Titan TTCSP49 Manual
  1. Manuals
  2. Brands
  3. Titan Manuals
  4. Chainsaw
  5. TTCSP49
  6. Manual

Titan TTCSP49 Manual

Petrol chain saw (49.3 cm3)
Hide thumbs
Table of Contents

Advertisement

Quick Links

Petrol Chain Saw
(49.3 cm
)
3
TTCSP49
EAN: 5059340255989
BX220IM/B3
WARNING: Read the instruction handbook thoroughly before
using the product. First time operators should receive practical
use instructions of the product and protective equipment from
an experienced operator.

Advertisement

Table of Contents
loading

Related Manuals for Titan TTCSP49

Summary of Contents for Titan TTCSP49

  • Page 1 Petrol Chain Saw (49.3 cm TTCSP49 EAN: 5059340255989 BX220IM/B3 WARNING: Read the instruction handbook thoroughly before using the product. First time operators should receive practical use instructions of the product and protective equipment from an experienced operator.

  • Page 2: Table Of Contents

    TTCSP49 Let’s get started... These instructions are for your safety. Please read through them thoroughly before use and retain them for future reference. Getting Started... Safety information Your product Technical specifications Before start Quick start more detail... Product functions Operation...

  • Page 3: Safety Information

    Safety information TTCSP49 Safety warnings 1. This product is not intended for use by children and persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge. 2. Children should be supervised to ensure that they do not play with the product.
  • Page 4 Safety information TTCSP49 > Do not under any circumstances modify the product. Modifications can result in serious personal injury or death. > Do not start cutting until you have a clear work area and secure footing. > All product servicing and maintenance, other than the items listed in this manual, should be performed by an authorised service centre.
  • Page 5 Safety information TTCSP49 > Fuel vapour pressure may build up inside the fuel tank depending on the fuel used, weather conditions and the tank venting system. To reduce the risk of burns and other personal injuries, remove the fuel tank cap carefully to allow any pressure build up to release slowly.
  • Page 6 Safety information TTCSP49 Operation > When sawing ensure the product does not touch any foreign materials such as rocks, fences, nails etc. Such objects may be flung out and could result in damage to the product, serious or even fatal injuries.
  • Page 7 Safety information TTCSP49 Transport and storage > Stop the engine and engage the chain brake before transporting the product. > Carry the product with the engine stopped, the guide bar and saw chain to the rear, and the exhaust away from the body.
  • Page 8 Safety information TTCSP49 > Only use replacement bars and chains specified by the manufacturer. Incorrect replacement bars and chains may cause chain breakage and/or kickback. > Follow the manufacturer’s sharpening and maintenance instructions for the saw chain. Decreasing the depth gauge height can lead to increased kickback.
  • Page 9 Safety information TTCSP49 Residual risks Even if you are operating this product in accordance with all the safety requirements, potential risks of injury and damage remain. The following dangers can arise in connection with the structure and design of this product: >...
  • Page 10 Safety information TTCSP49 Description of signal words: The signal word that indicates a hazard with a high level of risk DANGER! which, if not avoided, will result in death or serious injury. The signal word that indicates a hazard with a medium level of WARNING! risk which, if not avoided, could result in death or serious injury.
  • Page 11 Safety information TTCSP49 Hot surface, do not touch! High temperatures on the product’s surfaces and structural parts that could cause burns, if they are touched. The product can also stay hot for a longer period of time after the operation! Petrol engines produce toxic carbon monoxide exhaust fumes.
  • Page 12 Safety information TTCSP49 Choke – CLOSE position. PULL to close Primer Objects thrown by the product could hit the operator or other bystanders. Always ensure that other people and pets remain at a safe distance from the product when it is in operation. In general, children must not come near the area where the product is operating.

  • Page 13: Your Product

    Your product TTCSP49 1. Lubrication hole (on both sides) 11. Stop switch 2. Guide bar 12. Fuel tank cap 3. Saw chain 13. Adjusting screws for carburetor 4. Front hand guard (with chain brake) 14. Recoil starter handle 5. Front handle (for left hand) 15.
  • Page 14 Your product TTCSP49 Content of delivery 22. Chain oil flow adjuster 25. Fuel mixing bottle 23. Main unit 26. Guide bar cover 24. Multi-tool 27. File 28. Screwdriver...

