Operating Instructions And Parts Manual
Instructions d'Utilisation et Manuel de Pièces
Manual de Instrucciones de Operación y Piezas
Notes / Notas
CDUCAP Series
2 0- S p
Operating Instruction and Parts Manual
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or
property damage! Retain instructions for future reference.
S u b m e r s i b l e
Sump Pump
Description
The submersible pump is designed for
hazardous situation which, if not
indoor home sump applications. The
avoided, may result in minor or
unit is equipped with a 3-prong
moderate injury.
grounding type power cord. Motor is
oil filled and sealed for cooler running
and designed to operate under water.
information, that if not followed, may
cause damage to equipment.
This pump is not suitable for aquatic
life.
General Safety
This sump pump is provided with
I n f o rm a t i o n
Switch Genius™ Technology to control
the water level. When water is
detected, the pump will start
CALIFORNIA PROPOSITION 65
automatically.
U n p a c k i n g
contain chemicals, including lead,
Inspect this unit before it is used.
known to the State of California to
Occasionally, products are damaged
cause cancer and birth defects or other
during shipment. If the pump or
reproductive harm. Wash hands after
components are damaged, return the
handling.
unit to the place of purchase for
S p e c i f i c a t i o n s
replacement. Failure to do so could
result in serious injury or death.
Power supply requirements
M o t o r
Horsepower/Amp Ratings
I m p o rt ant Safety
I n s t ru c t i o n s
READ AND FOLLOW ALL
I N S T R U C T I O N S .
Liquid temperature range
Circuit requirements
Safety Guidelines
D i m e n s i o n s
This manual contains information that is
Cut-in level (factory set)
very important to know and understand.
Cut-out level (factory set)
This information is provided for SAFETY
and to PREVENT EQUIPMENT PROBLEMS.
To help recognize this information,
C o n s t ru c t i o n
observe the following symbols:
Motor housing
Danger indicates
V o l u t e
an imminently
I m p e l l e r
hazardous situation which, if not
avoided, will result in death or serious
S h a f t
injury.
S e a l s
Warning indicates
D i s c h a r g e
a potentially
Motor Cover
hazardous situation which, if not
avoided, could result in death or
serious injury.
REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping.
© 2008 Wayne Water Systems
For parts, product & service information
visit www.waynepumps.com
CDUCAP Series
Caution indicates
Discharge
a potentially
Pipe
GFCI
11 inch
Protected
Diameter
Outlet
Minimum
Notice indicates
important
Incoming
Water
Inlet Pipe
13 inch min.
This product or its
power cord may
Check
Valve
Figure 1 - Typical Installation
120V, 60 hz
Single phase, oil filled
1 /3 HP/9.5 A ( C D U C A P 7 2 5 )
1 /2 HP/10 A ( C D U C A P 8 5 0 )
3/4 HP/10 A ( C D U C A P 9 9 5 )
1 HP/10 A ( C D U C A P 1 0 0 0 )
40°F to 120°F
15 amps (min)
11-1/2 inch high x 9-3/4 inch base
8 inch
Approx. 3inch
Cold rolled steel, Stainless steel (CDUCAP995)
Cast iron
Glass reinforced thermoplastic
Low carbon steel
Buna N
1-1/2 inch NPT
Glass reinforced thermoplastic
352401-001 12/08
On @ 8
inches
Switch
Off @
approx.
3 inches