Related Manuals for B&D SDO-3V2 Controll-A-Door S
Summary of Contents for B&D SDO-3V2 Controll-A-Door S
- Page 1 ® Controll-A-Door ® & PanelPro Sectional Door Opener Instruction Manual SDO-3V2 SDO-4V1 Controll-A-Door PanelPro ® ® Doc #: 161041_00 Part #:79151 Released: 04/08/2016...
-
Page 2: Table Of Contents
Controll-A-Door S & PanelPro Instruction Manual ® Table of Contents Installation Instructions 1. Installation Safety Warnings! 13. Auto-Close & Auxiliary Safety Beams 2. Before you Begin Auto Close Option Examine the conditions in the garage: Auxiliary Output Test the following before commencing installation: 4 14. -
Page 3: Installation Safety Warnings
Controll-A-Door S & PanelPro Instruction Manual ® 1. Installation Safety Warnings! This automatic garage door opener is designed and tested to offer safe service provided it is installed and operated in strict accordance with the following safety warnings. Failure to comply with the following instructions may result in death, serious personal injury or property damage. -
Page 4: Before You Begin
Controll-A-Door S & PanelPro Instruction Manual ® 2. Before you Begin Examine the conditions in the garage: a. Look at the ceiling: i. Is it plastered? The opener is mounted to a perforated angle which MUST be securely fastened to a structural support. You will need to locate the structural beams in the ceiling which are generally 400mm apart. -
Page 5: Kit Contents
Controll-A-Door S & PanelPro Instruction Manual ® 4. Kit Contents 1 x SDO drive unit 6. 1 x Wall bracket TS01 PLUS 2. 1 x Wall mount transmitter with battery 7. 1 x Door bracket Locator 15. 2 x Track Bracket and screws (CAD S Only) 8. -
Page 6: Fit The Opener
Controll-A-Door S & PanelPro Instruction Manual ® 6. Fit the Opener Secure C-Rail to Opener: a. Remove the Opener from the box and place onto towel. b. Locate and insert the shaft of drive unit into the C-Rail’s sprocket. c. Fix the two track brackets with four (4) M4 x 8 screws supplied in accessory pack. -
Page 7: Perforated Angle
Controll-A-Door S & PanelPro Instruction Manual ® 8. Perforated Angle (Not supplied) Attach Perforated Angle (not supplied) or equivalent a. Measure across the ceiling from the centre point 3177mm (+/- 150mm) to find a supporting beam. b. Create a perforated angle which best suits your site. Use a hack saw to cut the L shape metal strips. Secure the perforated angle to a supporting beam using diagrams shown below. -
Page 8: Mounting Brackets And Arms
Controll-A-Door S & PanelPro Instruction Manual ® 9. Mounting Brackets and Arms Mounting The Door Bracket: a. The door bracket locator is placed over the door bracket , on the door’s centre line one-third down the top panel and mounted using M6 or equivalent screws (not supplied), b. -
Page 9: Setting The Datum Position
Controll-A-Door S & PanelPro Instruction Manual ® 11. Setting the Datum Position NOTE: The door and shuttle must be engaged into the chain index. The door should be open approximately half way. NOTE: If Safety Beams are to be used they must be installed before setting the travel limits. -
Page 10: Safety Testing
Controll-A-Door S & PanelPro Instruction Manual ® 12. Safety Testing Test the Close Cycle CAUTION: Take care when completing a a. Press the OPERATE button to open the door. safety test. Failure to follow this warning b. If the door closes, press the OPERATE button to stop the door, then can result in serious personal injury and/or press OPERATE again to open. -
Page 11: Auto-Close & Auxiliary
Controll-A-Door S & PanelPro Instruction Manual ® 13. Auto-Close & Auxiliary Safety Beams WARNING! It is compulsory to have A Safety Beam Kit may be fitted to this opener. When this option is fitted, Safety Beams installed when using the operation of this device is such that if an object (i.e car, child etc) Auto-Close mode. -
Page 12: Coding A Transmitter
Controll-A-Door S & PanelPro Instruction Manual ® 14. Coding a Transmitter Storing the Transmitter Code The opener can only operated from remote control transmitters that have been programmed into its memory. Up to 64 codes can be stored in the memory. -
Page 13: Setting The Transmitter To Operate Pet Mode
Controll-A-Door S & PanelPro Instruction Manual ® 14. Coding a Transmitter Setting the Transmitter to Operate PET (Pedestrian) Mode The PET mode position (see Programming the Opener) must set prior to coding a transmitter. a. Press the DOOR CODE button five (5) times - the DOOR CODE LED will illuminate and the courtesy light will flash quicky (twice per second). -
Page 14: Home Owner Safety Warnings
Controll-A-Door S & PanelPro Instruction Manual ® 15. Home Owner Safety Warnings! This automatic garage door opener is designed and tested to offer safe service provided it is installed and operated in strict accordance with the following safety warnings. Failure to comply with the following instructions may result in death, serious personal injury or property damage. -
