Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Oliver 10062
Summary of Contents for Oliver 10062
- Page 1 Drill Press Model 10062 Owner’s Manual For Models Manufactured Since 04/2022 183999 Oliver Machinery 1-800-559-5065 921 Thomas Ave SW, Renton, WA 98057 info@olivermachinery.net Stock Number: 10062.001 WWW.OLIVERMACHINERY.NET Manual Version: 2.0.0...
- Page 3 USAGE OF SAFETY AND PROTECTION DEVICES. OLIVER MACHINERY DISCLAIMS ANY LIABILITY FOR MACHINES THAT HAVE BEEN ALTERED OR ABUSED. OLIVER MACHINERY RESERVES THE RIGHT TO EFFECT AT ANY TIME, WITHOUT PRIOR NOTICE, THOSE ALTERATIONS TO PARTS, FITTINGS, AND ACCESSORY EQUIPMENT WHICH THEY MAY DEEM NECESSARY FOR ANY REASON WHATSOEVER.
-
Page 4: Table Of Contents
Table of Contents Introduction············································· 5 Operation ·············································· 27 Preparation ·············································· 27 Specifications ·········································· 6 Drill Press Adjustments ····························· 29 Identification ··········································· 9 Table Adjustments ·········································· 29 Safety ·····················································11 Changing Drill Bits ··········································· 30 Changing Speed ··············································· 31 General Safety Guidelines ························· 11 Adjust Depth Stop ···········································... -
Page 5: Introduction
Introduction Thank you for choosing Oliver! This manual contains important information on how to safely set up, operate, and maintain this machine. Please take the time to read through this manual and make sure you understand all instructions. While this manual may provide tips on improving the result of your workpiece, the manual is not intended as a substitute for formal woodworking or metalworking training. -
Page 6: Specifications
Specifications Quick View Model 10062 Drill Press Stock Number 10062.001 Type Floor Drill Press Motor TEFC Induction Motor, 3/4 HP, 115V, 1Ph Speed Range 240 – 3400 RPM Swing 17" Drilling Capacity (Mild Steel) 3/4" Chuck JT-3 Key Chuck with 5/8" capacity Table Square Cast Iron Table, 12"... - Page 7 Max. spindle to base distance 48-1/8" Quill diameter 2-1/16" Chuck Capacity 5/8" Type JT-3 Key Chuck Speed and Drilling Capacity Spindle Speed Range 240 – 3400 RPM Total number of speeds available Drilling Capacity (Mild Steel) 3/4" 10062 Drill Press OLIVERMACHINERY.NET 7 | Page...
- Page 8 Sound Rating @ 2' distance 80 dB Center Finder Laser Class Class II Others Serial Number Location On the left side of the headstock Work Lamp Type Certification CSA 183999 Country of Origin China 8 | Page Oliver Machinery 10062 Drill Press...
-
Page 9: Identification
Identification 10062 Drill Press OLIVERMACHINERY.NET 9 | Page... - Page 10 10 | Page Oliver Machinery 10062 Drill Press...
-
Page 11: Safety
Safety Oliver Machinery has made every attempt to provide a safe, reliable, easy-to-use piece of machinery. Safety, however, is ultimately depending on the individual machine operator. Before operating this machine, please become familiar with the following safety labels and guidelines. -
Page 12: Safety Guidelines Specific To Drill Press
11. PROPER USE: Do not use this machine for anything other than its intended use. If used for other purposes, Oliver Machinery disclaims any real or implied warranty and holds itself harmless for any injury or damage which may result from that use. - Page 13 1. STOP THE MACHINE if the operator leaves the machine for any reason. 2. WAIT until the machine comes to a complete stop. 3. CLEAN UP and CLOSE POWER SWITCH COVER before departure. 10062 Drill Press OLIVERMACHINERY.NET 13 | Page...
-
Page 14: Electricals
Model Minimum Circuit Size Required 10062 Drill Press Please ensure the electrical circuit for this machine meets the minimum circuit size requirement. The minimum circuit size requirement applies to a dedicated circuit that provides power to one drill press. If more machines are sharing the same circuit, consult a licensed electrician to ensure the designated circuit is properly sized for safe operation. -
Page 15: Setup
Setup Shop Preparation Space Requirement The dimensions of 10062 Drill Press are 64-1/2”(H) x 16”(W) x 29”(D). You will need additional space for manipulating your workpiece, electrical connection, and dust collection. Load Limits This drill press weighs 198 lbs. Please ensure all lifting tools and structures have adequate load capacity for transporting and supporting the total weight of this machine, the operator, and related items. -
Page 16: Receiving
On the day of delivery, please be sure help is available to move the machine to its final location. 10062 Drill Press has a shipping weight of 198 lbs. Safe moving techniques and proper lifting equipment are required, or serious WARNING personal injury may occur. -
Page 17: Inventory
Inventory Carefully unwrap the packaging and inventory the items received: 10062 Drill Press OLIVERMACHINERY.NET 17 | Page... - Page 18 Item Purpose Safety Glasses Protection Disposable Gloves Protection Paper Towel / Rags Cleaning Rust Inhibitor Cast iron rust protection. Metric Wrench Set Assembly Metric Hex Wrench Set Assembly Retaining Ring Plier Assembly 18 | Page Oliver Machinery 10062 Drill Press...
