Page 1
Jointer Model 4265C Owner’s Manual For Models Manufactured Since 02/2021 175370 Oliver Machinery 1-800-559-5065 921 Thomas Ave SW, Renton, WA 98057 Stock Number: 4265C.101.4S info@olivermachinery.net 4265C.102.4S WWW.OLIVERMACHINERY.NET Manual Version: 2.0.0...
Page 3
USAGE OF SAFETY AND PROTECTION DEVICE. OLIVER MACHINERY DISCLAIMS ANY LIABILITY FOR MACHINES THAT HAVE BEEN ALTERED OR ABUSED. OLIVER MACHINERY RESERVES THE RIGHT TO EFFECT AT ANY TIME, WITHOUT PRIOR NOTICE, THOSE ALTERATIONS TO PARTS, FITTINGS, AND ACCESSORY EQUIPMENT WHICH THEY MAY DEEM NECESSARY FOR ANY REASON WHATSOEVER.
Introduction Thank you for choosing Oliver! This manual contains important information on how to safely set up, operate, and maintain this machine. Please take the time to read through this manual, and make sure you understand all instructions. While this manual may provide tips on optimizing the result of your workpiece, the manual is not intended as a substitute for formal woodworking training.
Page 9
Sound Rating @ 2’ distance 90-95 dB 92-96 dB Others Serial Number Location On the back of the machine. Spare Parts Included Ten cutter inserts and compatible Torx screws. Certification CSA 175370 Country of Origin Taiwan 9 | Page 4265C Jointer OLIVERMACHINERY.NET...
Safety Oliver Machinery has made every attempt to provide a safe, reliable, easy-to-use piece of machinery. Safety, however, is ultimately depending on the individual machine operator. Before operating this machine, please become familiar with the following safety labels and guidelines.
13. PROPER USE: Do not use this machine for anything other than its intended use. If used for other purposes, Oliver Machinery disclaims any real or implied warranty and holds itself harmless for any injury or damage which may result from that use.
Page 14
After Operation 1. STOP THE MACHINE if the operator leaves the machine for any reason. 2. WAIT until the machine comes to a complete stop. 3. CLEAN UP and LOCK POWER SWITCH before departure. 14 | Page Oliver Machinery 4265C Jointer...
Please ensure the electrical circuit for this machine meets the minimum circuit size requirement. The minimum circuit size requirement applies to a dedicated circuit that provides power to one 4265C Jointer. If more machines are sharing the same circuit, consult a qualified electrician to ensure the designated circuit is properly sized for safe operation.
Page 16
Using undersized wires may cause overheating and increase the risk of fire WARNING and machine damage. Improper copper-aluminum wire connection is a fire hazard. If the power circuit WARNING available uses aluminum wires, use certified CU/AL wire connectors. 16 | Page Oliver Machinery 4265C Jointer...
Piping of dust collection system introduces additional air resistance and decreases the effective CFM measured at the dust ports. Ensure there is significant suction at the dust port, so dust and debris can be effectively removed from the machine. 17 | Page 4265C Jointer OLIVERMACHINERY.NET...
On the day of delivery, please be sure help is available to move the machine to its final location. 4265C Jointer has a gross weight of 1055 lbs. and a net weight of 889 lbs. Safe moving techniques and proper lifting equipment are required, or serious WARNING personal injury may occur.
Page 19
Cutter inserts installation and for checking Torx screw tension (52-60 lb- in). T25 Star Bit Socket Cutter inserts installation. Ring Terminal Connector Connecting machine to power. IMPORTANT: Always follow local electrical code for electrical work. and Crimping Tool 19 | Page 4265C Jointer OLIVERMACHINERY.NET...
Page 20
Gently lift the machine from the pallet and move it to its final location. 4265C Jointer has a net weight of 889 lbs. All lifting devices must be capable to handle the load, or serious personal injury and machine damage may occur.
After the initial cleaning, routinely coat the unpainted cast iron surface with rust preventive such as Boeshield® T-9 or paste wax. Do not use rust preventives that contain silicone, which is known to interfere with certain finishes and glues. 21 | Page 4265C Jointer OLIVERMACHINERY.NET...
Please follow the instructions to set up the control panel: 4. Attach the last two cap screws through the table adjustment handwheel bracket. 2. Remove all six cap screws from the control panel post. 22 | Page Oliver Machinery 4265C Jointer...
Page 23
Always operate this jointer with a cutterhead guard, except for some rabbeting operations. Serious personal injury may occur when operating a jointer without a WARNING cutterhead guard. 23 | Page 4265C Jointer OLIVERMACHINERY.NET...
