1. Manuals
  2. Brands
  3. Koyker Manuals
  4. Farm Equipment
  5. FLEXSTOR 1055
  6. Owner's manual

Koyker FLEXSTOR 1055 Owner's Manual

Grain bag unloader
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
MANUAL NO. 686410 RevA
12/23/2010
OWNERS MANUAL
Model 1055
Grain Bag
Unloader
BE SURE THIS MANUAL IS GIVEN TO THE
PURCHASER FOR FUTURE REFERENCE

Advertisement

Table of Contents
loading

Related Manuals for Koyker FLEXSTOR 1055

Summary of Contents for Koyker FLEXSTOR 1055

  • Page 1 MANUAL NO. 686410 RevA 12/23/2010 OWNERS MANUAL Model 1055 Grain Bag Unloader BE SURE THIS MANUAL IS GIVEN TO THE PURCHASER FOR FUTURE REFERENCE...

  • Page 2: Table Of Contents

    CONTENTS CONTENTS PAGE Introduction ........................0-3 SECTION 1 - SAFETY INFORMATION Safety Alert Symbols ....................1-1 Safety Information ....................... 1-2 Safety Decals ......................1-3, 1-4 Decals ..........................1-4 SECTION 2 - SPECIFICATIONS Specifications ........................ 2-1 SECTION 3 - FEATURES Features ........................3-1, 3-2 SECTION 4 - OPERATION Before Starting ......................
  • Page 3 CONTENTS CONTENTS PAGE SECTION 5 - PARTS DIAGRAM AND DESCRIPTION (Cont’d) Frame Assembly Parts List ................... 5-7 Front Frame Assembly Drawing ................... 5-8 Front Frame Assembly Parts List ................5-9, 5-10 Back Frame Assembly Drawing ................5-11, 5-12 Back Frame Assembly Parts List ................5-13, 5-14 Top Auger Assembly Drawing ..................

  • Page 4: Introduction

    INTRODUCTION The purpose of this manual is to explain the operation and maintenance of the Model 1055 Grain Bag Unloader. It also contains a parts list for reference, if replacement parts are needed. It is recommended that you read this manual in its entirety for the information available in order to provide the proper care and maintenance of the Model 1055 Grain Bag Unloader.

  • Page 5: Section 1 - Safety Information

    SECTION 1 - SAFETY INFORMATION SAFETY ALERT SYMBOLS The symbol shown below is used to call your attention to instructions concerning your personal safety. Watch for this symbol it points out important safety precautions. It means ATTENTION! Become Alert! Your Personal Safety Is Involved! Read the message that follows and be alert to the possibility of personal injury or death.

  • Page 6: Safety Information

    SECTION 1 - SAFETY INFORMATION SAFETY A careful operator is the best operator. Most accidents can be avoided by observing certain precautions. To help prevent accidents, read the following precautions before operating this equipment. Equipment should be operated only by those who are responsible and instructed to do so.

  • Page 7: Safety Decals

    SECTION 1 - SAFETY INFORMATION SAFETY DECALS P/N 666943 P/N 682785 P/N 687218 P/N 680292 P/N 686415...

  • Page 8: Decals

    SECTION 1 - SAFETY INFORMATION SAFETY DECALS P/N 686418 P/N 686419 P/N 687358 P/N 687344...

  • Page 9: Section 2 - Specifications

    SECTION 2 - SPECIFICATIONS FLEX-STOR GRAIN BAG UNLOADER 1055 Capacity* ....................8000 BU/HR Hitching ..................... Trailer or 3 pt Overall Transport Size Length ........................19’ 5” Width ........................8’ 6” Height ........................10’ 2” Tractor Requirements HP Minimum ......................90 HP PTO ....................