-
Page 19: Cleaning
Never use gasoline or any highly flammable chemical as degreaser. These chemicals can cause fire and explosion. Discard oily rags in a fireproof container and keep them away from combustible WARNING materials. Oily rags can heat up and trigger spontaneous combustion under certain conditions. 10062 Drill Press OLIVERMACHINERY.NET 19 | Page... -
Page 20: Assembly
17 and gather the items by their numbers for assembly. Drill press 10062 weighs 198 lbs. and it is top-heavy. It is recommended to have at least two adults assemble and move the drill press. Serious injury and machine WARNING damage can occur when the drill press is not handled properly. - Page 21 9. With two people, lift the drill press by the headstock. A third person may be needed to keep the base on the ground from sliding. 10062 Drill Press OLIVERMACHINERY.NET 21 | Page...
- Page 22 (#4). Tighten the table lock handle to 13. Assemble the feed handle knobs (#9a) and keep the table in place. rods (#9b), then thread the feed handles into the spindle hub. 22 | Page Oliver Machinery 10062 Drill Press...
- Page 23 (#8e). Place the washer in between the screw and the screen. Do not overtighten the screws, or the screen may crack. Reinstall the retaining ring. 10062 Drill Press OLIVERMACHINERY.NET 23 | Page...
- Page 24 6. Once the arbor and chuck are joined, it is recommended to keep them attached permanently. If you need to purchase a new chuck, make sure the new chuck has a matching arbor. 24 | Page Oliver Machinery 10062 Drill Press...
-
Page 25: Test Run
The center finder laser should turn on and off accordingly. 2. If the belts are loose, go to page 31 for belt adjustment instructions. 3. Make sure both belt tension locks are tightened. 10062 Drill Press OLIVERMACHINERY.NET 25 | Page... - Page 26 Congratulations! You have completed the test run! Now your drill press is ready to use. If you discover any issues from the tests, please refer to the troubleshooting guide on page 36 to diagnose issues and make adjustments. 26 | Page Oliver Machinery 10062 Drill Press...
-
Page 27: Operation
Mark the holes for drilling. For drilling wood or soft metal, using a center punch to create a small dent at the center before drilling can prevent the drill bit from walking and missing the mark. 10062 Drill Press OLIVERMACHINERY.NET 27 | Page... - Page 28 See section "Changing Speed" on page 31 for Lock the Chuck Guard details. Before starting the drill press, cover the chuck with the chuck guard. Tighten the chuck guard lock set screw to secure the guard while drilling. 28 | Page Oliver Machinery 10062 Drill Press...
-
Page 29: Drill Press Adjustments
Table Rotation Position Adjustment 1. Loosen the table lock handle. 3. Tighten the table tilt lock bolt after adjustments. 2. Rotate the table to the desired position. 3. Tighten the table lock handle after adjustments. 10062 Drill Press OLIVERMACHINERY.NET 29 | Page... -
Page 30: Changing Drill Bits
Make use of all three holes to maximize the grip of the drill bit. 7. When finished, put away the chuck key and keep it in a safe spot. 30 | Page Oliver Machinery 10062 Drill Press... -
Page 31: Changing Speed
6. Tighten the belt tension locks to keep the belt tensioned. 7. Recheck the belt tension. The belt should deflect less than 1/2" when gently pushing the belt midway between pulleys. 8. Close the belt cover after adjustments. 10062 Drill Press OLIVERMACHINERY.NET 31 | Page... -
Page 32: Changing Chuck
Get some help to support the chuck to prevent damage. 8. Attempt to detach the chuck by hand. If the chuck is detached, make sure the joint is clean, and repeat steps 6-7. 32 | Page Oliver Machinery 10062 Drill Press... -
Page 33: Drilling