IMPORTANT inside the jointer. This can damage the machine and cause other hazardous situations. Check your dust collection system regularly to make sure it is not jammed or filled up. 24 | Page Oliver Machinery 4265C Jointer...
IMPORTANT: Always refer to local electrical task easier. code for properly connecting any machinery to a power source. 6. Hand tighten the sealing nut of the strain relief to keep the cord in place. 7. Re-install junction box cover. 25 | Page 4265C Jointer OLIVERMACHINERY.NET...
Turn CLOCKWISE to raise the table. • Turn ANITCLOCKWISE to lower the table. • The handle of the handwheel can be folded • down as needed. 26 | Page Oliver Machinery 4265C Jointer...
Outfeed Table Height Adjustment The outfeed table height adjustment lever is located below the outfeed table. The outfeed table height is locked by a locking cap screw. 27 | Page 4265C Jointer OLIVERMACHINERY.NET...
OR if a user recalibrates the DRO. The incremental mode shows the distance infeed table traveled since the last reset. The readings can be reset by leaving the incremental mode. 28 | Page Oliver Machinery 4265C Jointer...
Congratulations! You have completed the test run! Now your jointer is ready for production work. If you discover any issues from the tests, please refer to the troubleshooting section and maintenance section to diagnose issues and make adjustments. 29 | Page 4265C Jointer OLIVERMACHINERY.NET...
Avoid using severely warped boards, as they can be unstable and might cause severe kickbacks or disintegrate when it is cut. Glue Deposits Glue left on the workpiece surface can dull cutters and lower cut quality. Scrape off all glue deposits from the workpiece before jointing a workpiece. 30 | Page Oliver Machinery 4265C Jointer...
Keep hands at least 3” away from the cutterhead. • Use push blocks whenever possible. • Ensure the dust collection system is functional and use a dust mask. Inhaling harmful airborne particles can cause serious, long-term health issues. CAUTION 31 | Page 4265C Jointer OLIVERMACHINERY.NET...
7. As the left feeding hand approaching the cutterhead, stop feeding. Carefully lift the left-hand push block and use it to feed the portion of the workpiece that is on the outfeed table. Maintain control of the workpiece with the right hand while repositioning the left hand. 32 | Page Oliver Machinery 4265C Jointer...
Page 33
TIP: Do not feed thin stock with excessive downward pressure. This will flatten any cup or warp workpiece as it passes through the cutterhead, but it will spring back to its original shape when pressure is released. Only apply adequate pressure to maintain control of the stock when feeding. 33 | Page 4265C Jointer OLIVERMACHINERY.NET...
Be very careful when jointing narrow boards. bevel and hardness of the workpiece. Use push blocks to keep hands away from the cutterhead. Position both hands and the push blocks above the cutterhead guard when feeding. 34 | Page Oliver Machinery 4265C Jointer...
10. Reinstall cutterhead guard after rabbeting operation. If the cutterhead guard is removed for rabbeting operation, use extreme caution when performing cuts. Reinstall the guard immediately when the WARNING operation completes. 35 | Page 4265C Jointer OLIVERMACHINERY.NET...
Can happen when planing wood with high moisture content or if the cutter is dull. Sometimes it is impossible to avoid fuzzy grain due to the nature of certain wood types. To mitigate this issue, avoid using wood with high moisture content and use sharp cutters. 36 | Page Oliver Machinery 4265C Jointer...
Accessories Oliver Machinery has a collection of accessories and add-ons to enhance the productivity of your jointer. Please visit our website OLIVERMACHINERY.NET to purchase these items. You may also call 1-800-559-5065 or email PARTS@OLIVERMACHINERY.NET to place an order. We are available Monday through Friday, 9 AM - 5 PM Pacific Time.
Power Feeder Two models of power feeders are available for 4265C Jointer. They can be installed on the power feeder mount located behind the outfeed table. Features • Polyurethane covered rollers provide excellent grip while protecting the work surface. •...
Check V-belt tension and replace if the belt shows signs of cracking or glazing. Every 6 months Lubricate worm gears with grease. Notice: Motor bearings are permanently sealed and lubricated and do not require lubrication. 39 | Page 4265C Jointer OLIVERMACHINERY.NET...
5. When the height of the outfeed table is adjusted, tighten the locking cap screw to If the outfeed table height is set properly, jump lock its height. to section “Inspect Outfeed Table Parallelism”. 40 | Page Oliver Machinery 4265C Jointer...
“Adjust Table If the outfeed table is in parallel with the Parallelism/Coplanarity”. cutterhead, proceed to the next section “Inspect Infeed Table” 8. Otherwise, congratulations! The jointer tables are well calibrated for your next project! 41 | Page 4265C Jointer OLIVERMACHINERY.NET...
