Table Of Contents - B&D PanelMax SDO-8V3 Installation Instructions Manual

PanelMax installation instructions
Contents
Important Safety Warnings
1. Safety Warnings!
Installation Instructions
2. Before you Begin
3. Tools Required
4. Kit Contents
5. Position
6. Fit the Opener
7. Bracket Position
8. Perforated Angle
9. Mounting Brackets and Arms
10. Optional Safety Beam Kit
10.1 Inserting batteries into receiver and transmitter
10.2 Assemble the Mounting Bracket
10.3 Mounting the Bracket
10.4 Aligning the Transmitter and Receiver
11. Specifications
12. Setting Limits
12.1 Set the Limit Positions and adjust drive speed:
12.2 Clearing the Door Limit Positions
12.3 Re-profiling the Door
12.4 Controller memory reset
13. Safety Testing
13.1 Test the Close Cycle
13.2 Testing the Open Cycle
13.3 Test the Manual Door Operation
14. Auto-Close
14.1 Auto-Close
14.2 Terminal Block
14.3 Connecting or Disconnecting Accessories
WARNING! IMPORTANT SAFETY INSTRUCTIONS
FOLLOW ALL INSTRUCTIONS SINCE INCORRECT INSTALLATION CAN LEAD TO SEVERE INJURY.
• before installing the drive, remove all unnecessary ropes or chains and disable any equipment, such as locks, not needed for
powered operation;
• before installing the drive, check that the door is in good mechanical condition, correctly balanced and opens and closes
properly;
• install the actuating member for the manual release at a height less than 1,8 m;
• install any fixed control at a height of at least 1,5 m and within sight of the door but away from moving parts;
• permanently fix the labels warning against entrapment in a prominent place or near any fixed controls;
• permanently fix the label concerning the manual release adjacent to its actuating member;
• after installation, ensure that the mechanism is properly adjusted and that the drive reverses when the door contacts a 40 mm
high object placed on the floor.
• necessary information for the safe handling of a drive weighing more than 20 kg. This information shall describe how to use the
handling means, such as hooks and ropes;
• the drive must not be used with a door incorporating a wicket door (unless the drive cannot be operated with the wicket door
open);
• after installation, ensure that parts of the door do not extend over public footpaths or roads.
• vertical doors and gates need an anti-drop feature or device;
• information if a hazardous part of the drive is intended to be installed at a height of at least 2.5 m above floor level or other access
level;
• except for horizontally moving pedestrian doors, ensure that entrapment due to the opening movement of the driven part is
avoided
15. Coding a Transmitter
3
15.1 Storing the Transmitter Code
15.2 Remotely Coding Transmitters
5
15.3 Erasing All Transmitter Codes
5
15.4 Vacation Mode
15.5 Installing the Wall Mounted Transmitter
6
6
Home Owner Instructions
7
16. Opener Safety & Security
7
16.1 Your Door CAN NOT be used by the opener when:
8
16.2 Your Door CAN be used when:
8
16.3 To Disengage the Opener:
9
16.4 To Re-engage the Opener:
9
17. Operating your Opener
9
18. User Operating Controls
9
19. Troubleshooting
9
20. After Installation Care
10
20.1 Service Checklist
11
20.2 Battery Replacement
11
20.3 Battery Disposal
12
20.4 Warranty
12
21. Appendix
12
A - Status Indication during Operating Mode.
13
B - Adjustment Mode Instructions
13
C - Adjusting Force Margins
13
D - Battery Functions
13
E - Setting the PET mode position
14
F - Setting Limits via Transmitter
14
G - Setting up Tilt Door
15
15
2
16
16
16
17
17
17
18
18
18
18
18
18
19
20
22
22
23
23
23
24
24
25
26
26
26
27
28