  • Page 15: Technical Specifications

    Technical specifications TTCSP49 Technical specifications General Dimensions: > approx. 425 x 240 x 275 mm > Product without guide bar, saw chain and empty tank: approx. 5.54 kg > Machine with guide bar, saw chain and empty tank, in normal operating configuration: approx.
  • Page 16 Technical specifications TTCSP49 Sound emission level > Sound pressure level at operator position: 99.68 dB(A) > Measured sound power level L 119.58 dB(A) > Uncertainty K: 3.0 dB(A) > Guaranteed sound power level L (acc. to 2000/14/EC amended by 2005/88/EC): 115 dB(A) Vibration emission level >...

  • Page 17: Before You Start

    Before you start TTCSP49 Unpacking 1. Unpack all parts and lay them on a flat, stable surface. 2. Remove all packing materials and protective shipping materials, if applicable, including the protective cover on the spiked bumper (16). 3. Make sure the delivery contents are complete and free of any damage. If you find that parts are missing or show damage do not use the product and contact your dealer.
  • Page 18 Before you start TTCSP49 Assembly WARNING! The product must be fully assembled before operation! Do not use a product that is only partly assembled or assembled with damaged parts! Follow the assembly instructions step-by-step and use the pictures provided as a visual guide to assemble the product easily! Disconnect the spark plug connector before assembly! Reconnect it after assembly (see "Maintenance").
  • Page 19 Before you start TTCSP49 1. Pull the front hand guard (4) backwards to disengage the chain brake (Fig. 1). 2. Loosen the fixing nuts (18) using the multi-tool (24) and remove the clutch cover (20) (Fig. 2). Ensure the spiked bumper (16) is properly fixed to the product. Tighten the 2 bolts...
  • Page 20 Before you start TTCSP49 3. Place the slot on the guide bar (2) over the 2 bolts (step 1, Fig. 3). 4. Push the guide bar (2) to the left towards the drive sprocket (step 2, Fig. 3). 5. Place the saw chain (3) over the drive sprocket (behind the clutch) and fit around the nose sprocket at the tip of the guide bar (2) in the correct direction (Fig.
  • Page 21 Before you start TTCSP49 7. Refit the clutch cover (20) and fasten using the fixing nuts (18) and the multi-tool (24). To fit the clutch cover, align the tensioner pin with the lower hole on the guide bar (2) by turning the chain tension adjuster (19) clockwise or anti-clockwise with the multi- tool (24) (Fig.
  • Page 22 Before you start TTCSP49 WARNING! Disconnect the spark plug connector before adjusting saw chain tension! The cutting edges of the saw chain are sharp! Always wear protective gloves when handling chain! Always maintain proper chain tension! A loose chain increases the risk of...
  • Page 23 Before you start TTCSP49 Chain lubrication WARNING! The product is not filled with chain oil. It is essential to fill the product with chain oil before using it! Never operate the product without chain oil as this will result in extensive damage to the product! Operating the saw...
  • Page 24 Before you start TTCSP49 4. Wipe up spilled saw chain oil with a soft cloth. Refit and screw the oil tank cap (15) firmly (Fig. 10). NOTE: Always dispose of used saw chain oil and objects contaminated with them in accordance with local regulations.
  • Page 25 Before you start TTCSP49 Filling up fuel and oil WARNING! This product is not supplied with petrol-oil mixture in the engine! Before operating this product it is essential to fill it with petrol-oil mixture! This product is equipped with a 2-stroke engine, the fuel and oil tank are combined and it is essential to fill a fuel-oil mixture before operating this product.
  • Page 26 Before you start TTCSP49 4. Unscrew and remove the fuel tank cap (12) (Fig. 14). 5. Fill the fuel and oil mixture into the fuel tank. Leave approximately 5 mm of space between the top of the fuel and the inside edge of the tank to allow for expansion.

