Operating Instruction and Parts Manual
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or
property damage! Retain instructions for future reference.
Description
The submersible pump is designed for
indoor home sump applications. The
unit is equipped with a 3-prong
grounding type power cord. Motor is
oil filled and sealed for cooler running
and designed to operate under water.
This pump is not suitable for aquatic
life.
This sump pump is provided with
Switch Genius™ Technology to control
the water level. When water is
detected, the pump will start
automatically.
U n p a c k i n g
Inspect this unit before it is used.
Occasionally, products are damaged
during shipment. If the pump or
components are damaged, return the
unit to the place of purchase for
replacement. Failure to do so could
result in serious injury or death.
I m p o rtant Safety
I n s t ru c t i o n s
READ AND FOLLOW ALL
I N S T R U C T I O N S .
Safety Guidelines
This manual contains information that is
very important to know and understand.
This information is provided for SAFETY
and to PREVENT EQUIPMENT PROBLEMS.
To help recognize this information,
observe the following symbols:
Danger indicates
an imminently
hazardous situation which, if not
avoided, will result in death or serious
injury.
Warning indicates
a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping.
© 2008 Wayne Water Systems
S u b m e r s i b l e
Sump Pump
Caution indicates
a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
Notice indicates
important
information, that if not followed, may
cause damage to equipment.
General Safety
I n f o rm a t i o n
CALIFORNIA PROPOSITION 65
This product or its
power cord may
contain chemicals, including lead,
known to the State of California to
cause cancer and birth defects or other
reproductive harm. Wash hands after
handling.
S p e c i f i c a t i o n s
Power supply requirements
M o t o r
Horsepower/Amp Ratings
Liquid temperature range
Circuit requirements
D i m e n s i o n s
Cut-in level (factory set)
Cut-out level (factory set)
C o n s t ru c t i o n
Motor housing
V o l u t e
I m p e l l e r
S h a f t
S e a l s
D i s c h a r g e
Motor Cover
For parts, product & service information
visit www.waynepumps.com
11 inch
Diameter
Minimum
Incoming
Water
Inlet Pipe
13 inch min.
Check
Valve
Figure 1 - Typical Installation
120V, 60 hz
Single phase, oil filled
1 /3 HP/9.5 A ( C D U C A P 7 2 5 )
1 /2 HP/10 A ( C D U C A P 8 5 0 )
3/4 HP/10 A ( C D U C A P 9 9 5 )
1 HP/10 A ( C D U C A P 1 0 0 0 )
40°F to 120°F
15 amps (min)
11-1/2 inch high x 9-3/4 inch base
8 inch
Approx. 3inch
Cold rolled steel, Stainless steel (CDUCAP995)
Cast iron
Glass reinforced thermoplastic
Low carbon steel
Buna N
1-1/2 inch NPT
Glass reinforced thermoplastic
CDUCAP Series
Discharge
Pipe
GFCI
Protected
Outlet
On @ 8
inches
Switch
Off @
approx.
3 inches
352401-001 12/08