IEI Technology ROCKY-558EV Manual

Pentium, vga & 10/100mbps ethernet sbc

Advertisement

Quick Links

ROCKY-558EV
Pentium® ,VGA & 10/100Mbps
Ethernet SBC
@Copyright 1998
All Rights Reserved.
Manual first edition May 20,1998
The information in this document is subject to change without prior notice in
order to improve reliability, design and function and does not represent a
commitment on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special,
incidental, or consequential damages arising out of the use or inability to use
the product or documentation, even if advised of the possibility of such
damages.
This document contains proprietary information protected by copyright. All
rights are reserved. No part of this manual may be reproduced by any
mechanical, electronic, or other means in any form without prior written
permission of the manufacturer.
Trademarks
ROCKY-558EV is registered trademarks of Acquire Inc.,IBM PC is a
registered trademark of International Business Machines Corporation. Intel is
a registered trademark of Intel Corporation. AMI is registered trademarks of
American Megatrends, Inc. Other product names mentioned herein are used
for identification purposes only and may be trademarks and/or registered
trademarks of their respective companies.

Advertisement

Table of Contents
loading

Summary of Contents for IEI Technology ROCKY-558EV

  • Page 1 Trademarks ROCKY-558EV is registered trademarks of Acquire Inc.,IBM PC is a registered trademark of International Business Machines Corporation. Intel is a registered trademark of Intel Corporation. AMI is registered trademarks of American Megatrends, Inc.
  • Page 3: Table Of Contents

    1. Introduction ............3 Specifications ................4 What You Have ................5 2. Installation ............6 ROCKY-558EV's Layout ............. 6 Setting the CPU of ROCKY-58EV..........8 Watch-Dog Timer ..............10 DiskOnChip™ Flash Disk ............11 BIOS Flash Type Setting............12 3.
  • Page 4 3.9 VGA Connector … … … … … … … … … … … … … … … … … … … … … … .18 3.10 Lan RJ45 Connector … … … … … … … … … … … … … … .18 3.11 CPU Fan Connector …...
  • Page 5: Introduction

    The DOC currently is available from 2MB to 72MB. An advanced high performance VGA chip – Winbond W9970CF is used in the ROCKY-558EV board. The W9970CF integrated Video Graphics Accelerator in a single chip. In addition, the ROCKY-558EV provides two 168-pin DIMM sockets for its on-board DRAM.
  • Page 6 The ROCKY-558EV Pentium® w/ VGA & 10/100MBps Ethernet Single Board Computer provides the following specification: • CPU : Pentium® MMX up to 233Mhz, AMD K6 up to 300MHz processor,Cyrix 6x86MX,IDT C6 processor • Bus : PICMG bus, meet PCI 2.1 standard •...
  • Page 7: What You Have

    +12V @ 160mA , -12V@60mA • Operating Temperature : 0° ~ 55° C ( CPU needs Cooler) 1.2 What You Have In addition to this User's Manual , the ROCKY-558EV package includes the following items: • ROCKY-558EV Pentium® w/ VGA &10/100MBps Ethernet •...
  • Page 8: Installation

    Installation This chapter describes how to install the ROCKY-558EV. At first, the layout of ROCKY-558EV is shown, and the unpacking information that you should be careful is described. The jumpers and switches setting for the ROCKY-558EV's configuration, such as CPU type selection, system clock setting, and watch dog timer, are also included.
  • Page 10: Setting The Cpu Of Rocky-58Ev

