System 2/2 Screen - Panasonic AW-UE150KP Operating Instructions Manual

Camera menu items (continued)

System 2/2 screen

S y s t e m 2/2
T r a c k i n g D ata Output
S e r i a l
I P
I n v e r t P a n/Ti lt Axi s
C a m e r a I D
W i r e l e s s C ontr ol
F a n 1
F a n 2
R e t u r n
Tracking Data Output
Settings for the output of tracking data to be used in a virtual studio
system or elsewhere. (→ page 61)
Serial [Off, On]
Sets the function [On] or [Off] to output the tracking data, such as
Pan/Tilt/Zoom or other information from Serial Output (RS-422),
synchronized with the Genlock signal. (→ page 61)
<NOTE>
• The serial connection of the remote controller (AW-RP150, etc.)
cannot be made if [Serial] is already [On].
• In the following cases, the tracking data output may be delayed or
the value may not be updated.
- While viewing the OSD menu
- While recalling the preset value during an ongoing preset recall
- When executing AWB/ABB
- When a red or a green tally signal input has been changed
between Off and On
- When deleting a preset memory
- When an output image is flipped (turned upside down or left-right
reversed)
- After switching [Scene]
- After switching [Iris Mode]
- After switching [Super Gain]
- After switching [White Balance Mode]
- After switching each item of [Color TEMP. Setting]
- After switching [Gamma Mode]
- After switching [Matrix Type]
- After switching [Focus Mode]
- After switching [Zoom Mode]
- After switching [Max Digital Zoom]
- After switching [Digital Extender]
- After switching between [Fan1] and [Fan2]
- After switching [OSD Mix]
- After switching [Tally]
- After moving the crop frame of [UHD Crop]
- After switching [Install Position]
- After switching [Preset Speed Unit]
- When executing [Initialize] of [Maintenance]
IP [Off, On]
Sets the UDP output function [On] or [Off] to output tracking data,
such as Pan/Tilt/Zoom or other information from the IP output,
synchronized with the Genlock signal. (→ page 62)
<NOTE>
• When [IP] is [On], video transmission via IP may be delayed or the
O ff video may suffer frame loss.
O ff
We recommend setting [IP] to [Off] to avoid the delay or frame loss
O ff due to the video transmission via IP.
0x FF
• In the following cases, the tracking data output may be delayed or
Enab le
the value may not be updated.
Hi gh
- When performing video transmission via IP (M-JPEG/H.264/H.265/
Hi gh
RTMP/RTMPS/NDI|HX/SRT)
- When opening the web screen (live screen [Live] or the web
setting screen [Setup])
- While viewing the OSD menu
- While recalling the preset value during an ongoing preset recall
- When executing AWB/ABB
- When a red or a green tally signal input has been changed
between Off and On
- When deleting a preset memory
- When an output image is flipped (turned upside down or left-right
reversed)
- After switching [Scene]
- After switching [Iris Mode]
- After switching [Super Gain]
- After switching [White Balance Mode]
- After switching each item of [Color TEMP. Setting]
- After switching [Gamma Mode]
- After switching [Matrix Type]
- After switching [Focus Mode]
- After switching [Zoom Mode]
- After switching [Max Digital Zoom]
- After switching [Digital Extender]
- After switching between [Fan1] and [Fan2]
- After switching [OSD Mix]
- After switching [Tally]
- After moving the crop frame of [UHD Crop]
- After switching [Install Position]
- After switching [Preset Speed Unit]
- When executing [Initialize] of [Maintenance]
Invert Pan/Tilt Axis [Off, On]
Sets whether to invert the Pan/Tilt data for output in the tracking data.
Off
On
Camera ID [0x00 to 0xFF]
Sets the Camera ID for tracking data.
58
Pan/Tilt data is not inverted.
Pan/Tilt data is inverted for output.