Recommended Rivet/Die/Stack-Up; Application Of The Die Sets - Pro Spot PR-8 Instruction Manual

4 .0
• This device includes 12 dies: PRR-10, PRR-11, PRR-12, PRR-13, PRR-14(2),
PRR-15, PRR-16, PRR-17, SA-0400, SA-0401, SA-0402
• TIGHTEN THREADS FULLY TO OR DAMAGE TO DIE/PISTON RAM THREADS WILL OCCUR!
During use, the pressure must not be on the threads of the dies. They must be firmly seated or they
could break during operation .
• Never operate the rivet gun without any material between the clamps . Operating the rivet gun without
metal between the dies will cause damage to the punch and die . Do not operate or charge the rivet gun
or batteries in a dust filled environment.
• Choose the correct punch and die set for the application .

4.1 Recommended Rivet/Die/Stack-up

The following table shows the recommended rivet and die combination for given joint stack-ups:
• This device includes 12 dies: PRR-10,
• TIGHTEN THREADS FULLY TO OR DAMAGE TO DIE/PISTON RAM THREADS WILL
• Never operate the rivet gun without any material between the clamps. Operating the
• Choose the correct punch and die set for the application.
0402
4.1 Recommended Rivet/Die/Stack-up
0.9
The following table shows the recommended rivet and die combination for given joint stack-ups:
0.9
0.9
Min. Total Stack-up
(mm)
4.1
For Instructional Videos:
https://www.youtube.com/c/Prospotwelding
6.0
7.5
MODULAR C-ARM ATTACH & REMOVE
5.0

5.0 Application of the Die Sets

APPLICATION OF THE DIE SETS
Bad
Bad
PRR-11, PRR-12, PRR-13, PRR-14(2),
PRR-15, PRR-16, PRR-17, SA-0400,
SA-0401, SA-0402
OCCUR! During use, the pressure must not be on the threads of the dies. They
Non-fully tightened
rivet dies will result
must be rmly seated or they could break during operation.
in damage to ram threads
rivet gun without metal between the dies will cause damage to the punch and
die. Do not operate or charge the rivet gun or batteries in a dust lled environment.
4.1 Recommended Rivet/Die/Stack-up
Min. Total
Stack-up (mm)
The following table shows the recommended rivet and die combination for given jo
4.1
6.0
7.5
Min. Top Sheet
Thickness (mm)
Max Total Stack-up
0.9
(mm)
0.9
0.9
5.9
All Info Copyright © Pro Spot International Inc.
7.1
11.0
APPLICATION OF THE DIE SETS
• This device includes 12 dies: PRR-10,
Good
PRR-11, PRR-12, PRR-13, PRR-14(2),
PRR-15, PRR-16, PRR-17, SA-0400,
SA-0401, SA-0402
• TIGHTEN THREADS FULLY TO OR DAMAGE TO DIE/PISTON RAM
OCCUR! During use, the pressure must not be on the thread
must be rmly seated or they could break during operation.
• Never operate the rivet gun without any material between the clam
rivet gun without metal between the dies will cause damage
die. Do not operate or charge the rivet gun or batteries in a d
• Choose the correct punch and die set for the application.
Max Total Pro Spot
Stack-up (mm) Rivet P/N
5.9 PRR-5-6mm
7.1 PRR-5-8mm
11.0 PRR-5-10mm
Min. Total Stack-up
(mm)
Pro Spot
4.1
Rivet P/N
6.0
7.5
PRR-5-6mm
PRR-5-8mm
PRR-5-10mm
Good
Pro Spot Forming
Die P/N
0401
0401
0402
Max Total Stack-up
(mm)
Pro Spot Forming
5.9
Die P/N
7.1
11.0
0401
0401
0402
Good
Pro Spot Pro S
Rivet P/N
PRR-5-6mm
PRR-5-8mm
PRR-5-10mm
10