Page 15: Opener Safety & Security
Controll-A-Door ® 16. Opener Safety & Security Your Door CAN NOT be used by the opener when: WARNING! When operating the manual a. There is a locking device installed. release (while the door is open) the door b. There is a power failure. may fall rapidly due to weak or broken springs, or due to being improperly Your Door CAN be used when:... -
Page 16: User Operating Controls
Controll-A-Door S & PanelPro Instruction Manual ® 18. User Operating Controls Button Function 1. OPERATE Opens/stops/closes the door 2. CODING LED (Red) Flashes when a code is being stored or when the transmitter button is pressed 3. DOOR CODE (Blue) Is used for storing or erasing transmitter buttons for door operation 4. -
Page 17: Specifications
Controll-A-Door S & PanelPro Instruction Manual ® 20. Specifications Technical Specifications Controll-A-Door PanelPro ® ® Power supply 230V - 240Va.c. 50Hz 230V - 240Va.c. 50Hz Maximum door opening Width: 5500mm 4950mm Height: 2440mm 2440mm Door Area: 16.5m 13.5m Weight: 100kg 100kg Door must be well balanced and able to be operated by hand, as... -
Page 18: Troubleshooting
Controll-A-Door S & PanelPro Instruction Manual ® 21. Troubleshooting Symptom Possible cause Remedy The opener does not Garage door in poor condition e.g. Check the door’s operation work from the transmitter springs may be broken The opener does not have power Plug a device of similar voltage (e.g. - Page 19 Controll-A-Door S & PanelPro Instruction Manual ® 21 Troubleshooting Symptom Possible cause Remedy The SERVICE LED has A Fault has been detected. The fault Record opener function (How many beeps?) then started to flash and will be active each time an attempt is press the SET button once to reset the opener.
-
Page 20: Maintenance
Controll-A-Door S & PanelPro Instruction Manual ® 22. Maintenance Door Maintenance WARNING! Failure to maintain your garage A poorly maintained door could cause fatal / serious injuries or door may void the warranty on your garage damage to property. door opener. •... -
Page 21: Service Schedule
Controll-A-Door S & PanelPro Instruction Manual ® 25. Service Schedule Service Indicator (Only Available with CAD S) While the door opener does not require regular servicing, to function correctly the door must be in good operating condition. As a reminder the Controll-A-Door S has a built in maintenance ®... -
Page 22: Warranty
Controll-A-Door S & PanelPro Instruction Manual ® 26. Warranty Product: Controll-A-Door S and Panelpro ® ® Purchased from:______________________________Purchaser:___________________________________ (described as “you” below) Address:_____________________________________Installed by:__________________________________ Installed on (date):____________________________Invoice No:__________________________________ 1. MAKING A CLAIM - To make a warranty claim you must: is not of the type or condition defined in the Instruction Manual as suitable for a. -
Page 23: Optional Accessories
Controll-A-Door S & PanelPro Instruction Manual ® 27. Optional Accessories There are a range of additional accessories for your added convenience and security. Contact your Dealer for installation of these accessory items. • Safety Beams - Provides additional protection if the door is closing onto your property or person. - Page 24 Controll-A-Door S & PanelPro Instruction Manual ® Is your opener beeping or flashing? It may be time for a service (for more details see section 22) For a service, contact your dealer using the details below... Dealer: B&D Doors is a division of B&D Australia Pty Ltd ©...
Need help?
Do you have a question about the SDO-3V2 Controll-A-Door S and is the answer not in the manual?
Questions and answers
hi, I'm trying to reprogram for a new remote but the DOOR CODE button doesn't show any LCD light when I press it.
If the DOOR CODE button on the B&D SDO-3V2 Controll-A-Door S does not light up when pressed, try the following troubleshooting steps:
1. Check Power Supply – Ensure the opener is properly connected to a power source and receiving power.
2. Inspect for Damage – Look for any visible damage to the button or surrounding components.
3. Reset the Opener – Disconnect the power for a few minutes, then reconnect and try again.
4. Verify Compatibility – Ensure you are using a compatible Tri-Tran+ transmitter.
5. Erase and Reprogram Codes – If possible, follow the manual’s instructions to erase all programmed codes and reprogram the transmitter.
If the issue persists, consider contacting a professional for further inspection.
This answer is automatically generated