Important Specifications; Main Specifications - Anest Iwata WIDER1L-2-12J2S Instruction Manual

INSTRUCTION MANUAL
HVLP Spray Gun
Be sure to observe warning s and cauti o ns i n this instructi o n manual.
If not, it can cause paint ejecti o n and serious bodily i n j u ry by drawi n g organic solvent.
Be sure to observe fol l owing marked items which are especially important .
Indicates a potentially hazardous situation which, if not avoided, may result in serious injury or loss of life.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury or
property damage.
Indicates notes which we ask you to observe. The safety precautions in this instruction manual are the
minimum necessary conditions. Follow national and local regulations regarding fire prevention,
electricity and safety as well as your own company regulations.
IMPORTANT WARNING: Our spray guns, airbrushes, and other products are made to conform by our local group companies with local laws and regulations
that may differ from place to place. Improper trade of products outside of designated domestic territories (unauthorized reselling) can result in legal violations,
local fines, and penalties. ANEST IWATA CORPORATION assumes no liability for products acquired through unauthorized reselling and in such cases and due
to quality control protocols, unauthorized reselling renders the warranty null and void.
Symbol Marking on the Spray Gun:
This ANEST IWATA spray gun
complies with 2014/34/EU Directive
relating to equipment and protective
systems intended for use in
explosive potentially atmospheres.

Important specifications

Max. Pressure 0.70MPa / 7.0bar / 100psi
Noise level 79dB(A)
Spray condi t i o n Recommended
Measuri n g point 1m backwards from spray gun, 1.6m height
Max. temperature Atmosphere: 5°C ~40°C (41°F~104°F)
Important
Never connect pressure feedi n g pai n t except pressure feed type spray gun.

Main specifications

Type of Nozzle orifice
Model
feed
WIDER1L-12G2P
Pressure 1.2 (0.047)
WIDER1L-2-12J2S 1.2 (0.047)
-14J2S Suction 1.4 (0.055)
-16J2S 1.6 (0.063)
WIDER1L-2-12J2G 1.2 (0.047)
-14J2G 1.4 (0.055)
Gravity
-16J2G
1.6 (0.063)
*1. Atomizing air pressure means air pressure at spray gun inlet when trigger is pulled and air flows.
*2. Tested with 16 s/Ford cup #4 automotive repair paint.
II 2 G Ex h X
II
Complies Specific Group II
with Marking for (Surface)
European Explosion
Directive Protective
Air and Fl u id: 5°C ~43°C (41°F~109°F)
Fluid nozzle
Mark
Air cap assy Mark
mm (in)
W1L WIDER1L-G2
W1L-2 WIDER1L-2-J2
2 G Ex h
Category Type of Ignition
(Zone 1&2) Atmosphere Protection
(GAS) (not applied)
WIDER1L-12G2P
WIDER1L-2-12J2S/G
WIDER1L-2-14J2S/G
WIDER1L-2-16J2S/G
Recommended condition
*1 Atomizing air Air pressure
pressure inside air cap
MPa (bar/PSI) MPa (bar/PSI)
0.34 0.07
(3.4 / 49.3) (0.7 / 10)
0.10 0.05
(1.0 / 14.5) (0.5 / 7.1)
0.13 0.07
(1.3 / 18.9) (0.7 / 10)
1
This manual contains IMPORTANT
WARNINGS and INSTRUCTIONS.
Equipment in this manual is exclusively for
painting purposes.
Do not use for other purposes.
The operator shall be fully conversant with
the requirements stated in this instruction
manual including important warnings,
cautions and operation and correct handling.
Read and understand the instruction manual,
before use and retain for reference.
IIB T6 Gb
Explosion Temperature Explosion
Group Class Protection
(Ethylene) ( 85°C) level
(EPL)
Nozzl e needle assy combinati o n
Model Fluid nozzl e
Orifice mm (i n )
1.2 (0.047)
1.2 (0.047)
1.4 (0.055)
1.6 (0.063)
Air
Fluid output consumption Pattern width
ml/min l/min (cfm) mm (in)
350 530 (18.7) 270 (10.6)
*2 60 *2 170 (6.7)
*2 80 *2 180 (7.1)
*2 95 200 (7.1) *2 190 (7.5)
*2 80 *2 200 (7.9)
*2 130 *2 220 (8.7)
100 240 (8.5) 220 (8.7)
T
Amb
X
+5°C +40°C
Additional Ambient
conditions: Temperature
Any static
El e ctricity
shoul d be
discharged
and needs to
be diverted to
the ground vi a
a conductive
air hose not
included.
Flui d needl e
Mark Mark
/ W1L / 12
08H WIDER1
/ W1L-2 / V4-12
/ W1L-2 / V4-14 13 WIDER1
/ W1L-2 / V4-16 18 WIDER1
Air & fluid
Mass
connection
g (lbs.)
Air
G1/4
(NPS1/4)
290
(0.64)
Fluid
G1/4
(NPS1/4)