  • Page 27: Quick Start

    Quick start TTCSP49 Operating controls Front hand guard Choke knob Recoil starter handle Oil tank cap Primer Throttle trigger lock-out Fuel tank Throttle trigger Stop switch Chain oil flow adjuster...
  • Page 28 Quick start TTCSP49 Preparation Add fuel and oil Assemble Adjust Add chain oil mixture Starting Engage the Set stop switch Fully pull Press primer Pull recoil chain brake to I position choke knob 6 times starter handle 4 times Fully press in...
  • Page 29 Quick start TTCSP49 Stopping Set stop switch to O Release throttle trigger Engage the chain brake position and throttle trigger lock- Storage Empty fuel tank Empty oil Clean and maintain Store WARNING! This quick start provides only a short overview of how to start...

  • Page 30: In More Detail

    Product functions TTCSP49 Intended use This petrol chain saw TTCSP49 is designated with a power output of 2.1 kW. The product is intended for cutting logs and limbs with a thickness of max. 49.3 cm (see “Technical specifications”). WARNING! The product must be used by an experienced operator* having...
  • Page 31 Product functions TTCSP49 Safety equipment The product has several pieces of safety equipment which reduce the risk of injury when working (Fig. 16): Throttle trigger Chain brake / lock-out front hand guard Chain catcher...
  • Page 32 Product functions TTCSP49 Chain brake / front hand guard The front hand guard (4) is a safety mechanism that stops the saw chain (3) immediately when it is pushed towards the operator in case of a kickback. The chain brake is a safety mechanism activated by the front hand guard (4). When kickback occurs, the saw chain stops immediately.

  • Page 33: Operation

    Product functions / Operation TTCSP49 Throttle trigger lock-out The throttle trigger lock-out (8) prevents unintentional activation of the throttle trigger (10). The throttle trigger can only be activated if the throttle trigger lock-out is pressed. Chain catcher The chain catcher (17) is intended to catch a torn saw chain (3) or saw chain which has jumped out of the guide bar (2).
  • Page 34 Operation TTCSP49 Starting the engine DANGER! Risk of fire! > Due to any spilled fuel, the product can catch fire. > Wipe any spilled fuel up before starting. > Start the engine a few metres away from the place where you have filled it.
  • Page 35 Operation TTCSP49 6. Hold the product securely to the ground. Place your left hand on the front handle (5) and additionally secure the product with your right foot (Fig. 22). 7. Pull the recoil starter handle (14) slowly with your right hand until you feel a definite resistance and then give it a brisk, strong pull.
  • Page 36 Operation TTCSP49 After starting the engine 1. Leave the engine running at idling speed for a while. 2. Slowly press down on the throttle trigger (10) to increase the engine speed. The clutch will be released when the engine speed is high enough, and the saw chain (3) will start to rotate.
  • Page 37 Operation TTCSP49 4. Check the proper lubrication as described in section “Before you start - Chain lubrication” before performing any cut. 5. Ensure the saw chain (3) is running at full speed before it makes contact with the wood. Use the spiked bumper (16) to secure the product onto the wood before starting to cut and use it as a leverage point while cutting (Fig.
  • Page 38 Operation TTCSP49 Kickback WARNING! Beware of kickback! Kickback can lead to dangerous loss of control of the product and result in serious or fatal injury to the operator or anyone standing close by! Always be alert because rotational kickback and pinch...
  • Page 39 Operation TTCSP49 5. Keep a good firm grip on the product with both hands, the right hand on the rear handle (9) and the left hand on the front handle (5), when the engine is running. Maintain a firm grip with your thumbs and fingers encircling the handles. A firm grip will help you reduce “kickback”...
  • Page 40 Operation TTCSP49 Felling a tree 1. When bucking and felling operations are being performed by two or more persons at the same time, the felling operations should be separated from the bucking operation by a distance of at least twice the height of the tree being felled. Trees should not be felled in a manner that would endanger any person, strike any utility line or cause any property damage.
  • Page 41 Operation TTCSP49 Felling back cut 1. Make the felling back cut (Fig. 31, A) at least 50 mm higher than the horizontal notching cut (Fig. 31). Keep the felling back cut parallel to the horizontal notching cut. Make the felling back cut so enough wood is left to act as a hinge. The hinge (Fig.
  • Page 42 Operation TTCSP49 WARNING! Never climb into a tree to limb or prune! Do not stand on ladders, platforms, logs, or in any position which may cause you to lose the balance or control of the saw! When pruning trees, it is important not to make the flush cut...
  • Page 43 Operation TTCSP49 3. When the log is supported on both ends (Fig. 35), cut 1/3 the diameter from the top (overbuck). Then make the finished cut by underbucking the lower 2/3 to meet the first cut. 4. When bucking on a slope always stand on the uphill side of the log (Fig. 36). When “cutting through”, to maintain complete control release the cutting pressure near the...
  • Page 44 Operation TTCSP49 Freeing a trapped saw It the saw becomes trapped during cutting, operators should a) switch off the saw and attach it securely to the tree inboard (i.e. towards the trunk side) of the cut or to a separate tool line,...