  • Page 10: Features

    SECTION 3 - FEATURES INITIAL SETUP: FUNCTION CONTROL VALVE The Flex-Stor Grain Bag Unloader MANIFOLD: 1055 requires no additional setup prior to operation. The Base Unit is shipped The function control valve manifold is from the factory completely assembled. were the operator controls the truck au- ger fold, truck auger swing, bag lift roll- TWO TYPES OF HITCHING: er, wheel direction, wheel speed, wind-...
  • Page 11 SECTION 3 - FEATURES DUAL BAG CUTTING KNIVES: The bag is cut on both the top and bot- tom by two straight edge sickle sec- tions. Replacement of the a dull blade is easy and inexpensive. BAG CUTTING LOCATION: The bag is cut 3 ft behind were the grain is being removed from the bag, which reduces the possibility of the bag ripping open down the length of the...

  • Page 12: Section 4 - Operation

    SECTION 4 - OPERATION BEFORE STARTING: NOTE: It will be easier to maneuver the GBU into position by using the  Make sure all operators have read the trailer hitch. manual and are aware of the operating procedures and hazards associated Leave roughly 10 ft between the with the Grain Bag Unloader 1055.
  • Page 13 SECTION 4 - OPERATION Hitch Top Tube Install Pin Remove Pins 3. Remove the two pins holding the hitch top tube in place. 6. Lift the hitch up to its operation position Securing Bracket and install the pin. Hitch Top Tube Install Pin 4.
  • Page 14 SECTION 4 - OPERATION Cat II Cat III Quick Attach Connect PTO to the GBU Cat II Quick Attach Remove the PTO Shaft from the transport storage brackets and connect it to the GBU. NOTE: There are three holes for the top link d Connect the other end of the PTO pin.

  • Page 15: 12. Unfold The Bag Lift Roller Wings

    SECTION 4 - OPERATION NOTE: Oil is only permitted to flow in one 13. Unfold the Gathering Auger Extensions. direction, so activate the circuit and check for hydraulic flow. Continuous flow needs to be Operation Position maintained for the GBU to operate. Select a hydraulic circuit that is capable of being locked for continuous flow.

  • Page 16: 15. Adjust The Conveyor Position Pin

    SECTION 4 - OPERATION Operators Station Lock Engagement Pin NOTE: The following functions will all be c) Lock the auger cage in place, make sure that the lock is controlled by the operators station. engaged. 15. Adjust the Conveyor Position pin 1”...
  • Page 17 SECTION 4 - OPERATION d Install the pin clips onto both ends of the pin. Rest Conveyor on position pin Rear Roller Valve Remove Pins NOTE: Use the “Rear Roller” valve on the operators station. Lower the Bag Lift Roller until the conveyor rests on the pin.

  • Page 18: Preparing The Bag

    SECTION 4 - OPERATION DANGER: Make sure there are no overhead objects that the main auger will hit will extending and swinging it into position. NOTE: The conveyor position pin needs to be in its operation position (See page 4-5 for instructions). Make sure the conveyor is resting on the position pin before swinging the auger.

  • Page 19: Maneuvering The Gbu Into The Bag

    SECTION 4 - OPERATION Cut the top half way up the slope Lift the Conveyor so the Auger Cages don’t grab the plastic when backing up to the grain Using the Bag Lift Roller, lift the  conveyor to ensure the auger cages will not grab the bag when backing up.

  • Page 20: Using The Tractor

    SECTION 4 - OPERATION Using the Tractor: Drive Wheel Valve Lock Out Hubs b) Move the “Drive Wheel” valve in either direction to lock the hubs a) Make sure the wheel lock out c) Put the tractor in neutral and hubs are in the free position and release parking brake.

  • Page 21: Connecting The Bag To The Spools

    SECTION 4 - OPERATION  The door is closed. Lower the Bag Lift Roller  The bushing is inserted correctly.  The bolt is properly tightened. 2. Route the Bag  Route the bag to the spools as follows. Over Bag Lift Roller 2.
  • Page 22 SECTION 4 - OPERATION Above the Gathering Augers Joins the bottom part at the Vertical Frame Guide Roller b) The top plastic goes above the Gathering Augers and meets up with the bottom part at the Frame Guide Roller. 3. Connect the plastic to the spools by inserting a small piece through the front side of the “wedge”.
  • Page 23 SECTION 4 - OPERATION Determine if the wheel drive will be  needed to assist the spools in moving the GBU back into the bag. Ensure the wheel lock out hubs are in the appropriate position before moving the machine (see page 4-8 &...
  • Page 24 SECTION 4 - OPERATION Engage the “Winders” and “Drive Adjust the height of the Bag Lift Roller.   Wheel” (if needed) valves. Adjust there NOTE: Although the height is not that speed accordingly to acquire the correct critical, there is a spot that seems to conveyor operating pressure.

