Collaboration Capability [Linkage] - Panasonic AW-UE150KP Operating Instructions Manual

Web screen configurations (continued)
Preset Thumbnail Update [Off, On]
Turn off/on the function for registering the still image (thumbnail) for
the images being output when a preset memory is registered.
When set to [On], the still image (thumbnail) for the images being
output is registered when registering a preset memory.
When set to [Off], the still image (thumbnail) for the images being
output is not registered when registering a preset memory, but rather
the still image (thumbnail) previously registered is maintained.
Factory settings: On
<NOTE>
• When the IP for [OSD Mix] is [On], the menu screen is included in
the thumbnails.
• When [Crop Mode] is [Crop(1080)] or [Crop(720)], the cropped still
image is registered rather than the Full image.
• When uploading Camera(ALL) or Camera(SYSTEM) on the web
screen or other access, the still image (thumbnail) that has been
registered in preset memory will be erased. (→ page 151)
Preset Name [Reset, Hold]
When registering a preset memory, set whether to reset the
previously registered preset name or keep it.
Reset When registering a preset memory, reset the
previously registered preset name.
The preset name after resetting will be [Preset
( is a 3 digit preset number: 001 to 100)
***
Hold When registering a preset memory, keep the
previously registered preset name.
Factory settings: Reset
<NOTE>
• The factory default setting for the preset name is [Preset
a 3 digit preset number: 001 to 100)
• The registration of preset names can be done in the web browser.
0 to 9, A to Z, a to z, _ , and space
Preset Iris [Off, On]
When the preset memory is played back, set whether the
reproduction of the values in the various menus related to Iris is off/
on.
When set to [On], the values set in the various menus below are
reproduced when preset memory is played back.
- Picture Level
- Iris Mode
- Auto Iris Speed
- Auto Iris Window
- Auto Iris Close Limit
Factory settings: Off
<NOTE>
• Its setting takes effect when [Mode A] or [Mode B] has been
selected as the [Preset Scope] setting.
Preset Zoom Mode [Mode A, Mode B]
Select the zoom operation for when preset memory is recalled.
Mode A Perform the zoom operation in line with the pan/tilt
operation.
Mode B Perform the zoom operation quicker than the pan/tilt
operation.
Factory settings: Mode A
Freeze During Preset [Off, On]
Turn the function for freezing images during preset playback off/on.
When this is set to [On], preset playback is performed with a still of
the image immediately preceding the start of preset playback being
output. The image freeze is released when preset playback is finished.
Factory settings: Off

Collaboration capability [Linkage]

Tracking data output settings screen [Tracking
„ „
Data Output]
Select the output mode of the tracking data and the communication
destination in the IP mode.
Up to four addresses can be specified when the IP mode is enabled.
z Setting status
„
Displays the output mode of tracking data and the destinations in IP
mode.
].
***
z Connection type
„
]. ( is
*** ***
Camera ID [0x00
Sets the Camera ID for tracking data.
Factory settings: 0xFF
Serial [On, Off]
Sets the function [On] or [Off] to output the tracking data, such as
Pan/Tilt/Zoom or other information from Serial Output (RS-422),
synchronized with the Genlock signal. (→ page 61)
When [Serial] is set to [On], a warning message is displayed. Click
the [OK] button to enable the settings.
Factory settings: Off
<NOTE>
• The serial connection of the remote controller (AW-RP150, etc.)
cannot be made if [Serial] is already [On].
• In the following cases, the tracking data output may be delayed or
the value may not be updated.
- While viewing the OSD menu
- While recalling the preset value during an ongoing preset recall
- When executing AWB/ABB
- When a red or a green tally signal input has been changed
between Off and On
- When deleting a preset memory
- When an output image is flipped (turned upside down or left-right
reversed)
- After switching [Scene]
- After switching [Iris Mode]
- After switching [Super Gain]
- After switching [White Balance Mode]
- After switching each item of [Color Temperature Setting]
- After switching [Gamma Mode]
127
0xFF]
to