  • Page 45: Care And Maintenance

    Care and maintenance TTCSP49 The golden rules for care WARNING! Always stop the engine, disconnect the spark plug connector and let the product cool before performing inspection, maintenance and cleaning work. DANGER! Proper maintenance is essential for safe and trouble free operation.
  • Page 46 Care and maintenance TTCSP49 Cleaning the guide bar > Disassemble the guide bar (2) and saw chain in reversed order from assembly. > Remove any dirt accumulated inside the guide bar slot using the putty knife (not provided) (Fig. 39).
  • Page 47 Care and maintenance TTCSP49 clean every 10 hours of operation or whenever necessary Nose sprocket lubricate every 10 hours of operation or whenever necessary Clutch lubricate every 25 hours of operation or whenever necessary housing check Chain catcher replace whenever necessary...
  • Page 48 Care and maintenance TTCSP49 Sprocket wheel 1. Clean the sprocket wheel. 2. Using a disposable lube gun, insert the needle nose into the lubrication hole (1) and inject grease until it appears at the outside edge of the sprocket (Fig. 40).
  • Page 49 Care and maintenance TTCSP49 NOTE: The condition of the oil passages can be easily checked. If the passages are clear, the chain will automatically give off a spray of oil within seconds of the product starting. Your product is equipped with an automatic oiling system.
  • Page 50 Care and maintenance TTCSP49 Saw chain sharpening NOTE: Never saw with a blunt chain. The saw chain is blunt if you have to push the product into the tree and the chips are very small. 1. Have the saw chain (3) sharpened professionally at an authorised service centre or sharpen the chain yourself by using the file (27).
  • Page 51 Care and maintenance TTCSP49 4. Use the chain file (27), with diameter 1.1 times the cutting tooth depth. Make sure 20 % of the file diameter is above the cutter’s top plate. 5. File at an angle perpendicular to the bar, and at an angle of 25° to the direction of travel (Fig.
  • Page 52 Care and maintenance TTCSP49 Air filter Inspect the air filter (6b) regularly. Clean or replace it with a new one if necessary. 1. Loosen the fixing screw and remove the top cover (6) (Fig. 47). 2. Remove the air filter (6b).
  • Page 53 Care and maintenance TTCSP49 Spark plug NOTE: For good performance, the spark plug must be properly gapped and free of deposits. Inspect the spark plug every 25 hours or before long-term storage over 180 days. Clean or replace with a new one if necessary (type: CHAMPION RCJ7Y).
  • Page 54 Care and maintenance TTCSP49 4. Check the spark plug for damage and wear. The colour of the ground electrode should be light- Spark plug brown. 5. Remove the deposits from the electrode with a soft wired brush. Avoid heavy cleaning of the electrode.
  • Page 55 Care and maintenance TTCSP49 Idle speed screw WARNING! Adjusting the screws L and H must be performed by an authorised service centre or a similarly qualified person. Using a single D screwdriver (not provided) turn the screws L and H to adjust the quantity of fuel in relation to the air.
  • Page 56 Care and maintenance TTCSP49 Repair This product does not contain any parts that can be repaired by the consumer. Contact an authorised service centre or a similarly qualified specialist to have it checked and repaired. Storage WARNING! Risk of injury! Make sure that unauthorized persons do not have...
  • Page 57 Care and maintenance TTCSP49 Long term storage NOTE: Risk of product damage! > If you are not going to be using the product for a while, remove the fuel and saw chain oil from the product. This way, you will prevent a gumming-up of the engine and of the grease pump.

