Muse M-1050 BT Manual

UNPACK YOUR UNIT

When you unpack your new unit, make sure that you have removed all the accessories and information papers:

• Speaker tower
• AC adaptor
• User manual
• 1 piece of Stereo audio connection cable with 3.5 stereo plug
• 2 pieces of Assembly screws / washers

INSTALLATION

1. Loud Speakers
2. Base
3. Screws
4. Washers
5. Speaker Net

Assembled the wooden base to the main body by the supplied screws and washers. The speaker net can be taken out and reassembled.

LOCATION AND DESCRIPTION OF CONTROLS

MAIN UNIT

POWER SUPPLY

USING THE AC ADAPTOR

• The supplied AC adaptor operates on AC mains supplies of 100-240V 50/60Hz and should only be connected to a mains supply within these parameters.
• Use the supplied AC adaptor only. Using any other AC adaptor could damage the unit.

• The included AC adaptor is for use with this unit only. Do not use it with other equipments.
• When the unit is not going to be used for long time, disconnect the AC adaptor from the AC outlet.
• Be sure to use it near the wall outlet. If a malfunction occurs, disconnect the plug from the wall outlet at once.
• When the AC adaptor is plugged in, the apparatus is not completely disconnected from the main power source, even when the unit is turned off.
• AC adaptor is used as the disconnect device. It shall remain readily operable and should not be obstructed during intended use. To be completely disconnected the apparatus from supply mains, the AC adaptor of the apparatus shall be disconnected from the mains socket outlet completely.

GENERAL OPERATION

1. Press and hold button to turn on or turn off the unit.
2. Press the SOURCE button to select AUX or Bluetooth playback as desired.

The STANDBY indicator will turned the color as below:

3. Press the VOL+/- Buttons to adjust volume level.

Note: If no source is played, the unit will go to standby mode automatically after 2 hours.

LISTENING TO AUXILIARY SOURCE

1. Connect your auxiliary source (e.g. iPod / iPad / MP3 player) to the AUX jack (3.5mm ).
2. Press and hold the button to turn on the unit. Press the SOURCE button to select Auxiliary mode, purple light will be showed on indicator.
3. Start playback from your auxiliary source.
4. Adjust the volume to desired level.
5. To stop playback, disconnect your auxiliary source from the AUX jack.

BLUETOOTH PAIRING & LINKING OPERATION

The Bluetooth^® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by New One S.A.S is under license. Other trademarks and trade names are those of their respective owners.

Hereby, NEW ONE S.A.S, declares that this MUSE M-1050 BT is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The declaration of conformity may be consulted at http://www.muse-europe.com/conformity/M-1050BT.pdf

1. Turn off the Bluetooth functionality of other devices that were paired with your unit.
2. Press and hold button to turn on the unit.
3. Press SOURCE button to select Bluetooth mode, blue light will be showed on indicator. Your unit will be in pairing mode with a tone voice.
4. Turn on Bluetooth functionality on your Bluetooth device. Typically, Bluetooth controls are found on the device's tools or settings menu (see your user manual). Turn on Bluetooth connectivity and make your device "discoverable".
5. Clean out the paring list on your Bluetooth device.
6. Choose "add a new Bluetooth device" or "setup Bluetooth device" on your device. It will start to search. Once "M-1050 BT" shows on your device, select it. If your device prompts you for a pass code, please enter 0000. If the pairing attempt fails or times out, please start pairing procedure again (see steps 2-6).
7. After your device and the "M-1050 BT" have connected each other, a tone voice can be heard, and the indicator stay lit.
8. If the pairing fails, perform the following: Press the PAIR button until the Bluetooth indicator blinks quickly to enter the pairing mode. On the Bluetooth device, enable Bluetooth and select "M-1050 BT" from the device List (see step 6 above).

Play MUSIC from Bluetooth devices

Make sure the Bluetooth connection between the unit and the device is active.

TROUBLESHOOTING GUIDE

Symptom	Cause	Solution
No power	AC adaptor not plugged into wall outlet.	Plug it to the wall outlet properly.
	The unit is in Standby mode.	Press and hold button to turn on the unit.
No sound	Volume in minimum.	Adjust volume to a desired level.
	The connected device is not in playback mode.	Play the music in the
	Sound output of the connected device weak. (AUX IN & BLUETOOTH mode)	Adjust volume of connected device.
Sound distortion	Volume level too high	Reduce the volume level by press the VOL- button.
	Volume level of the connected device too high. (AUX IN & BLUETOOTH mode)	Reduce the volume level of the connected device.
Bluetooth reception failure	Not in the Bluetooth mode.	Try to do connection again.

• Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
• Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
• Only use attachments / accessories specified by the manufacturer.
• Unplug this apparatus during lightning storms or when unused for long periods of time.
• An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
• Do not overload wall outlets and extension cords as this can result in a risk or fire or electric shock.
• When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part. Unauthorized substitutions may resu in fire or electric shock or other hazards.

SPECIFICATIONS

Power source: AC 100-240V 50/60 Hz

Impedance of Speakers Loud speakers 8 Ohm x 2

Bluetooth working distance: Up to 10 meters measured in open space. (Wall and structures may affect range of device)