    2.2 Setting the CPU of ROCKY-558EV • CPU Clock Setting : CPU Speed/Clock 9-10 11-12 CLOSE CLOSE OPEN 55MHz 60MHz CLOSE OPEN OPEN 66MHz OPEN OPEN OPEN OPEN CLOSE CLOSE 75MHz 83MHz CLOSE OPEN CLOSE • CPU to Bus Multiple :...
  • Page 11 CPU Core Voltage CLOSE CLOSE CLOSE CLOSE 3.5V(P54C/CS) OPEN CLOSE CLOSE CLOSE 3.4V(P54C/CS) CLOSE OPEN CLOSE CLOSE 3.3V OPEN OPEN CLOSE CLOSE 3.2V 3.1V CLOSE CLOSE OPEN CLOSE OPEN CLOSE OPEN CLOSE 3.0V CLOSE OPEN OPEN CLOSE 2.9V 2.8V (P55C) OPEN OPEN OPEN...
  • Page 12: Watch-Dog Timer

    (Vcore : 2.9V ,dual voltage) PR Rating Bus MHz CPU Core Clock Multiplier 6x86MX-PR150 6x86MX-PR166 6x86MX-PR166 2.5x 6x86MX-PR200 6x86MX-PR200 2.5x 6x86MX-PR200 6x86MX-PR233 2.5x 6x86MX-PR233 6x86MX-PR233 6x86MX-PR266 3.5x 6x86MX-PR266 6x86MX-PR266 2.5x • AMD K6 MMX Rating Table(Dual Voltage) Product Name Core Freq Vcore Bus MHz Multiplier K6-233 model 6 233MHz 3.2V 3.5x...
  • Page 13: Diskonchip™ Flash Disk

    RESET WHEN WDT TIME-OUT ACTIVATE NMI TO CPU WHEN WDT TIME- DISABLE WDT OPEN • JP8: WDT Time-Out Period PERIOD OPEN OPEN CLOSE OPEN 1 sec. OPEN OPEN CLOSE CLOSE 2 sec. 10 sec. OPEN CLOSE OPEN OPEN 20 sec. OPEN CLOSE OPEN...
  • Page 14: Bios Flash Type Setting

    2.5 BIOS Flash Type Setting There have 12V or 5V programming Flash and 1MB or 2MB flash BIOS possible to be used in the board. And each type flash need specified jumper setting. • JP6: BIOS Flash Type Setting This jumper is by factory setting DESCRIPTION 12V programming 5V programming...
  • Page 15: Connection

    Connection This chapter describes how to connect peripherals, switches and indicators to the ROCKY-558EV board. 3.1 Floppy Disk Drive Connector ROCKY-558EV board equipped with a 34-pin daisy-chain driver connector cable. • J7 : FDC CONNECTOR PIN NO. DESCRIPTION PIN NO.
  • Page 16: Pci E-Ide Disk Drive Connector

    3.2 PCI E-IDE Disk Drive Connector You can attach four IDE( Integrated Device Electronics) hard disk drives to the ROCKY-558EV IDE controller. Please note the IDE support Ultra DMA/33 high performance interface. • J5 : Primary IDE Interface Connector J6 : Secondary IDE Interface Connector PIN NO.
  • Page 17: Parallel Port

    3.3 Parallel Port This port is usually connected to a printer, The ROCKY-558EV includes an on-board parallel port, accessed through a 26-pin flat-cable connector • J9 : Parallel Port Connector PIN NO. DESCRIPTION PIN NO. DESCRIPTION STROBE# DATA 0 DATA 1...
  • Page 18: Keyboard/Mouse Connector

    Pin No. Description Pin No. Description 3.5 Keyboard/Mouse Connector The ROCKY-558EV provides keyboard and mouse connectors on the bracket and board each. • J1 : 5-pin Header Keyboard Connector PIN NO. DESCRIPTION KEYBOARD CLOCK KEYBOARD DATA GROUND • J14 : 5-pin Header Mouse Connector PIN NO.
  • Page 19: Usb Port Connector

    RESET HDD LED Suspend Control 5V Standby Switch Control Signal 5V Standby 3.7 USB Port Connector The ROCKY-558EV built-in dual USB ports for the future new I/O bus expansion. • J8 : USB Connector -DATA1 +DATA0 +DATA1 -DATA0 3.8 IrDA Infrared Interface Port The ROCKY-558EV built-in a IrDA port which support Serial Infrared(SIR) or Amplitude Shift Keyed IR(ASKIR) interface.
  • Page 20: Vga Connector

