Technical Specifications; Troubleshooting - Transition Networks J/POE-CF-01(SC) User Manual

J/POE-CF-01

Technical Specifications

For use with Transition Networks Model J/POE-CF-01or equivalent
Standards IEEE 802.3™, IEEE 802.3af
Data Rate 10/100 Mb/s
Packet Size (Max) 1522 bytes
Mac Address 2K
Dimensions 3.25" x 1" x 4.8" (82 mm x 25.4mm x 120mm)
Weight 0.8 lbs. (362 g) approximately
Power Consumption 20 watts (maximum)
Power Supply 48VDC, 0.67A external wall-mount adapter
Output Voltage 0.35A @ 48VDC, 16.8W
Environment Tmra*:
Storage Temp:
Humidity:
Altitude:
MTBF 49,981 MIL217F2 Hours
132,144 Bellcore Hours
Warranty Lifetime
*Manufacturer's rated ambient temperature.
Note: The information in this user's guide is subject to change. For the most
up-to-date information on the J/POE-CF-01 media converter, view the
user's guide on-line at: www.transition.com.
Product is certified by the manufacturer to comply with DHHS Rule 21/CFR,
Subchapter J applicable at the date of manufacture.
WARNING: Visible and invisible laser radiation when open. Do not stare into the beam or
view the beam directly with optical instruments. Failure to observe this warning could result
in an eye injury or blindness.
WARNING: Use of controls, adjustments or the performance of procedures other than
those specified herein may result in hazardous radiation exposure.
WARNING: If the media converter is an IEEE802.3-2005 Powered Device (PD) capable of
receiving power via the Media Dependent Interface (MDI) leads, the power source,
connector, and cabling attached to the barrel power connector must meet the isolation
requirement specified in IEEE802.3-2005. Failure to observe this warning could result in an
electrical shock.
8
24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
0 to 40°C (32 to 104°F )
-25 to 85°C (-13 to 185°F )
5 to 95%, non-condensing
0 to 10,000 feet
Technical Specifications -- continued
IMPORTANT Copper based media ports, e.g., Twisted Pair (TP) Ethernet, USB, RS232,
RS422, RS485, DS1, DS3, Video Coax, etc., are intended to be connected to intra-building
(inside plant) link segments that are not subject to lightening transients or power faults.
Copper based media ports, e.g., Twisted Pair (TP) Ethernet, USB, RS232, RS422, RS485,
DS1, DS3, Video Coax, etc., are NOT to be connected to inter-building (outside plant) link
segments that are subject to lightening transients or power faults. Failure to observe this
caution could result in damage to equipment.
MTBF is estimated using the predictability method. This method is based on MIL-
217F at 25°C ambient temperature, typical enclosure heat rise of 10°C, and
nominal operating conditions and parameters. Installation and configuration
specific MTBF estimates are available upon request. Contact Technical Support.

Troubleshooting

If the media converter fails, isolate and correct the fault by determining the
answers to the following questions and then take the indicated action:
1. Is the media converter power LED ON?
NO:
• Is the barrel connector fully inserted into the media converter?
• Is the adapter plugged into an AC outlet; if not, plug it into the outlet.
• Is the AC outlet active; if not, check the outlet's circuit beaker?
• Contact Technical Support: 1.800.466.4526, then press "2."
YES
• Proceed to step 2.
2. Is the POE LED ON?
NO
• Is there an active (connected to anther device ) RJ-45 cable inserted
into the media converter's TX port; if not, insert the cable
accordingly.
Is the power turned ON to the other device?
• Contact Technical Support: 1.800.466.4526, then press "2."
YES
• Go to step 3.
techsupport@transition.com -- Click the "Transition Now" link for a live Web chat.
9