6. This picture shows the jointer with the parallelogram mechanism exposed. Table parallelism /coplanarity can be adjusted by rotating the eccentric nuts on the shafts [1-4]. There is a pair of eccentric nuts located on each end of these shafts. 42 | Page Oliver Machinery 4265C Jointer...
Page 43
16. Reinstall all panels and cutterhead guard when all adjustments complete. 10. Repeat the steps in “Inspect Outfeed Table Parallelism” to verify adjustments. 11. When adjustments complete, retighten the set screws to lock all outfeed table eccentric nuts. 43 | Page 4265C Jointer OLIVERMACHINERY.NET...
1. Disconnect the jointer from the power source!! 2. Loosen the jam nut that locks the stop bolt. 3. Rotate the stop bolt until it stops the infeed table at the correct height. Re-tighten the jam nuts. 44 | Page Oliver Machinery 4265C Jointer...
Do not use power tools to tighten the Torx screws. Excessive torque can strip the screws or damage the cutter inserts. 12. Reinstall the cutterhead guard and remove all tools from the table when servicing is done. 45 | Page 4265C Jointer OLIVERMACHINERY.NET...
6. With the stop bolt holding in place, tighten 7. Re-check fence stop settings. the jam nut. 8. Lock the fence before starting the jointer. 7. Re-check fence stop settings. 8. Lock the fence before starting the jointer. 46 | Page Oliver Machinery 4265C Jointer...
6. Install a new belt and make sure the belts sit into the grooves of pulleys. 7. Adjust belt tension and re-secure motor as needed. 8. Replace belt cover and motor access panel when maintenance completes. 47 | Page 4265C Jointer OLIVERMACHINERY.NET...
5. Realign motor pulley with cutterhead pulley. 6. Retighten the motor pulley locking screws, then close the belt cover and motor access panel when adjustments complete. 48 | Page Oliver Machinery 4265C Jointer...
Hit the STOP button and wait for at least 3 an operation. protection triggered. minutes. When the machine is cooled down, overload protection will reset automatically. Reduce the depth of cut and feed rate before continue. 49 | Page 4265C Jointer OLIVERMACHINERY.NET...
Outfeed table is not in Ensure the outfeed table is in parallel with the parallel with the cutterhead, and the outfeed/infeed tables are cutterhead. coplanar. More passes are Significantly twisted boards take multiple passes needed. to flatten. 50 | Page Oliver Machinery 4265C Jointer...
Page 51
Keep feed rate consistent. workpiece. Finished stock is Infeed/outfeed table Ensure the outfeed table is parallel with the concave/convex in are not coplanar. cutterhead, and the outfeed/infeed tables are the middle. coplanar. 51 | Page 4265C Jointer OLIVERMACHINERY.NET...
Page 64
380249-901 Adjusting Shaft Assembly 361303-902 Supporting Shaft 001902-105 Set Lock Screw M6*1.0P*12 190074-901 Spacer 050321-008 Motor Mounting Plate 174640-000 Stand 230403-000 Foot 000103-120 Cap Screw M6*1.0P*15 174762-156 Emergency Stop Foot Switch 280050-000 Spring 64 | Page Oliver Machinery 4265C Jointer...
Page 65
242.8 474001-013 CSA Cable SJT 18AWG*4C*1550mm 242.9 472001-050 CSA Cable SJT 18AWG*2C*2000mm Note: 440V 3Phase operation requires special components, contact Oliver Machinery. 490716-000 440V Magnetic Contactor MA-18 (5HP 3Ph) 491191-000 440V Overload RA-20 5.2 - 6.5 - 8A 000804-103 Flat Head Cap Screw M5*0.8P*10...
Page 66
Spare Parts Part Number Descriptions Specifications P-15mm 4S Insert (Sold in Box Of 10) 038201-101 Torx Screw #10-32UNF*1/2" 66 | Page Oliver Machinery 4265C Jointer...
Oliver Machinery makes every effort to assure that its equipment meets the highest possible standards of quality and durability. All products sold by Oliver Machinery are warranted to the original customer to be free from defects for a period of two (2) years on all parts excluding electronics and motors which are warranted for one (1) year from the date of shipment.
Page 71
Oliver Machinery is always adding new Industrial Woodworking products to the line. For complete, up-to-date product information, visit us online at: WWW.OLIVERMACHINERY.NET or call toll free 1-800-559-5065 ** SAVE THIS MANUAL FOR FUTURE REFERENCES. **...