Table of Contents
Advertisement
6.1 Keyswitch Numbering
S
[0501]
[0532]
ECTIONS
TO
Keyswitch Numbering allows you to assign any hardwired input in the
system to any of the 32 keyswitch zones in the control panel (see Figure
15). UL Note: Do not use Keyswitches in UL Listed systems.
Figure 15: Example of Keyswitch Numbering
Control Panel
SN#: 020000A2
Input Terminals
1
2
3
4
5
6
7
8
Keyswitch A
Keyswitch B
Keyswitch
Zone #
Keyswitch A:
1 =
Keyswitch B:
2 =
Keyswitch C:
3 =
6.2 Keyswitch Definitions
Keyswitch Definitions determine how a keyswitch is used.
6.2.1 Keyswitch Disabled
S
[0601]
[0632]: F
ECTIONS
TO
Disables keyswitch input.
6.2.2 Momentary Keyswitch
S
[0601]
[0632]: F
ECTIONS
TO
To arm or disarm a partition using the Momentary Keyswitch, turn on the
keyswitch for three seconds then turn it off.
6.2.3 Maintained Keyswitch
S
[0601]
[0632]: F
ECTIONS
TO
To arm a partition using the Maintained Keyswitch, turn the switch from the
to the
position. Disarm it by setting the key on the
ON
OFF
6.2.4 Generates a Utility Key Event on Open
S
[0601]
[0632]: F
ECTIONS
TO
To program a keyswitch to generate a Utility Key Event:
1.
Program the Activation Event of a PGM output with the Utility Key
Event corresponding to the desired keyswitch (see PGM
Programming Table in the "EVO Programming Guide": Event Group
048).
2.
Enable option [3] in the section corresponding to the desired
keyswitch.
6.2.5 Generates a Utility Key Event on Open and Close
S
[0601]
[0632]: F
ECTIONS
TO
A Utility Key Event can be generated whenever the keyswitch input is
opened or closed. The Utility Key Events increase from 32 to 64 events;
one event for each state.
When a keyswitch is defined with the Generate a Utility Key Event on Open
and Close option, the Keyswitch Partition Assignment and Keyswitch
Options are disabled. To program a keyswitch to generate a Utility Key
Event:
1.
Program the Activation Event of a PGM output with the Utility Key
Event corresponding to the desired keyswitch (see PGM Programming
Table in the "EVO Programming Guide": Event Group 048).
Keyswitch Programming
6
C
Combus
N
OMMUNICATION
ETWORK
Zone Expansion Module
SN#: 34000041
Input Terminals
1
2
3
4
5
6
7
8
Keyswitch C
Section
Serial#
Input#
[0501]
020000A2
001
[0502]
34000041
002
[0503]
34000041
006
= 0
IRST DIGIT
= 1
IRST DIGIT
= 2
IRST DIGIT
position.
ON
= 3
IRST DIGIT
= 4
IRST DIGIT
2.
Enable option [4] in the section corresponding to the desired
keyswitch.
6.3 Keyswitch Partition Assignment
S
[0601]
[0632]: S
ECTIONS
TO
Each keyswitch must be assigned to one partition.
6.4 Keyswitch Options
Each keyswitch zone can be programmed with one or more options.
6.4.1 Disarm Only
Sections [0601] to [0632]: Option [3]
When enabled, the keyswitch can only disarm assigned partitions. The type
of disarming is determined by the other Keyswitch Options selected.
6.4.2 Stay/Instant Disarm Option (Keyswitch)
S
[0601]
[0632]: O
ECTIONS
TO
When enabled, the keyswitch can only disarm assigned Stay or Instant
armed partitions. When option [4] is disabled, the keyswitch can disarm
partitions armed using any arming method.
6.4.3 Arm Only (Keyswitch)
S
[0601]
[0632]: O
ECTIONS
TO
When enabled, the keyswitch can only arm assigned partitions. The type of
arming is determined by the other Keyswitch Options selected.
6.4.4 Regular Arming (Keyswitch)
S
[0601]
[0632]: O
ECTIONS
TO
With disabled, the arming option will be Regular arming.
6.4.5 Stay Arming (Keyswitch)
S
[0601]
[0632]: O
ECTIONS
TO
Activating the keyswitch will Stay Arm the partition.
6.4.6 Force Arming (Keyswitch)
S
[0601]
[0632]: O
ECTIONS
TO
Activating the keyswitch will force arm the selected partition.
6.4.7 Instant Arming (Keyswitch)
S
[0601]
[0632]: O
ECTIONS
TO
This option is identical to Stay arming except that all armed zones will
become Instant Zones (see section 4.4.4 on page 10).
Only one of the arming options (Stay, Force, Instant and Regular)
can be selected.
= 1
8
ECOND DIGIT
TO
[4]
PTION
[5]
PTION
[6]
[8]
PTION
TO
[6]
PTION
[7]
PTION
[8]
PTION
EVO Control Panel 15
Advertisement
Table of Contents
