Table of Contents
Advertisement
IUM_WIZARDX_03_22_EN
The unit must be installed in an area where access is only permitted to OPERATORS, MAINTENANCE PERSONNEL and
TECHNICIANS. If this is not possible, it must be enclosed in a perimeter fence positioned at least two metres from the external
surfaces of the machine itself.
The staff of the INSTALLER or any other visitors must always be accompanied by an OPERATOR. For no reason whatsoever must
non-authorised persons be left on their own with the unit.
MAINTENANCE TECHNICIANS must only work on the controls of the unit. They should not open any panels, other than the access
panel to the control module. The INSTALLER must limit him/herself to connecting the plant to the unit.
Access the unit using the relative personal protective equipment and only after having read and understood the documents and
instructions, which must always be kept close at hand.
This product and the relative documents, including this manual, are intended for people who have received independent training and
have been taught how to work in a correct and safe manner. Before handling this equipment in any way, it is essential that the
personnel involved have read and understand all the manuals and all the other reference material. The personnel must also be
familiar with and observe the standards that apply to the work in hand.
The manufacturer, during design and construction, has paid particular attention to aspects that may pose a risk to the safety and
health of people interacting with the machine. The manufacturer has complied with the applicable laws as well as the code of good
manufacturing practice. The purpose of this manual is to encourage users to take all due care and thereby avoid any risks. In any
case, prudence is required at all times. Safety is also the responsibility of all operators who interact with the machine.
Carefully read the instructions in this manual and those applied directly on the machine, and respect those concerning safety in
particular.
An overall project that envisages implementation of this machine in a system must take into account the code of good practice as
well as the legislative and regulatory aspects. Particular attention must be paid to all the recommendations and technological
information provided by the manufacturer. Do not tamper with, avoid, remove or bypass the safety devices installed on the machine.
Failure to observe this requirement could result in serious risks to the health and safety of the persons involved.
The personnel who carry out any kind of work during the entire life span of the machine must have precise technical knowledge,
special skills and recognised experience in the specific sector. Non-fulfilment of these requirements could endanger people's health
and safety.
Keep the area around the machine in a good state in order to avoid risks to the health and safety of persons during normal use and
maintenance of the machine.
Some processes may require the assistance of one or more helpers. In which case, these helpers must be duly trained and informed
of the type of work to be carried out in order to avoid risks to their health and safety.
Move the machine observing the information shown on the packaging and the instructions on use provided by the manufacturer.
When handling, if the circumstances demand it, request the assistance of one or more helpers who can give directions.
The personnel who carry out loading, unloading and handling of the equipment must have recognised skills and experience in the
specific sector and must have absolute command of the lifting equipment to be used.
During installation, observe the clearances indicated by the manufacturer and take into account all the work activities carried out in
the vicinity. Installation must also be carried out in compliance with the laws in force on safety at work.
The machine must be installed and connected in accordance with the manufacturer's instructions. The person in charge must also
take into account all regulatory and legislative requirements, carrying out all installation and connection operations in a workmanlike
manner.
After installation and before commissioning the machine, he must perform a general check to make sure that these requirements
have been met.
Check that any means of transport to be used for transfer of the machine are suitable for the purpose, and that the machine is loaded
and unloaded with care to ensure the safety of the operator and of any other persons who are directly involved. Before transfer,
make sure that the machine and its components are duly anchored to the vehicle and do not exceed the maximum permitted
dimensions for transport on the vehicle. Apply any necessary signs.
The operator must have read and understood the information on use of the machine, and have suitable skills and experience for
carrying out the work in hand.
Put the machine only to the uses foreseen by the manufacturer. Improper use of the machine may pose risks to the health and safety
of the persons and cause financial losses.
9
Advertisement
Table of Contents