  • Page 25: Switching Trucks

    SECTION 4 - OPERATION SWITCHING TRUCKS: END OF THE BAG: When the transport container is full, When using the Drive Wheels, run them   disengage the “Drive Wheel” and until the GBU gathering augers get to the “Winder” valve. “Bull nose”.

  • Page 26: Removing The Plastic From The Spools

    SECTION 4 - OPERATION REMOVING THE PLASTIC FROM THE SPOOLS: Before removing the plastic from the spools, the plastic needs to be cut from the remaining portion of the bag. NOTE: The plastic can be removed whenever the operator prefers. This is helpful to make smaller, more manageable bales.
  • Page 27 SECTION 4 - OPERATION WARNING: Make sure the area is clear of personnel and objects before removing the plastic. 8. Install the inner spool plate back onto the spools and insert the two pin clips. Bag Removal Valve 9. Install the outer spool plate and close the 6.
  • Page 28 SECTION 4 - OPERATION SWITCHING FROM OPERATION 11. Remove the top tube from its operation location. TO TRANSPORT POSITION: 12. Install the two pins to secure the top tube DANGER Make sure to block the tires to in transport position. ensure the Grain Bag Unloader will 13.

  • Page 29: Section 5 - Parts Diagram And Description

    SECTION 5 - PARTS DIAGRAM AND DESCRIPTION MAIN ASSEMBLY DRAWING...

  • Page 30: Main Assembly Drawing-Decals

    SECTION 5 - PARTS DIAGRAM AND DESCRIPTION MAIN ASSEMBLY DRAWING –DECALS...

  • Page 31: Main Assembly Drawing-Spools

    SECTION 5 - PARTS DIAGRAM AND DESCRIPTION MAIN ASSEMBLY DRAWING –SPOOLS...

  • Page 32: Main Assembly Parts List

    SECTION 5 - PARTS DIAGRAM AND DESCRIPTION MAIN ASSEMBLY PARTS LIST ITEM NO. PART NUMBER DESCRIPTION 684864 1.5" - 4 BOLT FLANGE BEARING 684873 LIFT CYLINDER 686411 FRAME ASSY 686431 SPOOL LOCK INSERT ZINC PLATED 686466 IN-LINE CHECK VAVLE 686624 PILOT CHECK VAVLE 686628 CAT II LOWER LINK ARM PIN ZINC...
  • Page 33 SECTION 5 - PARTS DIAGRAM & LIST MAIN ASSEMBLY PARTS LIST (Cont’d) 640128 NUT - .313-18 GR 2 CENTER LOCK 640151 WASHER - 5/16" SPRING LOCK 640154 WASHER - 3/8" FLAT 640162 WASHER - 3/4" SPRING LOCK 651880 SCREW-.3125-18 X 1.25 GR 5 HHC 653224 SCREW - .75-10 X 2.75 GR 8 HHC 654453...

  • Page 34: Frame Assembly Drawing

    SECTION 5 - PARTS DIAGRAM AND DESCRIPTION FRAME ASSEMBLY DRAWING...

  • Page 35: Frame Assembly Parts List

    SECTION 5 - PARTS DIAGRAM AND DESCRIPTION FRAME ASSEMBLY PARTS LIST ITEM NO. PART NUMBER DESCRIPTION 682220 EXT LONG SIDE WIND JACK 686482 PIN-.75" X 4.00" 686617 BALL VALVE BRACKET 686845 HITCH TOP TUBE STORAGE HOLE PLATE 686848 FRAME ASSY - BACK HALF 686858 FRAME ASSY - FRONT HALF 686941...

