Table of Contents
Advertisement
Advertisement
Chapters
Table of Contents
Related Manuals for Paradox K636
Summary of Contents for Paradox K636
-
Page 1: User Guide
32-Zone Security System Always Armed, Never Disarmed User Guide... -
Page 2: User Settings
User Settings For security reasons, write only the user’s name and not their user code. 4-Digit Codes 6-Digit Codes Stay* Force* Arm* PGM* User # and Name Byp* Duress* only only 001: Master__________________________________________________ 002: Master1_________________________________________________ 003: Master2_________________________________________________ 004:________________________________________________________ 005:________________________________________________________ 006:________________________________________________________ 007:________________________________________________________ 008:________________________________________________________ 009:________________________________________________________... -
Page 3: Zone Settings
Zone Settings Write the device type (motion detector, door contact etc.) and location. Entry Fire Fire Partition Zone Number and Description Stay Sleep Force 24Hr 1 or 2 delay zone Delay 001:______________________________ _____ 002:______________________________ _____ 003:______________________________ _____ 004:______________________________ _____ 005:______________________________ _____ 006:______________________________ _____ 007:______________________________ _____ 008:______________________________ _____... -
Page 4: Table Of Contents
Table of Contents User Codes ............. 4 Alarms ..............13 Adding / Modifying a User ..........4 Alarm Display ............13 Deleting a User ............4 Disarming & Deactivating an Alarm ......13 Panic Alarms ............13 Setting the Time & Date ........5 Fire Alarms ...............14 Setting Chime Zones .......... -
Page 5: User Codes
User Codes User codes are personal identification numbers for each user that allow you to enter certain programming modes, arm or disarm your system, as well as activate or deactivate PGMs. The system supports the following: • 1 System Master Code •... -
Page 6: Setting The Time & Date
How do I chime zones? For K636 & K10LED keypads: press & hold the zone key ([1] to [0(10)]) you wish to chime. • For K32 & K32I keypads: press & hold the [ ] key and enter the 2-digit zone number. -
Page 7: Keypads
Keypads Keypad Feedback Auditory Feedback When you enter information on the keypad, it will guide you with beep tones that communicate confirmation or rejection of your entries. You should be familiar with these two keypad beep tones: Confirmation Beep: When an operation (e.g. arming/disarming) is successfully entered on the keypad or when the system switches to a new status/mode, the keypad produces an intermittent beep tone (“... -
Page 8: Keypad Overviews
IMPORTANT: If installed on a partitioned to zones 1 to 10 respectively: OFF = System armed OFF = StayD off system, the K636 will only display partition 1. Key lit = Open or entry delay (see StayD Mode on Light (AC):... - Page 9 K10LEDV/H Keypad Overview Off Light On = StayD Enabled (see page 9) = Disarmed (page 10) Partition 1 Status Partition 2 Status = System armed (page 10) SLEEP (page 11) STAY Light (AC): On = Partition armed = Power on Off = Partition disarmed = Power off Flash= Exit Delay...
-
Page 10: Arming & Disarming With Stayd
Arming & Disarming with StayD StayD simplifies your life and makes it safer by protecting you 24 hours a day, 7 days a week without ever having to disarm the system – even when entering an armed area. StayD lives with you and protects you at all times, without any unprotected periods, and automatically re-arms the system so you don’t need to remember When entering/exiting a site, the system partly disarms to let you pass through: simply notify the system with your remote and go through the designated path which will automatically re-arm after you pass. -
Page 11: Advanced Stayd Settings
Leaving the site without changing arm mode: ] for 2 sec. Press and hold the [ ] key for 2 seconds on a keypad to leave the site without changing arm mode. Advanced StayD Settings Window Mode and Re-arm Delay In a Stay-armed system: This mode allows you to open one exterior zone without triggering an alarm. -
Page 12: Stay Arming
Stay Arming This method allows you to roam freely within the premises while the perimeter is fully armed. Stay zones are zones that are bypassed when Stay arming. For example, if you plan on staying in for the night, doors and windows can be armed without arming other zones like motion detectors. -
Page 13: One-Touch Arming
One-Touch Arming One-Touch arming allows you to arm the system without using a user code. This feature must be enabled by your installer. If One-Touch Arming is programmed, you can increase the security level of your system (from Disarm Stay Arm Sleep Arm Full Arm) without a code. -
Page 14: Alarms
How do I temporarily disable the Auto-Arm Timer? 1 Press the [ ] key. 2 Enter [ MASTER CODE 3 Press the [ ] key. The [ ] key will flash. 4 Press key [1] to set partition 1, or press key [2] to set partition 2. 5 Press and hold [ ] to temporarily disable the Auto-Arm Timer. -
Page 15: Fire Alarms
Fire Alarms Upon a fire alarm, the bell/siren will emit three “squawks” at 2 second intervals until silenced or reset by entering a valid user code. If the zone is a Delayed Fire Zone, there is a delay before the system contacts the monitoring station. -
Page 16: Communicating Using Text Messages (Pcs100)15
You can also view live status of your system and arm/disarm your system. For example, you have just left your office for the weekend but are not sure you remembered to arm it. Simply check the status of your system from a laptop and arm it remotely. - Page 17 Sending Text Messages to Arm / Disarm You can arm or disarm the system by sending a text message (SMS) from any cell phone. The message must be sent to the GSM module’s phone number, as determined by the cell phone provider (consult your installer for more information).
