Page 1
Jointer Model 4275C Owner’s Manual For Models Manufactured Since 02/2021 175370 Oliver Machinery 1-800-559-5065 921 Thomas Ave SW, Renton, WA 98057 Stock Number: 4275C.101.4S info@olivermachinery.net 4275C.102.4S WWW.OLIVERMACHINERY.NET Manual Version: 1.0.0...
Page 3
USAGE OF SAFETY AND PROTECTION DEVICES. OLIVER MACHINERY DISCLAIMS ANY LIABILITY FOR MACHINES THAT HAVE BEEN ALTERED OR ABUSED. OLIVER MACHINERY RESERVES THE RIGHT TO EFFECT AT ANY TIME, WITHOUT PRIOR NOTICE, THOSE ALTERATIONS TO PARTS, FITTINGS, AND ACCESSORY EQUIPMENT WHICH THEY MAY DEEM NECESSARY FOR ANY REASON WHATSOEVER.
Introduction Thank you for choosing Oliver! This manual contains important information on how to safely set up, operate, and maintain this machine. Please take the time to read through this manual, and make sure you understand all instructions. While this manual may provide tips on optimizing the result of your workpiece, the manual is not intended as a substitute for formal woodworking training.
Page 9
Sound Rating @ 2’ distance 90-95 dB 92-96 dB Others Serial Number Location On the back of the machine. Spare Parts Included Ten cutter inserts and compatible Torx screws. Certification CSA 175370 Country of Origin Taiwan 4275C Jointer OLIVERMACHINERY.NET 9 | Page...
Safety Oliver Machinery has made every attempt to provide a safe, reliable, easy-to-use piece of machinery. Safety, however, is ultimately depending on the individual machine operator. Before operating this machine, please become familiar with the following safety labels and guidelines.
13. PROPER USE: Do not use this machine for anything other than its intended use. If used for other purposes, Oliver Machinery disclaims any real or implied warranty and holds itself harmless for any injury or damage which may result from that use.
Page 14
After Operation 1. STOP THE MACHINE if the operator leaves the machine for any reason. 2. WAIT until the machine comes to a complete stop. 3. CLEAN UP and LOCK POWER SWITCH before departure. 14 | Page Oliver Machinery 4275C Jointer...
Please ensure the electrical circuit for this machine meets the minimum circuit size requirement. The minimum circuit size requirement applies to a dedicated circuit that provides power to one 4275C Jointer. If more machines are sharing the same circuit, consult a qualified electrician to ensure the designated circuit is properly sized for safe operation.
Page 16
Using undersized wires may cause overheating and increase the risk of fire WARNING and machine damage. Improper copper-aluminum wire connection is a fire hazard. If the power circuit available uses aluminum wires, use certified CU/AL wire connectors. WARNING 16 | Page Oliver Machinery 4275C Jointer...
Piping of the dust collection system introduces additional air resistance and CAUTION decreases the effective CFM measured at the dust ports. Ensure there is significant suction at the dust port, so dust and debris can be effectively removed from the machine. 4275C Jointer OLIVERMACHINERY.NET 17 | Page...
On the day of delivery, please be sure help is available to move the machine to its final location. 4275C Jointer has a gross weight of 1272 lbs. and a net weight of 1109 lbs. Safe moving techniques and proper lifting equipment are required, or serious WARNING personal injury may occur.
Page 19
Cutter inserts installation and for checking Torx screw tension (52-60 lb- in). T25 Star Bit Socket Cutter inserts installation. Ring Terminal Connector Connecting machine to power. and Crimping Tool IMPORTANT: Always follow local electrical code for electrical work. 4275C Jointer OLIVERMACHINERY.NET 19 | Page...
Page 20
When all items are ready for machine setup, attach the lifting sling to the lifting hooks located at the two corners of the cabinet. Gently lift the machine from the pallet and move it to its final location. 4275C Jointer has a net weight of 1109 lbs. All lifting devices must be capable to WARNING handle the load, or serious personal injury and machine damage may occur.
After the initial cleaning, routinely coat the unpainted cast iron surface with rust preventive such as Boeshield® T-9 or paste wax. Do not use rust preventives that contain silicone, which is known to interfere with certain finishes and glues. 4275C Jointer OLIVERMACHINERY.NET 21 | Page...
Please follow the instructions to set up the control panel: 4. Attach the last two cap screws through the table adjustment handwheel bracket. 2. Remove all six cap screws from the control panel post. 22 | Page Oliver Machinery 4275C Jointer...
Page 23
Always operate this jointer with a cutterhead guard, except for some rabbeting operations. Serious personal injury may occur when operating a jointer without a WARNING cutterhead guard. 4275C Jointer OLIVERMACHINERY.NET 23 | Page...