    3.10 Lan RJ45 Connector The ROCKY-558EV built-in a RJ45 Lan connector.. • J12 : Lan RJ45 Connector • CN1 LED Connector(2-pin header) for Lan 10Mbps 100Mbps Active 3.11 CPU Fan Connector The ROCKY-558EV provides a connector for CPU cooling fan.
  • Page 21: Cpu Fan Connector

    • J10 CPU Fan Connector 3.12 External Battery Connector The ROCKY-558EV built-in a 3V/850mAH industrial Li-battery for CMOS and RTC backup. When normal operation will not need external battery to backup the data. • J4 : External Battery Connector PIN NO.
  • Page 22: Ami Bios Setup

    AMI BIOS Setup The ROCKY-558EV uses the AMI PCI/ISA BIOS for system configuration. The AMI BIOS setup program is designed to provide maximum flexibility in configuring the system by offering various options which may be selected for end-user requirements. This chapter is written to assist you in the proper usage of these features.
  • Page 23: Standard Cmos Setup

    4.2 Standard CMOS Setup The Standard CMOS Setup is used for basic hardware system configuration. The main function is for Date/Time setting and Floppy/Hard Disk Drive setting. Please refer the following screen for this setup. For IDE hard disk drive setup,please check the following possible setup procedure, 1.
  • Page 24: Advanced Cmos Setup

    4.3 Advanced CMOS Setup This BIOS Features Setup is designed for customer‘ s tuning best performance of the ROCKY-558EV board. As for normal operation customers don‘ t have to change any default setting. The default setting is pre-set for most reliable operation.
  • Page 25: Advanced Chipset Setup

    4.4 Advanced Chipset Setup This setup functions are almost working for ChipSet These options are used to change the ChipSet‘ s registers. Please carefully change any default setting ,otherwise the system could be running unstable.
  • Page 26: Peripheral Setup

    4.5 Peripheral Setup This setup is almost working for Multi-I/O Chip(in ALI Aladdin 4+ system chipset ). These options are used to change the ChipSet‘ s registers. Please carefully change any default setting to meet your application need perfectly. The only special concern is Onboard Serial Port2.
  • Page 27: Power Management Setup

    4.6 Power Management Setup Power Management Setup help user handles the ROCKY- 558EV board‘ s “ green” function. The features could shut down the video display and hard disk to save energy for example. The power management setup screen is as following, Power Management/APM : Disable or Enable Enable APM puts the system into power saving mode after a brief inactivity period.
  • Page 28: Pci / Plug And Play Setup

    4.7 PCI / Plug and Play Setup The PCI / Plug and Play Setup help user handles the ROCKY- 558EV board‘ s “ PCI” function. All PCI bus slots on the system use INTA#, thus all installed PCI slots must be set to this value.
  • Page 29: E 2 Key Function

    Key™ Function The ROCKY-558EV provides an outstanding E KEY™ function for system integrator. Based on the E KEY™ you could free to store the ID Code, Pass Word, or Critical Data in the 1Kbit EEPROM. Because the EEPROM is nonvolatile memory, you don’...
  • Page 30: Appendix A. Watch-Dog Timer

    EKEYDEMO.C code at first. Please note the E KEY™ function is based on the working of parallel port. So you should enable the ROCKY-558EV’ s parallel port, otherwise will be not working. Appendix A. Watch-Dog Timer The Watch-Dog Timer is provided to ensure that standalone systems can always recover from catastrophic conditions that caused the CPU to crash.
  • Page 31 external EMI or a software bug. When the CPU stops working correctly, hardware on the board will either perform a hardware reset (cold boot) or a non-maskable interrupt (NMI) to bring the system back to a known state. The Watch-Dog Timer is controlled by two I/O ports. Read Enable the refresh the Watch-Dog (hex)

Table of Contents