  • Page 36: Front Frame Assembly Drawing

    SECTION 5 - PARTS DIAGRAM AND DESCRIPTION FRONT FRAME ASSEMBLY DRAWING...

  • Page 37: Front Frame Assembly Parts List

    SECTION 5 - PARTS DIAGRAM AND DESCRIPTION FRONT FRAME ASSEMBLY PARTS LIST ITEM NO. PART NUMBER DESCRIPTION 682214 1" PILLOW BLOCK BEARING 686416 GEAR BOX VENT BUSHING 686417 GEAR BOX PRESSURE RELIEF VENT 686427 PTO SPLINED SHAFT WLDT 686554 PTO SECURING STORAGE PLATE 686605 HOPPER CAGE FASTENER PLATE 686639...
  • Page 38 SECTION 5 - PARTS DIAGRAM AND DESCRIPTION FRONT FRAME ASSEMBLY PARTS LIST (Cont’d) ITEM NO. PART NUMBER DESCRIPTION 640145 NUT - .750 - 10 GR 2 LOCK NYLON INSERT 640150 WASHER - 1/4" FLAT 640153 WASHER - 3/8" SPRING LOCK 640154 WASHER - 3/8"...

  • Page 39: Back Frame Assembly Drawing

    SECTION 5 - PARTS DIAGRAM AND DESCRIPTION BACK FRAME ASSEMBLY DRAWING 5-11...
  • Page 40 SECTION 5 - PARTS DIAGRAM AND DESCRIPTION BACK FRAME ASSEMBLY DRAWING 5-12...

  • Page 41: Back Frame Assembly Parts List

    SECTION 5 - PARTS DIAGRAM AND DESCRIPTION BACK FRAME ASSEMBLY PARTS LIST ITEM NO. PART NUMBER DESCRIPTION 686310 SPACER TUBE 686406 AXLE LARGE PLASTIC WASHER 686407 AXLE SNAP RING 686408 AXLE SMALL WASHER KIT 686413 LOCK OUT HUB SNAP RING 686429 OIL TANK SIDE SPACERS 686430...
  • Page 42 SECTION 5 - PARTS DIAGRAM AND DESCRIPTION BACK FRAME ASSEMBLY PARTS LIST (Cont’d) ITEM NO. PART NUMBER DESCRIPTION 651880 SCREW-.3125-18 X 1.25 GR 5 HHC 640898 SCREW - 14MM - 1.5 X 40 GR 8.8 HHC 680140 SCREW - .375 - 16 X 1.25 CARRIAGE 682413 NUT - .375 X 16 FLANGE 682441...

  • Page 43: Top Auger Assembly Drawing

    SECTION 5 - PARTS DIAGRAM AND DESCRIPTION TOP AUGER ASSEMBLY DRAWING 5-15...

  • Page 44: Top Auger Assembly Parts List

    SECTION 5 - PARTS DIAGRAM AND DESCRIPTION TOP AUGER ASSEMBLY PARTS LIST ITEM NO. PART NUMBER DESCRIPTION 686613 SNOUT CENTERING BOLT RING PLATE 686619 SQUARE AUGER STOP WLDT 686876 SNOUT RUBBER SUPPORT SIDE STRIP 686877 SNOUT RUBBER SUPPORT FRONT PLATE 686878 SNOUT RUBBER SUPPORT SEAM STRIP 686949...

  • Page 45: Bag Lift Roller Assembly Drawing

    SECTION 5 - PARTS DIAGRAM AND DESCRIPTION BAG LIFT ROLLER ASSEMBLY DRAWING 5-17...

  • Page 46: Bag Lift Roller Assembly Parts List

    SECTION 5 - PARTS DIAGRAM AND DESCRIPTION BAG LIFT ROLLER ASSEMBLY PARTS LIST ITEM NO. PART NUMBER DESCRIPTION 686571 PICKUP WING ROLLER WLDT 686575 PICKUP WING EXT WLDT 686579 PICKUP LH WING WLDT 686587 PICKUP RH WING WLDT 686593 PICKUP WING LH PIVOT MOUNT WLDT 686597 PICKUP WING RH PIVOT MOUNT WLDT 686604...

