Muse M-1020 KDB, M-1020 KDG - Bluetooth Speaker Manual
  1. Manuals
  2. Brands
  3. Muse Manuals
  4. Speakers
  5. M-1020 KDB
  6. User manual

Muse M-1020 KDB, M-1020 KDG - Bluetooth Speaker Manual

Advertisement

Table of Contents
Contents
Muse M-1020 KDB, M-1020 KDG - Bluetooth Speaker Manual

INSTALLATION

INSTALLATION

  1. Loud Speakers
  2. Base
  3. Screws
  4. Washers

Assembled the wooden base to the main body by the supplied screws and washers.

LOCATION AND DESCRIPTION OF CONTROLS

LOCATION AND DESCRIPTION OF CONTROLS
Please read the instruction carefully before operating the unit.

MAIN UNIT

  1. Indicator
  2. AUX input jack
  3. PAIR button
  4. SOURCE button
  5. Standby Button
  1. Play/Pause Button
  2. VOL- Button
  3. VOL+ Button
  4. Button
  5. Button

UNPACK YOUR UNIT

When you unpack your new unit, make sure that you have removed all the accessories and information papers:

  • Speaker tower
  • AC adaptor
  • User manual
  • Aux in cable (3.5mm) x 1
  • 2 pieces of Assembly screws / washers
  • Wired Microphone x 1

POWER SUPPLY

USING THE AC ADAPTOR

  • The supplied AC adaptor operates on AC mains supplies of 100-240V 50/60Hz and should only be connected to a mains supply within these parameters.
  • Use the supplied AC adaptor only. Using any other AC adaptor could damage the unit.

  • The included AC adaptor is for use with this unit only. Do not use it with other equipments.
  • When the unit is not going to be used for long time, disconnect the AC adaptor from the AC outlet.
  • Be sure to use it near the wall outlet. If a malfunction occurs, disconnect the plug from the wall outlet at once.
  • When the AC adaptor is plugged in, the apparatus is not completely disconnected from the main power source, even when the unit is turned off.
  • AC adaptor is used as the disconnect device. It shall remain readily operable and should not be obstructed during intended use. To be completely disconnected the apparatus from supply mains, the AC adaptor of the apparatus shall be disconnected from the mains socket outlet completely.

GENERAL OPERATION

  1. Press button to turn on or turn off the unit.
  2. Press the SOURCE button to select AUX or Bluetooth playback as desired. The corresponding color of indicator light will be displayed.
    Mode Flashing Solid Light Color
    Standby / Standby Red
    AUX / Playback / No connect Purple
    Bluetooth No connect / Pairing Pause / Playback Blue
  1. Press the VOL+/- Buttons to adjust volume level.
    Note: If no source is played, the unit will go to standby mode automatically after 2 hours.

LISTENING TO AUXILIARY SOURCE

  1. Connect your auxiliary source (e.g. iPod / iPad / MP3 player) to the AUX jack (3.5mm ).
  2. Press the button to turn on the unit. Press the SOURCE button to select Auxiliary mode, purple light will be shown.
  3. Start playback from your auxiliary source.
  4. Adjust the volume to desired level.
  5. To stop playback, disconnect your auxiliary source from the AUX jack.

BLUETOOTH PAIRING & LINKING OPERATION

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by New One S.A.S is under license. Other trademarks and trade names are those of their respective owners.

Pairing a Bluetooth Device

  1. When the unit is ON, press SOURCE button repeatedly select Bluetooth mode. The indicator will blink blue indicating it is in Pairing mode.
  2. On the Bluetooth device, enable Bluetooth and select "M-1020KD" from the Device List. (Refer to the user manual of the device to be connected for detailed operations.) If the Bluetooth device prompts for a pass code, use "0000". Some Bluetooth devices will ask you to accept the connection. You will hear an indication sound when pairing is successful.

Tip: If you want to connect your Bluetooth speaker to another Bluetooth audio device, you need to disconnect current device first and follow the steps above to make a new connection.
If the pairing fails, perform the following:
Press PAIR button the indicator blink blue to enter the Pairing mode. On the Bluetooth device, enable Bluetooth and select "M-1020KD" from the Device List (see step 2 above).

  • On some devices such as computers, once paired you must select the unit from the Bluetooth menu and choose "Use as Audio Device (stereo)" or similar.
  • Pairing remains intact when the unit and/or your Bluetooth device is taken out of communication range. An active connection will be re-established when your Bluetooth device returns within range.
  • When the unit is turned on again, it will automatically try to reconnect with the most recently paired Bluetooth device.

Using a Bluetooth Device

  1. With a unit paired (see previous section), operate your Bluetooth device and its sound will be heard through the M-1020KD's speakers.
  2. Press the button to pause playback. Press again to resume playback.
  3. Select desired track with /.
  4. Adjust the volume using the volume buttons. You can also adjust the volume on the device to which you are paired.

Hereby, NEW ONE S.A.S, declares that this MUSE M-1020 KDB/ M-1020 KDG is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. The declaration of conformity may be consulted at www.muse-europe.com

SING-A-LONG FUNCTION

Sing along with the music by plugging the provided microphone into the microphone jack on the unit.
WARNING: Tapping or dropping the microphone can permanently damage your microphone. Resist the urge to swing the microphone around by the cord.

TROUBLESHOOTING GUIDE

Symptom Cause Solution
No power AC adaptor not plugged into wall outlet. Plug it to the wall outlet properly.
The unit is in Standby mode. Press button to turn on the unit.
No sound Volume in minimum. Adjust volume to a desired level.
The connected device is not in playback mode. Play the music in the connected device.
Sound output of the connected device weak. (AUX IN & BLUETOOTH mode) Adjust volume of connected device.
Sound distortion Volume level too high Reduce the volume level by press the VOL- button.
Volume level of the connected device too high. (AUX IN & BLUETOOTH mode) Reduce the volume level of the connected device.
Bluetooth reception failure Not in the Bluetooth mode. Try to do connection again.

  • Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
  • Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
  • Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
  • Only use attachments / accessories specified by the manufacturer.
  • Unplug this apparatus during lightning storms or when unused for long periods of time.
  • An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
  • Do not overload wall outlets and extension cords as this can result in a risk or fire or electric shock.
  • When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part. Unauthorized substitutions may resu in fire or electric shock or other hazards.

TECHNICAL SPECIFICATION

GENERAL
POWER SUPPLY: DC 9V 1.5A
Consumption: 15W

BLUETOOTH
Bluetooth Version: V4.1
Bluetooth: 2.402-2.48GHz
RF Output Power: -6-+4 dBm
Working Distance: Up to 10 meters measured in open space (wall and structures may affect range of device)
Specifications are subject to change without notice.

SAFETY INSTRUCTION


ATTENTION: To reduce the risk of electric shock, do not remove the cover or back. There are no user serviceable parts inside the unit. Refer all servicing to qualified personnel.
shock hazardThe lightning flash with arrowhead symbol within the triangle is a warning sign alerting the user of "dangerous voltage" inside the unit.
cautionThe exclamation point within the triangle is a warning sign alerting the user of important instructions accompanying the product.

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

If at any time in the future you should need to dispose of this product please note that Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. (Waste Electrical and Electronic Equipment Directive)
NEW ONE S.A.S
10, Rue de la Mission, 25480 Ecole Valentin, France

Documents / Resources

References

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Muse M-1020 KDB, M-1020 KDG - Bluetooth Speaker Manual

Advertisement

Need help?

Need help?

Do you have a question about the M-1020 KDB and is the answer not in the manual?

Questions and answers

Related Manuals for Muse M-1020 KDB

Save Article as PDF

Table of Contents