A drill press is only designed for downward cutting. Never use the drill press like a mill. Performing sideway cutting with milling bits can damage the drill press and WARNING cause the chuck to dislodge from the drill press. 10062 Drill Press OLIVERMACHINERY.NET 33 | Page... -
Page 34: Accessories
Accessories Oliver Machinery has a collection of accessories and spare parts for maintenance needs. Please visit our website OLIVERMACHINERY.NET to purchase these items. You may also call 1-800-559-5065 or email PARTS@OLIVERMACHINERY.NET to place an order. We are available Monday through Friday, 7:30 AM - 4 PM Pacific Time. -
Page 35: Maintenance
Check V-belt tension and inspect the belt for signs of wear and damage. Lubricate column, quill, and spindle. Notice: Motor and spindle bearings are permanently sealed and lubricated. They do not require lubrication. 10062 Drill Press OLIVERMACHINERY.NET 35 | Page... -
Page 36: Troubleshooting
Remount chuck. Make sure the contact surface between the arbor and the quill is free of debris. Replace damaged chuck and arbor. Loose components. Tighten the fasteners of the component. Worn bearings. Contact customer service for assistance. 36 | Page Oliver Machinery 10062 Drill Press... -
Page 37: Operation / Quality-Related Issues
Exit hole is not properly Support the workpiece with a backer board. supported. Workpiece overheated. Lower feed rate and feed pressure. Use proper lubrication when drilling metals and plastic to cool down the workpiece. 10062 Drill Press OLIVERMACHINERY.NET 37 | Page... -
Page 38: Wiring Diagram
Wiring Diagram 38 | Page Oliver Machinery 10062 Drill Press... -
Page 39: Parts List
Parts List 10062 Drill Press OLIVERMACHINERY.NET 39 | Page... - Page 40 PAN HEAD SCREW 10062-27 SWITCH BOX 10062-28 CORD CLAMP 10062-29 SCREW 10062-30 HEX NUT 10062-31 HEX NUT 10062-32 TENSION SPRING ASS'Y 10062-33 DEPTH STOP ROD 10062-34 DEPTH STOP LOCK NUT 10062-35 CORD CLAMP 40 | Page Oliver Machinery 10062 Drill Press...
- Page 41 RUBBER WASHER 10062-61 QUILL BB-6205ZZ 6205ZZ BALL BEARING 10062-63 SCREW 10062-64 DEPTH STOP BRACKET 10062-65 LOCK NUT 10062-66 SPINDLE 10062-67 ARBOR MT-2/JT-3 10062-68 5/8" CHUCK w/KEY JT-3 68-1 10062-68-1 CHUCK KEY ONLY (not shown) 10062 Drill Press OLIVERMACHINERY.NET 41 | Page...
- Page 42 BASE 10062-96 DRIFT KEY 10062-97 KEY HOLDER 10062-99 COLUMN PLATE 10062-100 RACK SEAT 10062-101 HEX HEAD BOLT M4 10062-102 HEX HEAD BOLT M10 10062-103 STOP BLOCK 10062-104 LASER TRANSFORMER 10062-105 LASER SWITCH 42 | Page Oliver Machinery 10062 Drill Press...
- Page 43 SET SCREW 10062-117 FIXED SEAT 10062-118 FIXED SEAT CONNECT BAR 10062-119 10062-120 SPRING WASHER 10062-121 CONNECT BAR 10062-122 CAP SCREW 10062-123 CHUCK GUARD 10062-124 Washer 10062-125 SPRING WASHER 10062-126 10062-127 SHAFT CLIP RING 10062 Drill Press OLIVERMACHINERY.NET 43 | Page...
-
Page 44: Maintenance Record
Maintenance Record Date Task Operator 44 | Page Oliver Machinery 10062 Drill Press... -
Page 45: Notes
Notes 10062 Drill Press OLIVERMACHINERY.NET 45 | Page... -
Page 46: Warranty And Service
Oliver Machinery makes every effort to assure that its equipment meets the highest possible standards of quality and durability. All products sold by Oliver Machinery are warranted to the original customer to be free from defects for a period of two (2) years on all parts excluding electronics and motors which are warranted for one (1) year from the date of shipment. -
Page 47: Appendix
23.018 27/64 .4219 10.715 59/64 .9219 23.415 7/16 .4375 11.112 15/16 .9375 23.812 29/64 .4531 11.509 61/64 .9531 24.209 15/32 .4687 11.906 31/32 .9687 24.606 31/64 .4844 12.303 63/64 .9844 25.003 12.700 25.400 10062 Drill Press OLIVERMACHINERY.NET 47 | Page... - Page 48 Oliver Machinery is always adding new Industrial Woodworking products to the line. For complete, up-to-date product information, visit us online at: WWW.OLIVERMACHINERY.NET or call toll free 1-800-559-5065 ** SAVE THIS MANUAL FOR FUTURE REFERENCE. **...