  • Page 47: Conveyor Assembly Drawing

    SECTION 5 - PARTS DIAGRAM AND DESCRIPTION CONVEYOR ASSEMBLY DRAWING 5-19...
  • Page 48 SECTION 5 - PARTS DIAGRAM AND DESCRIPTION CONVEYOR ASSEMBLY DRAWING (Cont’d) 5-20...

  • Page 49: Conveyor Assembly Parts List

    SECTION 5 - PARTS DIAGRAM AND DESCRIPTION CONVEYOR ASSEMBLY PARTS LIST ITEM NO. PART NUMBER DESCRIPTION 684864 1.5" - 4 BOLT FLANGE BEARING 686103 CHAIN TIGHTNER BOLT 686493 CROSS AUGER CAGE BACK LOCK PLATE 686496 CAGE LOCK PLATE PIN 686603 SQUARE FLANGE BEARING 686640 CLEAN OUT AUGER ASSY...
  • Page 50 SECTION 5 - PARTS DIAGRAM AND DESCRIPTION CONVEYOR ASSEMBLY PARTS LIST (Cont’d) ITEM NO. PART NUMBER DESCRIPTION 640139 NUT - .500-13 GR 2 HEX 640018 SCREW - .3125 X 1.00 GR 5 CAR 682524 NUT - .3125 X 18 FLANGE 686183 SCREW - .3125 X 1.25 GR 5 CAR 700638...

  • Page 51: Clean Out Auger Assembly Drawing

    SECTION 5 - PARTS DIAGRAM AND DESCRIPTION CLEAN OUT AUGER ASSEMBLY DRAWING 5-23...

  • Page 52: Clean Out Auger Assembly Parts List

    SECTION 5 - PARTS DIAGRAM AND DESCRIPTION CLEAN OUT AUGER ASSEMBLY PARTS LIST ITEM NO. PART NUMBER DESCRIPTION 686038 1" SQUARE FLANGE BEARING 686641 CLEAN OUT AUGER CAGE WLDT 686650 CLEAN OUT AUGER MOTOR PLATE 686651 CLEAN OUT AUGER END PLATE 686652 CROSS AUGER BEARING PLATE 686653...

  • Page 53: Pto Pump Hydraulics Drawing

    SECTION 5 - PARTS DIAGRAM AND DESCRIPTION PTO PUMP HYDRAULIC DRAWING 5-25...
  • Page 54 SECTION 5 - PARTS DIAGRAM AND DESCRIPTION PTO PUMP HYDRAULIC PARTS LIST *REFERENCE PARTS* ITEM NO. PART NO. DESCRIPTION QTY. 686754 OIL TANK 686969 PRIORITY VALVE 659840 FITTING - HYD ADA 12MJX-12ORM (LABEL "P") 686479 FITTING - HYD ADA 16MJX-16ORM (LABEL "T") 687209 PTO PUMP 687603...

  • Page 55: Hydraulic Drawing

    SECTION 5 - PARTS DIAGRAM AND DESCRIPTION HYDRAULIC DRAWING 5-27...
  • Page 56 SECTION 5 - PARTS DIAGRAM AND DESCRIPTION HYDRAULIC DRAWING 5-28...

