Advertisement
Quick Links
Operating Instructions and Parts Manual
SPECIFICATIONS
POWER SUPPLY REQUIREMENTS
MOTOR
HORSEPOWER
CIRCUIT REQUIREMENTS
DIMENSIONS
ON LEVEL (FACTORY SET)
OFF LEVEL (FACTORY SET)
CONSTRUCTION
Stainless Steel, (CDU1000, CDU980E,
MOTOR HOUSING
CDU800SS, CDU790SS) Coated Steel
(CDU800, CDU790, SPF33, SPF50, CDT50)
Reinforced Thermoplastic (WST33)
VOLUTE
CDU1000, CDU980E,
CDU800, CDU800SS
CDU790, CDU790SS,
CDT50
Cast Iron
IMPELLER
Glass Reinforced Thermoplastic
SHAFT
Steel
PERFORMANCE GAL/HR
Model
HP
0 ft
CDU1000
1
6100
CDU980E
3/4
5490
CDU800SS
1/2
5100
CDU800, CDT50
CDU790SS,
1/3
4600
CDU790
SPF50
1/2
4300
SPF33
1/3
3750
WST33
1/3
3000
*Images are for illustration purposes only.
Not all models are shown.
© 2020, WAYNE/Scott Fetzer Company
120 V, 60 Hz
Single Phase, Dielectric Oil Filled
1 HP .................... (CDU1000)
3/4 HP ................ (CDU980E)
1/2 HP ............ (CDU800SS, CDU800,
............................. SPF50, CDT50)
1/3 HP ........... (CDU790SS, CDU790,
................................SPF33, WST33)
15 A (minimum)
11-1/2 in. high x 9-3/4 in. base
Vertical: Approximately 9 in.
Tether: Approximately 13 in.
Vertical: Approximately 4 in.
Tether: Approximately 7 in.
SPF33, SPF50, WST33
Glass Reinforced Thermoplastic
Discharge Head (Lift Distance)
5 ft
10 ft
15 ft
20 ft
5460
5100
4560
3840
5076
4600
4100
3500
4500
3840
3060
2040
3810
3060
2220
1200
3900
3360
2700
1260
3300
2718
1920
-
2610
2130
1404
400
Please read and save these instructions. Read carefully before attempting to assemble, install,
operate or maintain the product described. Protect yourself and others by observing all safety
information. Failure to comply with instructions could result in personal injury and/or property
damage! Retain instructions for future reference.
Intended for Indoor Use Only
www.waynepumps.com
Submersible Sump Pump
Vertical Float Switch
Tether Float Switch
600002W-001 F 08/20
Sumps
Advertisement
Related Manuals for Wayne CDU800SS
Summary of Contents for Wayne CDU800SS
- Page 1 120 V, 60 Hz MOTOR Single Phase, Dielectric Oil Filled HORSEPOWER 1 HP ....(CDU1000) 3/4 HP ....(CDU980E) Vertical Float Switch 1/2 HP .... (CDU800SS, CDU800, ......SPF50, CDT50) 1/3 HP ... (CDU790SS, CDU790, ........SPF33, WST33) CIRCUIT REQUIREMENTS 15 A (minimum) DIMENSIONS 11-1/2 in.
-
Page 2: Safety Signal Words
INSTALLATION MANUAL SUMP PUMP DESCRIPTION Sump pumps are automatic pumps used to remove ground water from sump pits. The most common application is for This pump is not designed to handle salt water, brine, laundry basement drainage to prevent flooding in residential buildings. discharge, water softener, sewage, grey water, or any other These sumps are designed to pump clear water only. - Page 3 INSTALLATION MANUAL NEVER HANDLE A PUMP or motor with wet hands or when standing on a wet or damp floor while the pump is plugged into the power supply. NE JAMAIS MANIPULER UNE POMPE ou un moteur de pompe avec CAUTION INDICATES A POTENTIALLY HAZARDOUS SITUATION les mains mouillées ou debout dans l’eau ou sur une surface WHICH, IF NOT AVOIDED, MAY RESULT IN MINOR OR...
- Page 4 INSTALLATION MANUAL TYPICAL SUMP INSTALLATION DIAGRAMS DO NOT USE THIS PUMP IN MUD, SAND, CEMENT, OIL CHEMICALS, GREY WATER, OR ANY OTHER WATER THAT IS NOT CLEAR GROUND WATER. Tether Submersible Sump NE PAS UTILISER CETTE POMPE DANS LA BOUE, LE SABLE, LE CIMENT, LES PRODUITS CHIMIQUES À...
- Page 5 Rigid PVC pipe is required. Do not use flex hosing in a permanent application. 7. Install a check valve (required) to prevent back-flow. The Wayne check valve (62061-WYN1) may be positioned just above the basin to allow easy removal of the pump for cleaning and service.
-
Page 6: Troubleshooting Warnings
INSTALLATION MANUAL TROUBLESHOOTING WARNINGS 1. Submersible pump models have permanently lubricated bearings and require no additional lubrication. 2. Submersible pumps contain dielectric oil for cooling. ALWAYS DISCONNECT THE PUMP FROM POWER SUPPLY before Dielectric oil can be harmful to the environment. Follow installing, servicing or making any adjustments. - Page 7 INSTALLATION MANUAL TROUBLESHOOTING CHART (CONTINUED) Symptoms Possible Cause(s) Suggested Remedies Pump trips GFCI 1. Bad GFCI 1. Contact an electrician to replace GFCI 2. Bad pump 2. Replace pump Pump operates 1. Worn bearings 1. Replace pump noisily or vibrates 2.
- Page 8 INSTALLATION MANUAL AND REPLACEMENT PARTS REPAIR KITS REF. NO. DESCRIPTION PART NUMBER FLOAT KIT 60038-WYN1 TETHER SWITCH 56835-WYN1...
- Page 9 For one year for SPF33 and SPF50 models, two years for CDT50, WST33, three years for CDU790 and CDU800 models, and five years for CDU790SS, CDU800SS, CDU980E, and CDU1000 from the date of purchase, from an authorized dealer, Wayne Water Systems will repair or replace, at its option for the original purchaser, any part or parts of its Sump Pumps or Water Pumps (“Product”) found upon examination by...