Related Manuals for MicroPower SHARP 10
Summary of Contents for MicroPower SHARP 10
- Page 1 SHARP 10 USER MANUAL 'ONLINE VERSION' Battery charger Valid for Sharp with Model Code: 1A1A2**, 2A199**, 2A1A0**, 2A1A4**...
-
Page 2: Table Of Contents
Contact information..............................10 Figures..................................11 P2 - fig. 1a.................................. 11 P3 - fig. 1b.................................. 11 P1 - fig. 1c.................................. 11 P2 - fig. 2..................................12 P3 - fig. 3..................................12 P1 - fig. 4..................................13 Approvals..................................14 SHARP 10 - EU Declaration of Conformity........................ 14... -
Page 3: Safety
SHARP 10 - User manual 'online version' Safety Safety precautions Read the instructions. The manual contains important safety and operating instructions. Always keep this manual nearby the product. Read and understand this instruction, the battery instruction provided by your battery manufacturer, and your employer’s safety practice, before using, installing, or servicing the product. -
Page 4: Warning Information
SHARP 10 - User manual 'online version' Incorrect settings of the battery charger may damage the battery and generate explosive gases from the battery • during charging. Always check settings before start charging. Do not charge non-rechargeable batteries, damaged batteries or battery types not intended for the charger. -
Page 5: Graphical Symbols
SHARP 10 - User manual 'online version' WARNING Indicates a potentially dangerous situation. Death or serious injury may occur if appropriate precautions are not taken. CAUTION Indicates a situation where damage or injury could occur. If it is not avoided, minor injury and/or damage to property may result. -
Page 6: Description
Maintenance personnel and technicians • Description Sharp 10 is a regulated battery charger, available in different designs, for charging either flooded or valve-regulated lead-acid batteries. The battery charger is supplied with a pre-set charging curve adapted for the battery type specified on order. -
Page 7: Charging
SHARP 10 - User manual 'online version' 1. Fuse 2. Battery cables 3. Mains cable 4. LED indication Charging WARNING High voltage! Do not use the battery charger if it is damaged. Disconnect the mains immediately. Do not touch damaged parts, uninsulated battery terminals, connectors, or other live electrical parts. - Page 8 SHARP 10 - User manual 'online version' Mains power supply not connected. Charging complete. Main charging in progress. Equalizing charge in progress. Battery not connected. Defective battery fuse. Battery voltage too high. Battery voltage too low. Simultaneous flashing. Battery charger is too hot. Alternate flashing.
-
Page 9: Maintenance And Troubleshooting
SHARP 10 - User manual 'online version' Maintenance and troubleshooting WARNING High voltage! Only qualified personnel should install, use, maintain and service this product. Disconnect the battery and power supply before maintenance, servicing or dismantling. WARNING High voltage! Do not use the battery charger if it is damaged. Disconnect the mains immediately. -
Page 10: Recycling
SHARP 10 - User manual 'online version' Battery types: Lead-acid Output voltage: See data label Recommended battery capacity: 24V/11A: 35–200 Ah 24V/8A: 30–180 Ah 24V/4A: 15–90 Ah 12V/17A: 50–220 Ah 12V/10A: 35–200 Ah Efficiency: > 90 % at full load Ingress protection: IP65 Approvals: CE and/or UL. -
Page 11: Figures
SHARP 10 - User manual 'online version' Figures P2 - fig. 1a P3 - fig. 1b P1 - fig. 1c... -
Page 12: P2 - Fig. 2
SHARP 10 - User manual 'online version' P2 - fig. 2 P3 - fig. 3... -
Page 13: P1 - Fig. 4
SHARP 10 - User manual 'online version' P1 - fig. 4... -
Page 14: Approvals
SHARP 10 - User manual 'online version' Approvals SHARP 10 - EU Declaration of Conformity...