Please do NOT discard the outer shipping carton in the trash. Please recycle whenever possible. CUSTOMER SUPPORT: Contact ADJ Service for any product related service and support needs. Also visit forums.adj.com with questions, comments, or suggestions.
No accessories should be shipped with the product. If any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for loss of or damage to any such accessories, or for the safe return thereof.
This fixture is a sophisticated piece of electronic equipment. To guarantee smooth operation, it is important to follow all instructions and guidelines in this manual. ADJ is not responsible for injury and/or damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual. Only qualified and/or certified personnel should perform installation of this fixture and only the original rigging parts (omega brackets) included with this fixture should be used for installation.
OVERVIEW To select the programming MENU functions To go forward in the DOWN selected functions To go backward in the selected functions ENTER To confirm the selected functions...
D M X S E T U P DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of communication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN”...
Page 9
2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator (ADJ...
SYSTEM MENU To select any functions, press MENU button until the required one is shown on the display. Select the function by pressing the ENTER button. Use DOWN and UP button to change the mode. Once the required mode has been selected, press ENTER button to setup or it will return to the main functions without any change after idling 8 seconds automatically.
Page 11
SYSTEM MENU DMX 512 Address Setting Press the either the MENU, UP, or DOWN buttons until is displayed, press ENTER. The current address will now be displayed and flashing. Press the UP or DOWN buttons to select your desired address. Press ENTER to confirm and exit.
Page 12
SYSTEM MENU Dimmer Mode – This will let you select your desired dimmer curve. Press the MENU button until is displayed, and press ENTER. 1 of 6 dimmer curves will be displayed. “STDA” (standard), “STGE” (stage), “TV” (TV), “ARAL” (Architectural), “THAL” (Theatre) or “STG2”...
Page 13
SYSTEM MENU º. Display Inverse – Reverse the display 180 Select the , press the ENTER button. Use the DOWN and UP button to select (Display Normal) or (Display Inverse). Once selected press ENTER to confirm and exit or exit menu mode without any change after 8 seconds automatically.
BEAM ANGLE ADJUSTMENT To adjust the beam angle, slide the beam angle adjuster located inside/in front of the lens. See diagram below. The beam angle can be adjusted manually, between 7°/11.5°/16°/20.5°/25°. DMX OPERATION DMX Controller No need to turn the unit off when you change the DMX address, as new DMX address setting will be affected at once.
DIMMING CURVE The fixture includes 6 different dimming curve modes that can selected from either the system menu or via DMX. The graph below provides details on each dimming curve mode.
R E M O T E D E V I C E M A N A G E M E N T ( R D M ) NOTE: For RDM to work properly, RDM enabled equipment must be used throughout the entire system, including DMX data splitters and wireless systems.
INSTALLATION The unit should be mounted using a mounting clamp (not provided), affixing it to the mounting bracket that is provided with the unit. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and can support a weight of 10 times the unit’s weight.
MAINTENANCE Cleaning Due to fog residue, smoke and dust, cleaning the internal and external optical lenses and mirror should be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates (I.e. smoke, fog residue, dust, dew). In heavy club use we recommend cleaning on a monthly basis.
AC5PDMX25PRO Pro Series 25’ DMX cable - 5-pin male to 5-pin female connection.* AC5PDMX50PRO Pro Series 50’ DMX cable - 5-pin male to 5-pin female connection.* ADJ plastic color gel sheets 21”x24” Z-PROGEL/SH Light Shaping Filter – 20 degrees 24”x20” sheet...