Working Advice; Maintenance And Service - F.F. Group CS 14/2400 PRO Original Instructions Manual

12 | English
ings, minerals and metal can be harmful to one's
health. Contact with or inhaling the dustcan trig-
ger allergic reactions to the operator or bystand-
ers and/or lead to respiratory infections. Certain
metal dust is considered hazardous, especially in
conjunction with alloys such as zinc, aluminium
or chromium. Materials containing asbestos may
only be worked by specialists.
1. Provide for good ventilation of the working
place.
2. It is recommended to wear a P2 filter-class res-
pirator.
3. Observe the relevant regulations in your coun-
try for the materials to be worked.
The blade can be blocked by dust, chips or work-
piece fragments in the slot of the base plate 13.
4. Switch the machine off and pull the mains plug
from the socket outlet.
5. Wait until the cutting disc has come to a com-
plete stop.
6. Tilt the machine toward the rear, so that small
workpiece fragments can fall out of the opening
intended for this purpose.
7. If required, use a suitable tool to remove all
workpiece fragments.
Prevent dust accumulation at the workplace. Dust
f
can easily ignite.
POSITION OF THE OPERATOR
Do not stand in a line with the cutting disc in front of
f
the machine. Always stand aside of the cutting disc.
This measure provides for better protection of your
body against possible splinters in case of cutting disc
breakage.
SWITCHING ON AND OFF
To save energy, only switch the power tool on when
using it.
To start the machine, firstly press the lock-off but-
ton 1. Then press the On/Off switch 2 and keep
it pressed.
NOTE
For safety reasons, the On/Off switch 2 cannot be
locked; it must remain pressed during the entire oper-
ation.
To switch off the machine, release the On/Off
switch 2.

WORKING ADVICE

GENERAL CUTTING INSTRUCTIONS
Do not touch the cutting disc after working before it
f
has cooled. The cutting disc becomes very hot while
working.
Make sure that the spark guard 19 is properly
mounted. Sparking occurs when cutting metal.
Protect the cutting disc against impact, shock and
grease. Do not subject the cutting disc to lateral
pressure. Do not strain the power tool so heavily
that it comes to a standstill. Excessive feed consid-
erably reduces the performance capability of the
machine and shortens the service life of the cutting
disc. Use only cutting discs that are suitable for the
material to be worked.
PERMISSIBLE WORKPIECE DIMENSIONS
Maximum workpiece sizes:
Workpiece Form
Cutting depth, max. (0°/0°): 140mm
CUTTING METAL
1. Set the desired mitre angle.
2. Firmly clamp the workpiece as appropriate for
its dimensions.
3. Switch on the machine.
Slowly guide the tool arm downward with the
handle 3.
4. Cut the workpiece applying uniform feed.
5. Switch the machine off and wait until the cut-
ting disc comes to a complete stop.
6. Guide the tool arm slowly upward.
TRANSPORT
Always carry the power tool by its transport han-
dle 17.
The power tool should always be carried by two per-
f
sons in order to avoid back injuries.
When transporting the power tool, use only the
f
transport devices and never use the protective de-
vices.

MAINTENANCE AND SERVICE

MAINTENANCE AND CLEANING
Before any work on the machine itself, pull the mains
f
plug.
Clean the ventilation slots of your power tool regu-
f
larly with a soft brush. The motor fan draws dust into
the housing, and a large accumulation of metal dust
can lead to electrical hazards.
In extreme conditions, always use dust extraction as
f
far as possible. Blow out ventilation slots frequently
and install a portable residual current device (PRCD).
When working metals, conductive dust can settle in
the interior of the power tool. The total insulation of
the power tool can be impaired.
Have maintenance and repair work performed only
f
by authorized service. In this manner, it can be en-
sured that the safety of the power tool is maintained.
The retracting blade guard must always be able to
move freely and retract automatically. Therefore,
CS 14/2400 PRO
Mitre/Bevel Angle
0° 45°
130 110
115χ115 90χ90
95χ205 85χ100
140χ140 85χ85