-
Page 18: Communicating By Phone (Voice-Guided Vdmp3)
Communicating by Phone (Voice-Guided VDMP3) You can communicate with your security system by phone by using a system accessory called the VDMP3 Voice Dialer (sold separately). The VDMP3 is a module that can be programmed to call one or more telephone numbers in the event of an alarm. -
Page 19: Vdmp3 Instructions Diagram
VDMP3 Instructions Diagram Esprit E55... -
Page 20: Advanced System Features
Partition 1, Partition 2, or both partitions. NOTE: If the system is not partitioned, all zones, user codes, and features will be recognized as belonging to Partition 1. Partitioning is not available when using a K636 keypad. Quick Function Keys Upon request of your installer or monitoring station you may have to perform one of the following. - Page 21 Panic Alarms [1] & [3] Police or_____________ Audible [4] & [6] Aux. or_______________ Audible [7] & [9] Fire or_______________ Audible PGMs PGM 1 ______________________________ PGM Utility Keys [1] & [2]: _____________________________ [2] & [3]: _____________________________ [4] & [5]: _____________________________ [5] & [6]: _____________________________ [7] &...
-
Page 22: Quick Programming
Quick Programming Master Quick Menus User Step Action Details [ ] + [ The [ ] key will flash. LED/key on = programmed user. MASTER CODE ] may also be used. PARTITION MASTER CODE 2 digits: 01 to 32. USER NUMBER Enter a 4 or 6-digit code. -
Page 23: Auto Arm
Communicator Step Action Details [ ] + [ The [ ] key will flash. MASTER CODE [3] = Personal Phone #1 [4] = Personal Phone #2 [5] = Personal Phone #3 [6] = Personal Phone #4 [7] = Personal Phone #5 [8] = Pager # #] + [ Enter phone # (up to 32 digits) and press [... -
Page 24: Index
INDEX K32LED ................8 K636 .................. 7 Access Code Length ............4 Keypad Backlight ............... 6 Adding a User ..............4 Keypad Feedback ............. 6 Advanced StayD .............. 10 Keypad Muting ..............6 Advanced System Features ..........19 Keypads ................6 Alarm Display .............. - Page 25 Stay Arming ..............11 StayD ................. 9 VDMP3 ................17 System Master Code ............4 VDMP3 Instructions ............18 System Notes ..............19 Visual Feedback ..............6 System Options ............... 22 System Timers ..............20 WARNINGS ..............25 Warranty ................24 Table of Contents ..............
- Page 26 Warranty For complete warranty information on this product please refer to the Limited Warranty Statement found on the website www.paradox.com/terms. Your use of the Paradox product signifies your acceptance of all warranty terms and conditions. Limitations of Alarm Systems We strongly advise that you review and take into consideration the “Limitations of Alarm Systems” document available on our website at http://paradox.com/Terms/.
- Page 28 We hope this product performs to your complete satisfaction. Should you have any questions or comments, please visit www.paradox.com and send us your comments. PARADOX.COM Printed in Canada - 06/2008 E55-EU01...
Need help?
Do you have a question about the K636 and is the answer not in the manual?
Questions and answers