  • Page 57: Hydraulic Parts List

    SECTION 5 - PARTS DIAGRAM AND DESCRIPTION HYDRAULIC PARTS LIST ITEM NO. PART NO. DESCRIPTION QTY. 684873 ROLLER LIFT CYLINDER 686466 IN LINE CHECK VALVE 686478 BALL VALVE 686624 PILOT CHECK VALVE - TOP 686624 PILOT CHECK VALVE - BOTTOM 686910 SPOOL PUSH CYLINDER - TOP 686910...
  • Page 58 SECTION 5 - PARTS DIAGRAM AND DESCRIPTION HYDRAULIC PARTS LIST ITEM NO. PART NO. DESCRIPTION QTY. 12-X 750172 HYD - ORIFICE 1/16" 12-Y 659968 FITTING - HYD ADA 6MJX-8ORM 12-Z 659968 FITTING - HYD ADA 6MJX-8ORM 12-Z 656254 FITTING - HYD ADA 8ORM-8ORF 12-Z 750172 HYD - ORIFICE 1/16"...
  • Page 59 SECTION 5 - PARTS DIAGRAM AND DESCRIPTION HYDRAULIC PARTS LIST ITEM NO. PART NO. DESCRIPTION QTY. 686459 HYD HOSE .375-77 6FJX-6FJX90S 686460 HYD HOSE .375-103 6FJX-6FJX90S 686461 HYD HOSE .375-103 8FJX-8FJX 686462 HYD HOSE .375-98 6FJX-6FJX90S 686463 HYD HOSE .375-140 8FJX-8FJX 686464 HYD HOSE .375-158 8FJX-8FJX 686465...

  • Page 60: Electrical Drawing

    SECTION 5 - PARTS DIAGRAM AND DESCRIPTION ELECTRICAL DRAWING 5-30...
  • Page 61 SECTION 5 - PARTS DIAGRAM AND DESCRIPTION ELECTRICAL ITEM NO. PART NO. DESCRIPTION QTY. 687603 OIL COOLER 687613 TRACTOR ELECTRICAL CONECTOR HYDRAULIC GOVERNOR ASSY ITEM NO. PART NO. DESCRIPTION QTY. 687641 HYD GOVERNOR ASSY 687649 GOVERNOR WIRING HARNESS 687650 SENSOR SWITCH 687651 12V DIN COIL 687652...

  • Page 62: Section 6 - Service

    SECTION 6 - SERVICE GENERAL INFORMATION  Adjusting, lubricating or service should be preformed on a flat level surface only.  Set the parking brake of tractor, shut off tractor engine, and relieve the pressure in the hydraulic system before adjusting, lubricating, or servicing the Grain Bag Unloader. ...

  • Page 63: Hourly Service Schedule

    SECTION 6 - SERVICE HOURLY SERVICE SCHEDULE Periodic Service Daily Check/tighten hardware Check Hydraulic lines and fittings Check pins, bushings, and zerks Grease zerks Clean out debris from equipment Check/Tighten Conveyor Chain Check/Tighten Tires KEY: “S” = REQUIRED SERVICE HOURLY INTERVAL (Continue repeating service intervals) “I”...

  • Page 64: Torque Specifications

    SECTION 6 - SERVICE TORQUE SPECIFICATIONS 1. Tightening Bolts & Nuts Check all GBU bolts and nuts for tightness every 50 working hours. The movement of the over rough terrain may cause bolts to come under pressure and over a long period of time some slight stretching of the bolt may occur.
  • Page 65 SECTION 6 - SERVICE GRAIN BAGGER GREASE ZERK LOCATIONS  There are 60 grease zerks located on the Grain Bag Unloader. Four on the Truck Auger Swing Pivot Two on the PTO Grease Zerk Grease Zerk Grease Zerk Grease Zerk There is two grease zerk per bushing, two bushings There is one grease zerk per yokes, two yokes per per pivot and one Truck Auger Swing Pivot per...
  • Page 66 SECTION 6 - SERVICE GRAIN BAGGER GREASE ZERK LOCATIONS (Cont’d) Two on the Bag Lift Roller Pivot Four on the Bag Lift Roller Wing Pivot Grease Zerk Grease Zerk Grease Zerk There is one grease zerk per bushing, one bushing There is one grease zerk per bushing, two bushings per pivot and two Bag Lift Roller Pivots per GBU per pivot and two Bag Lift Roller Wing Pivots per...
  • Page 67 SECTION 6 - SERVICE GRAIN BAGGER GREASE ZERK LOCATIONS (Cont’d) One - Bottom Truck Auger One - Top Truck Auger Grease Zerk Grease Zerk There is one grease zerk per bearing, one bearing There is one grease zerk per bearing, one bearing per auger and one Bottom Truck Auger per GBU.
  • Page 68 SECTION 6 - SERVICE GRAIN BAGGER GREASE ZERK LOCATIONS (Cont’d) Two - Upper Conveyor Shaft Four - Gathering Augers Grease Zerk Grease Zerk Grease Zerk Grease Zerk There is one grease zerk per bearing, two bearings There is one grease zerk per bearing, two bearings per shaft and one Upper Conveyor Shaft per GBU.
  • Page 69 SECTION 6 - SERVICE GRAIN BAGGER GREASE ZERK LOCATIONS (Cont’d) Two - Clean Out Auger One - Charge Auger Grease Zerk Grease Zerk Grease Zerk There is one grease zerk per bearing, two bearings There is one grease zerk per bearing, one bearing per auger and Clean Out Auger per GBU.
  • Page 70 SECTION 6 - SERVICE GRAIN BAGGER GREASE ZERK LOCATIONS (Cont’d) Four - Vertical Outer Bag Guide Roller Four - Horizontal Bag Guide Roller Grease Zerk Grease Zerk Grease Zerk Grease Zerk There is one grease zerk per bearing, two bearings There is one grease zerk per bearing, two bearings per guide roller and two Vertical Outer Bag Guide per guide roller and two Horizontal Bag Guide...