IMPORTANT inside the jointer. This can damage the machine and cause other hazardous situations. Check your dust collection system regularly to make sure it is not jammed or filled up. 24 | Page Oliver Machinery 4275C Jointer...
IMPORTANT: Always refer to local electrical task easier. code for properly connecting any machinery to a power source. 6. Hand tighten the sealing nut of the strain relief to keep the cord in place. 7. Re-install junction box cover. 4275C Jointer OLIVERMACHINERY.NET 25 | Page...
• Turn CLOCKWISE to raise the table. • Turn COUNTERCLOCKWISE to lower the table. • The handle of the handwheel can be folded down as needed. 26 | Page Oliver Machinery 4275C Jointer...
Outfeed Table Height Adjustment The outfeed table height adjustment lever is located below the outfeed table. The outfeed table height is locked by a locking cap screw. 4275C Jointer OLIVERMACHINERY.NET 27 | Page...
OR if a user recalibrates the DRO. The incremental mode shows the distance the infeed table traveled since the last reset. The readings can be reset by leaving the incremental mode. 28 | Page Oliver Machinery 4275C Jointer...
Congratulations! You have completed the test run! Now your jointer is ready for production work. If you discover any issues from the tests, please refer to the troubleshooting section and maintenance section to diagnose issues and make adjustments. 4275C Jointer OLIVERMACHINERY.NET 29 | Page...
Avoid using severely warped boards, as they can be unstable and might cause severe kickbacks or disintegrate when it is cut. Glue Deposits Glue left on the workpiece surface can dull cutters and lower cut quality. Scrape off all glue deposits from the workpiece before jointing a workpiece. 30 | Page Oliver Machinery 4275C Jointer...
Keep hands at least 3” away from the cutterhead. • Use push blocks whenever possible. Ensure the dust collection system is functional and use a dust mask. Inhaling CAUTION harmful airborne particles can cause serious, long-term health issues. 4275C Jointer OLIVERMACHINERY.NET 31 | Page...
7. As the left feeding hand approaches the cutterhead, stop feeding. Carefully lift the left-hand push block and use it to feed the portion of the workpiece that is on the outfeed table. Maintain control of the workpiece with the right hand while repositioning the left hand. 32 | Page Oliver Machinery 4275C Jointer...
Page 33
TIP: Do not feed thin stock with excessive downward pressure. This will flatten any cup or warp workpiece as it passes through the cutterhead, but it will spring back to its original shape when pressure is released. Only apply adequate pressure to maintain control of the stock when feeding. 4275C Jointer OLIVERMACHINERY.NET 33 | Page...
Be very careful when jointing narrow boards. bevel and hardness of the workpiece. Use push blocks to keep hands away from the cutterhead. Position both hands and the push blocks above the cutterhead guard when feeding. 34 | Page Oliver Machinery 4275C Jointer...
Use push blocks whenever permissible. 10. Reinstall cutterhead guard after rabbeting operation. If the cutterhead guard is removed for rabbeting operation, use extreme caution when performing cuts. Reinstall the guard immediately when the WARNING operation completes. 4275C Jointer OLIVERMACHINERY.NET 35 | Page...
Can happen when planing wood with high moisture content or if the cutter is dull. Sometimes it is impossible to avoid fuzzy grain due to the nature of certain wood types. To mitigate this issue, avoid using wood with high moisture content and use sharp cutters. 36 | Page Oliver Machinery 4275C Jointer...
Accessories Oliver Machinery has a collection of accessories and add-ons to enhance the productivity of your jointer. Please visit our website OLIVERMACHINERY.NET to purchase these items. You may also call 1-800-559-5065 or email PARTS@OLIVERMACHINERY.NET to place an order. We are available Monday through Friday, 7:30 AM - 4 PM Pacific Time.
Power Feeder Two models of power feeders are available for the 4275C Jointer. They can be installed on the power feeder mount located behind the outfeed table. Features • Polyurethane covered rollers provide excellent grip while protecting the work surface.
Check V-belt tension and replace if the belt shows signs of cracking or glazing. Every 6 months Lubricate worm gears with grease. Notice: Motor bearings are permanently sealed and lubricated and do not require lubrication. 4275C Jointer OLIVERMACHINERY.NET 39 | Page...
5. When the height of the outfeed table is adjusted, tighten the locking cap screw to If the outfeed table height is set properly, jump lock its height. to section “Inspect Outfeed Table Parallelism”. 40 | Page Oliver Machinery 4275C Jointer...
“Adjust Table If the outfeed table is in parallel with the Parallelism/Coplanarity”. cutterhead, proceed to the next section “Inspect Infeed Table” 8. Otherwise, congratulations! The jointer tables are well calibrated for your next project! 4275C Jointer OLIVERMACHINERY.NET 41 | Page...
