Coding A Transmitter; Storing The Transmitter Code; Remotely Coding Transmitters - B&D PanelMax SDO-8V3 Installation Instructions Manual

PanelMax installation instructions

15. Coding a Transmitter

15.1 Storing the Transmitter Code

3 . 0 C O D I N G A R E M O T E C O N T R O L
The opener can only be operated from remote
tip
controllers that have been programmed into its
memory. Up to 64 remotes can be programmed.
S T E P O N E
Switch power on and
remove controls cover
S T E P T H R E E
3 . 0 C O D I N G A R E M O T E C O N T R O L
The opener can only be operated from remote
tip
controllers that have been programmed into its
memory. Up to 64 remotes can be programmed.
HOLD for 3 sec
HOLD
RELEASE
S T E P O N E
HOLD for 3 sec
Opener
ashes & Release both
buttons
beeps
Switch power on and
remove controls cover
R E M O T E L Y C O D I N G A R E M O T E C O N T R O L
S T E P T H R E E
Remotely coding works when you have a
tip
pre-coded remote control and are in range of the
opener.
S T E P O N E
HOLD for 3 sec
HOLD
RELEASE
HOLD for 3 sec
Opener
Release both
ashes &
Take a pre-coded
beeps buttons
remote and press the
button to duplicate

15.2 Remotely Coding Transmitters

R E M O T E L Y C O D I N G A R E M O T E C O N T R O L
S T E P T H R E E
Remotely coding works when you have a
Opener ashes & beeps
tip
pre-coded remote control and are in range of the
opener.
HOLD for 3 sec
S T E P O N E
RELEASE
HOLD for 3 sec
Take new
RELEASE
remote
Take a pre-coded
4 . 0 C H A N G I N G A B A T T E R Y
remote and press the
button to duplicate
tip Battery Type: 1 x CR2032.
S T E P T H R E E
S T E P O N E
Opener ashes & beeps
Check Light
HOLD for 3 sec
Status Table
RELEASE
HOLD for 3 sec
HOLD
Take new
RELEASE
remote
S T E P T W O
4 . 0 C H A N G I N G A B A T T E R Y
Use screwdriver
to remove scew
tip
Battery Type: 1 x CR2032.
and open
S T E P O N E
S T E P T W O
Press till remote
repeatedly LED lit
S T E P F O U R
Then re t controls cover
S T E P T W O
S T E P F I V E
Press to test
Press till remote
repeatedly LED lit
S T E P F O U R
S T E P T W O
Then re t controls cover
Use a pen,
S T E P F I V E
HOLD for 2 sec
the middle button
Press to test
through the
coding hole
S T E P F I V E
Opener stops ashing &
beeping
S T E P T W O
Press to test
Use a pen,
HOLD for 2 sec
the middle button
through the
coding hole
S T E P F I V E
Light Status Battery
Opener stops ashing &
beeping
Solid OK
Flashing Replace
Press to test
No light Replace
S T E P T H R E E
Use non-metallic
object to push
out.
Light Status Battery
NOTE: To code other transmitter functions, at STEP THREE
refer to below table of buttons to press.
TRANSMITTER
FUNCTION
Open / Stop / Close
PET (Pedestrian) Mode
Open
Light
Vacation Mode
Aux Output
* The button coded for open only function can close the door
if you hold the button for 4 seconds, when the door is fully open..
NOTE: The opener will flash and beep during coding,
refer to below table for status indication..
MAIN LIGHT & BEEPER
ON + 2 x
OFF + 2 x
x 2, then OFF + 2 x
x 4, then OFF + 4 x
Remote code set is disabled when:
tip
• powered by battery backup
• the service indicator is active
• when the door is indicating that it was
prevented from closing by a P .E beam
being blocked
16
BUTTON
HOLD
HOLD
HOLD
HOLD HOLD
HOLD HOLD
HOLD HOLD
TRANSMITTER STATUS
Button added
Button removed
Remote control deleted
Memory full