  • Page 71: Section 7 - Troubleshooting

    SECTION 7 - TROUBLESHOOTING TRACTOR HYDRAULIC SYSTEM Problem Possible Cause Solution None of the functions will No Hydraulic Flow Make sure the Tractor Hydraulic lever is locked in work position for continuous flow. Use a different tractor port. Tractor hoses are backwards Reverse the hoses on the tractor.

  • Page 72: Trouble Shooting

    SECTION 7 - TROUBLESHOOTING GBU HYDRAULIC SYSTEM Problem Possible Cause Solution The Conveyor motor will not The PTO is not on The PTO needs to be on for the pump to work. turn engage the tractor PTO. Cold Start The system oil is cold and needs to be warmed up first.

  • Page 73: Section 8 - Optional Kits

    SECTION 8 - OPTIONAL KITS EXTENSION KIT DRAWING...
  • Page 74 SECTION 8 - OPTIONAL KITS EXTENSION KIT PARTS LIST ITEM NO. PART NUMBER DESCRIPTION 686575 PICKUP WING EXT WLDT 686666 OUTSIDE CROSS AUGER CAGE WLDT 686675 RH OUTER CROSS AUGER WLDT 686678 LH OUTER CROSS AUGER WLDT 686747 PICKUP WING EXT ROLLER WLDT 680140 SCREW - .375 - 16 X 1.25 CARRIAGE 682413...

  • Page 75: Limited Warranty

    SECTION 9 - LIMITED WARRANTY LIMITED WARRANTY Thank you for purchasing a quality product. Your satisfaction with this product is very important to us. This manual will help you understand the function, service intervals and warranty of your new product. It is the retail customer’s responsibility to inspect the product or part before using. Before operating or allowing anyone to operate a this product, please take time to read the manual thoroughly.

  • Page 76: Warranty Limitations And Exclusions

    WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A 2 PARTICULAR PURPOSE. NOT WITHSTANDING ANY OTHER OR PRIOR STATEMENT, WRITTEN OR ORAL, KOYKER MAKES NO OTHER WARRANTIES REGARDING THE QUALITY OF THE PRODUCTS OR THE MATERIALS CONTEMPLATED HEREUNDER. No warranty is given by the manufacturer for parts, components, or trade accessories furnished by the manufacturer but not manufactured by it.
  • Page 77 SECTION 9 - LIMITED WARRANTY Among other conditions, the manufacturer’s warranty WILL NOT apply: 1. Products or parts that are subject to misuse, abuse, and/or negligence. 2. For surface wear, scheduled maintenance parts, and other items that the manufacturer deems expendable.

Table of Contents