6. This picture shows the jointer with the parallelogram mechanism exposed. Table parallelism /coplanarity can be adjusted by rotating the eccentric nuts on the shafts [1-4]. There is a pair of eccentric nuts located on each end of these shafts. 42 | Page Oliver Machinery 4275C Jointer...
Page 43
Parallelism” to verify adjustments. 11. Retighten the set screws to lock all outfeed table eccentric nuts after adjustments. 12. With the fence locked, gently rock the fence to ensure the outfeed table is stable. If the 4275C Jointer OLIVERMACHINERY.NET 43 | Page...
1. Disconnect the jointer from the power source!! 2. Loosen the jam nut that locks the stop bolt. 3. Rotate the stop bolt until it stops the infeed table at the correct height. Re-tighten the jam nuts. 44 | Page Oliver Machinery 4275C Jointer...
Do not use power tools to tighten the Torx screws. Excessive torque can strip the screws or damage the cutter inserts. 12. Reinstall the cutterhead guard and remove all tools from the table when servicing is done. 4275C Jointer OLIVERMACHINERY.NET 45 | Page...
6. With the stop bolt holding in place, tighten 7. Re-check fence stop settings. the jam nut. 8. Lock the fence before starting the jointer. 7. Re-check fence stop settings. 8. Lock the fence before starting the jointer. 46 | Page Oliver Machinery 4275C Jointer...
6. Install a new belt and make sure the belts sit into the grooves of pulleys. 7. Adjust belt tension and re-secure motor as needed. 8. Replace belt cover and motor access panel when maintenance completes. 4275C Jointer OLIVERMACHINERY.NET 47 | Page...
5mm hex wrench, and the motor pulley can move along the motor shaft. 5. Realign motor pulley with cutterhead pulley. 6. Retighten the motor pulley locking screws, then close the belt cover and motor access panel after adjustments. 48 | Page Oliver Machinery 4275C Jointer...
Hit the STOP button and wait for at least 3 an operation. protection triggered. minutes. When the machine is cooled down, overload protection will reset automatically. Reduce the depth of cut and feed rate before continue. 4275C Jointer OLIVERMACHINERY.NET 49 | Page...
Outfeed table is not in Ensure the outfeed table is in parallel with the parallel with the cutterhead, and the outfeed/infeed tables are cutterhead. coplanar. More passes are Significantly twisted boards take multiple passes needed. to flatten. 50 | Page Oliver Machinery 4275C Jointer...
Page 51
Keep feed rate consistent. workpiece. Finished stock is Infeed/outfeed table Ensure the outfeed table is parallel with the concave/convex in are not coplanar. cutterhead, and the outfeed/infeed tables are the middle. coplanar. 4275C Jointer OLIVERMACHINERY.NET 51 | Page...
Page 60
Cap w/Spring Washer/Flat M8*1.25P*20/8.2*15.4/8.5*19*2 Washer 010006-000 S Ring STW-15 320398-000 Gear 000203-101 Set Screw M6*1.0P*6 361301-902 Worm Gear 011003-114 Spring Pin 5*20 012003-001 5*5*8 361302-902 Position Shaft 330067-000 Bushing 000801-101 Flat Head Cap Screw M6*1.0P*10 60 | Page Oliver Machinery 4275C Jointer...
Page 61
Cutterhead Front Cover 000801-104 Flat Head Cap Screw M6*1.0P*20 174612-008 Digital Readout Position Plate 000103-106 Cap Screw M6*1.0P*16 000301-204 Phillips Screw M3*0.5P*15 006002-139 Flat Washer 3*8*1.0t 030127-001 Ball Bearing 606-ZZ 008315-200 Lock Nut M3*0.5P(5.5B*4H) 360906-902 Bushing 4275C Jointer OLIVERMACHINERY.NET 61 | Page...
Page 62
006308-100 Spring Washer 12.2*21.6 006001-136 Flat Washer 12.2*23*2.0t 000104-117 Cap Screw M8*1.25P*70 006001-054 Flat Washer 8.5*20*2.0t 381391-308 Bracket 000403-104 Pan Phillips Screw M6*1.0P*20 170479-000 Rear Access Panel 000101-110 Cap Screw M4*0.7*30 000102-102 Cap Screw M5*0.8P*8 62 | Page Oliver Machinery 4275C Jointer...
Oliver Machinery makes every effort to assure that its equipment meets the highest possible standards of quality and durability. All products sold by Oliver Machinery are warranted to the original customer to be free from defects for a period of two (2) years on all parts excluding electronics and motors which are warranted for one (1) year from the date of shipment.
Page 70
Oliver Machinery is always adding new Industrial Woodworking products to the line. For complete, up-to-date product information, visit us online at: WWW.OLIVERMACHINERY.NET or call toll free 1-800-559-5065 ** SAVE THIS MANUAL FOR FUTURE REFERENCES. **...