  • Page 58: Troubleshooting

    Troubleshooting TTCSP49 Troubleshooting Suspected malfunctions are often due to causes that the operators can fix themselves. Therefore check the product using this section. In most cases, the problem can be solved quickly. WARNING! Only perform the steps described in these instructions! All further...
  • Page 59 Troubleshooting TTCSP49 Problem Possible cause Solution Engine does Air filter is soiled? Clean the air filter. not reach Incorrect fuel or incorrect Stop the engine, empty tank, the maximum mixture? then fill up with the correct speed. mixture of fuel to oil (40:1).

  • Page 60: Recycling And Disposal

    Recycling and disposal / Guarantee TTCSP49 Recycling and disposal 1. Old equipments are potentially recyclable and do not, therefore, belong in your household rubbish. You are requested to assist us and our contribution to saving resources and protecting the environment by handing in this equipment to an equipped collection centre (if there is one available).

  • Page 61: Customer Care And Technical Helpline

    Customer care and technical helpline TTCSP49 Customer care and technical helpline A better way to repair your tools Kingfisher takes special care in creating high-quality garden power tools that are designed to last. But if a fault develops with your garden power tool and you need to claim under...

  • Page 62: Availability Of Spare Parts

    Availability of spare parts TTCSP49 Availability of spare parts Contact the customer service helpline for assistance or visit www.kingfisherspares.com For assistance contact the customer services helpline: UK: 0800 0789647 uk@Kingfisherservice.com EIRE: 1800 932226 eire@kingfisherservice.com Further information about this product can also be found at:...

  • Page 63: Declaration Of Conformity

    UK declaration of conformity TTCSP49 (UK) DECLARATION OF CONFORMITY Product > Chain saw > TTCSP49 > 49.3 cm , 2.1 kW > 000001 - 999999 Name and address of the manufacturer or his authorised representative: Kingfisher International Products Limited 3 Sheldon Square...

  • Page 64: Eu Declaration Of Conformity

    EU declaration of conformity TTCSP49 (EN) EU DECLARATION OF CONFORMITY (FR) DÉCLARATION UE DE CONFORMITÉ (PL) DEKLARACJA ZGODNOŚCI UE (RO) DECLARAȚIA DE CONFORMITATE UE (ES) DECLARACIÓN UE DE CONFORMIDAD (PT) DECLARAÇÃO DE CONFORMIDADE UE Product/ Produit/ Produkt/Produsul/Producto/Produto > Chain saw/Tronçonneuse/Pilarka łancuchowa/Motoferastrau/Motosierra/Motosserra >...
  • Page 65 EU declaration of conformity TTCSP49 The object of the declaration described above is in conformity with the relevant Union harmonisation legislation: L’objet de la déclaration décrit ci-dessus est conforme à la législation d’harmonisation de l’Union applicable: Wymieniony powyżej przedmiot niniejszej deklaracji jest zgodny z odnośnymi wymaganiami unijnego prawodawstwa harmonizacyjnego: Obiectul declarației descris mai sus este în conformitate cu legislația relevantă...
  • Page 66 EU declaration of conformity TTCSP49 Measured Sound Power Level/ Niveau de puissance acoustique mesuré/ Zmierzony poziom mocy akustycznej/ Nivel de putere acustică măsurat/ Nivel de potencia sonora medido / Nível de potência sonora medido: 111.47 dB(A) Guaranteed Sound Power Level/ Niveau de puissance acoustique garanti/ Gwarantowany poziom mocy akustycznej/ Nivel de putere acustică...
  • Page 67 Manufacturer, Fabricant, Prodecent, Producător, Fabricante: UK Manufacturer: Kingfisher International Products Limited 3 Sheldon Square London W2 6PX United Kingdom EU Manufacturer: Kingfisher International Products B.V. Rapenburgerstraat 175E 1011 VM Amsterdam The Netherlands www.diy.com www.screwfix.com www.screwfix.ie To view instruction manuals online, visit www.kingfisher.com/products...

This manual is also suitable for:

5059340255989

Table of Contents