You may also visit us on the web at www.adj.com for any comments or suggestions. Service Hours are Monday through Friday 8:00 a.m. to 4:30 p.m.
Page 5
During operation the housing may become extremely hot. Avoid touching the unit with bare hands while in use. ADJ Products, LLC will not accept any liability for any resulting damages caused by the non-observance of this manual or any unauthorized modification to this unit.
Page 6
B. The appliance has been exposed to rain or water. C. The appliance does not appear to operate normally or exhibits a marked change in performance. ADJ Products, LLC ww.adj.com PAR Z120/ZP120 RGBW User Instructions Page 6...
To go backward in the selected functions ENTER To confirm the selected functions 4 – Fuse: F 3.15A. 5 – Mains Input/Output :Use powerCON true one mains connection. 6 – DMX Input/Output ADJ Products, LLC ww.adj.com PAR Z120/ZP120 RGBW User Instructions Page 7...
Page 8
XLR connector on either end of the cable. Also remember that DMX Figure 1 cable must be daisy chained and cannot be split.
ADJ Products, LLC ww.adj.com PAR Z120/ZP120 RGBW User Instructions Page 8...
Page 9
2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior.
Page 10
Pin 2 Pin 2 Data True (+signal) Pin 3 Pin 3 Not Used Pin 4 – Do Not Use Not Used Pin 5 – Do Not Use ADJ Products, LLC ww.adj.com PAR Z120/ZP120 RGBW User Instructions Page 10...
Page 11
ENTER button to setup or it will return to the main functions without any change after idling 8 seconds automatically. To go back to the functions without any change press the MENU button. The main functions are shown below: ADJ Products, LLC ww.adj.com PAR Z120/ZP120 RGBW User Instructions Page 11...
• HOLD - If the DMX signal is lost the fixture will stay in the last DMX setting. If power is applied and this mode is set, the unit will automatically go into the last DMX set up. Press ENTER to confirm and exit. ADJ Products, LLC ww.adj.com PAR Z120/ZP120 RGBW User Instructions Page 12...
DOWN and UP button to select the Color Macros 1‐64 or OFF. Press ENTER to confirm and exit, or exit menu mode without any change after 8 seconds automatically. ADJ Products, LLC ww.adj.com PAR Z120/ZP120 RGBW User Instructions Page 13...
Page 14
, press ENTER button and the display will show the version of Select the software of the unit. To go back to the functions press the MENU button. ADJ Products, LLC ww.adj.com PAR Z120/ZP120 RGBW User Instructions Page 14...
To adjust the beam angle slide the beam angle adjuster located inside/in front of the lens. See diagram below. The beam angle can be adjusted manually, between 7°/11.5°/16°/20.5°/25°. ADJ Products, LLC ww.adj.com PAR Z120/ZP120 RGBW User Instructions Page 15...
Page 16
No need to turn the unit off when you change the DMX address, as new DMX address setting will be affected at once. Turn on the unit, under the DMX signal; the LED will display the saved channel address (001‐512). ADJ Products, LLC ww.adj.com PAR Z120/ZP120 RGBW User Instructions Page 16...
0-255 6 Channel Mode Channel Value Function 0-255 Dimmer 0-+100% 0-255 Dimmer 0-+100% 0-255 Dimmer 0-+100% 0-255 Dimmer 0-+100% 0-255 Total Dimmer 0-+100% 0-255 Dimming Fine ADJ Products, LLC ww.adj.com PAR Z120/ZP120 RGBW User Instructions Page 17...
Page 18
Dimmer Dimmer Dimmer Shutter Strobe Effect Slow to Shutter Strobe Pulse Slow to Shutter OPEN (LEDs ON) to Fast Shutter OPEN (LEDs ON) Dimmer Architectural ADJ Products, LLC ww.adj.com PAR Z120/ZP120 RGBW User Instructions Page 18...
Page 19
PAR Z120/ZP120 RGBW Controlling the Unit 9 Channel Mode ADJ Products, LLC ww.adj.com PAR Z120/ZP120 RGBW User Instructions Page 19...
Phillips-head screwdriver to unscrew the fuse holder located above the powerCON input. Remove the bad fuse and replace with a new one, and screw the fuse holder back in. ADJ Products, LLC ww.adj.com PAR Z120/ZP120 RGBW User Instructions Page 20...
Page 21
4. Try to use another DMX controller. 5. Check if the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit. ADJ Products, LLC ww.adj.com PAR Z120/ZP120 RGBW User Instructions Page 21...
May vary depending on several factors including but not limited to:
E nvironmental Conditions, Power/Voltage, Usage Patterns (On-Off Cycling), Control, and Dimming.
ADJ Products, LLC ww.adj.com PAR Z120/ZP120 RGBW User Instructions Page 22...
Page 23
F o r w a r r a n t y s e r v i c e y o u m u s t o b t a i n a R e t u r n A u t h o r i z a t i o n n u m b e r ( R A # ) before sending back the product–please c o n ta c t ADJ Products, LLC Service D e p a r tm e n t at 800-322-6337.