Panasonic AW-UE150KP Operating Instructions Manual page 111

Web screen configurations (continued)
z SRT
„
Make SRT transmission settings.
<NOTE>
• When starting SRT transmissions in the [Listener] mode, set the
decoder and application to [Client(Caller)] mode and set the following
URL:
srt://[unit's IP address]:[value set in Client(Caller) port]
• When performing SRT transmissions in the [Client(Caller)] mode, set
the IP address and port number of the decoder and application to
[Destination IP address(IPv4)] and [Destination port], and then click
the [start] button for [SRT/MPEG2-TS/RTMP] in the live screen [Live].
Common setup
The setting is confirmed with the [Set] button.
Mode [Client(Caller), Listener]
Selects the method to connect to the SRT compatible decoder or
service.
Client(Caller) Specify the transmission destination IP address and port
number when starting transmission from this unit.
Listener Specify the listener port when awaiting the external
request to start transmission.
Factory settings: Listener
Destination IP address(IPv4)
When [Client(Caller)] is set in [Mode], enter the IP address.
Images and audio will be sent to the specified IP address.
Factory settings: 192.168.0.3
<NOTE>
• Only IPv4 can be set as the IP address.
Destination port [1024 to 50000]
When [Client(Caller)] is set in [Mode], enter the port number (used
when transmitting images from this unit).
Connection is to the specified port number.
Factory settings: 7002
Stream ID
When [Client(Caller)] is set in [Mode], enter the Stream ID.
The information entered is notified to the connection destination when
SRT transmission is started.
If the [InsertTemplate] button is clicked, the following template is
inserted in the input fields.
#!::m=publish,r=PanasonicStream
• The following characters can be displayed.
Numeric characters 0123456789
Alphabetical characters ABCDEFGHIJKLMNOPQRSTUVWXYZ
(upper and lower cases) abcdefghijklmnopqrstuvwxyz
Symbols !"#$%'()=-~^¦\`@[]{}
Factory settings: #!::m=publish,r=PanasonicStream
Streaming format
:+;<>,.?/\_
*
111
Client(Caller) port [1 to 65535]
When [Listener] is set in [Mode], enter the port number (used when
this unit is waiting for a connection).
The following port numbers are used by the unit so they cannot be
used.
20, 21, 23, 25, 42, 53, 67, 68, 69, 80, 110, 123, 161, 162, 443, 546,
547, 554, 995, 5960 to 5985, 7960 to 8060, 10669, 10670, 11900,
59000 to 61000
Factory settings: 2020
TTL/HOP Limit
The same as H.264 Multicast TTL/HOPLimit (→ page 108).
Latency
Sets the time between when images and audio are sent and when
they are played on the receiving device in a range between 0 and
99999 (ms).
Factory settings: 120
<NOTE>
• In some cases, the set time is not guaranteed depending on the
network band.
Encryption [Off, AES-128, AES-255]
Sets whether to encrypt the transmitted IP image. (10 to 24
characters)
Off Transmits unencrypted IP images.
AES-128 Encrypts IP images in AES-128 before transmitting.
AES-256 Encrypts IP images in AES-256 before transmitting.
Factory settings: Off
• The following characters can be displayed.
Numeric characters 0123456789
Alphabetical characters ABCDEFGHIJKLMNOPQRSTUVWXYZ
(upper and lower cases) abcdefghijklmnopqrstuvwxyz
Symbols _-
Passphrase
Sets the phrase used for decoding the encrypted IP images.
Makes settings for H.264 or H.265 images for use in SRT
transmission.
The setting is confirmed with the [Set] button.
Refer to the explanation for H.264 (→ page 107) or H.265
(→ page 109) for information about Image capture size, Frame rate
and Max bit rate(per client).
<NOTE>
• Streaming format settings cannot be changed during SRT
transmissions.
• When [IP(UDP)] of [Tracking Data Output] is set to [On], video
transmission via IP may be delayed or the video may suffer frame
loss. (→ page 128)
We recommend [IP(UDP)] of [Tracking Data Output] is set to [Off]
during SRT transmission.
• When the frame frequency is 24/23.98Hz, you cannot set to the
SRT(H.264), SRT(H.264 UHD), SRT(H.265), or SRT(H.265 UHD)
modes.