Download
Share
Print this page
  1. Manuals
  2. Brands
  3. ADAPT SOLUTIONS Manuals
  4. Automobile Accessories
  5. XL-SEAT XLS-DAKC05L
  6. Installation manual

ADAPT SOLUTIONS XL-SEAT XLS-DAKC05L Installation Manual

For dodge dakota club cab 2005-2011
Hide thumbs
1
2
3
4
5
6
7
8
9

Advertisement

Quick Links

Download this manual
XL-SEAT
INSTALLATION MANUAL
XLS-DAKC05L
DODGE DAKOTA CLUB CAB 2005-2011
DRIVER

Advertisement

loading
Need help?

Need help?

Do you have a question about the XL-SEAT XLS-DAKC05L and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for ADAPT SOLUTIONS XL-SEAT XLS-DAKC05L

Summary of Contents for ADAPT SOLUTIONS XL-SEAT XLS-DAKC05L

  • Page 1 XL-SEAT INSTALLATION MANUAL XLS-DAKC05L DODGE DAKOTA CLUB CAB 2005-2011 DRIVER...
  • Page 2 1- Remove the two (2) doorstep moldings. Unbolt the seat belt reel from the doorstep. NOTE: You do not need to remove the plastic cover that covers the seat belt reel. Disconnect the wire from the seat belt reel. Unbolt the two (2) back bolts of the seat. 2- Disconnect and then lengthen the seat belt reel wire.
  • Page 3 4- Bolt the seat belt reel to the floor adaptor. Use two (2) 7/16” X 3/4” grade 8 bolts. 5- Install the XL-SEAT onto the floor adaptor. Secure the unit in place using four (4) 7/16” X 3/4” flat head bolts. Attach the motor using a 1/2” X 1 1/4” shoulder bolt. 6- Proceed with the installation of the electrical wiring for the XL-SEAT.
  • Page 4 9- Install the XL-SEAT transfer board. NOTE: The XL-SEAT transfer board has adjustment if needed. Lift off the cushion. Unbolt the four (4) flat head bolts and relocate the board to the desired position and secure it in place using the four. Once you have completed reinstall the cushion.
  • Page 5 ELECTRICAL INSTALLATION FOR XL-SEAT 1. Thread the lead power cable (red +) under the doorstep moulding and thru the firewall. WARNING: Pass thru a grommet in the firewall to prevent the cable from chaffing. 2. Install the circuit breaker near the battery and then connect the battery to the circuit breaker.
  • Page 6 ELECTRICAL BOX CONNECTIONS XL-SEAT ALONE CTRL BOX: EW-CBX-01 PENDANT: EW-CON-04 RED = 12V POWER SUPPLY BLACK = GROUNDED TO THE CHASSIS GREY WIRE TO THE PENDANT TWO YELLOW WIRES RED = 12V POWER SUPPLY BLACK = GROUNDED TO THE TO THE XL-SEAT ACTUATOR CHASSIS XL-SEAT 2005-2011 DODGE DAKOTA CLUB CAB DRIVER...

  • Page 7: Warning Decals

    WARNING DECALS After completing the installation of the XL-SEAT, please take the time to install the warning decals. NOTE: The surface must be clean, dry and an ambient temperature for the sticker to stick to the surface.  Start by locating a position to install the decals. ...

  • Page 8: Troubleshooting

    Burnt out switch. Replace pendant. Bad connection. Check the electronic module under the seat. Make sure that all the wires are properly connected. Burnt out electronic module. Contact Adapt Solutions for replacement module. Burnt out actuator. Replace actuator. Power Loss. The XL-SEAT motor is not getting adequate electrical power because of a loose connection.

  • Page 9: Year Limited Warranty

    The only remedy for a defect in one of Adapt Solutions products shall be the repair or the replacement, at the discretion of Adapt Solutions, of the defective part or component. If repair or replacement is not commercially practical or cannot be timely made, Adapt Solutions may decide to refund the purchase price of the equipment (XL-SEAT) instead of repairing or replacing the original equipment.