13: Specifications for more information on power consumption . 16 B1407 www.turck.com • Phone: 763-553-7300 • Application Support: 1-800-544-7769 • Fax: 763-553-0708 • Turck Minneapolis, MN 55441...