Page 1
Shaper Model 4705 Owner’s Manual For Models Manufactured Since 08/2010 175370 Oliver Machinery 1-800-559-5065 6902 S 194th St, Kent, WA 98032 Stock Number: 4705.001, 4705.002 info@olivermachinery.net Manual Version: 2.0.0 WWW.OLIVERMACHINERY.NET...
Page 3
USAGE OF SAFETY AND PROTECTION DEVICE. OLIVER MACHINERY DISCLAIMS ANY LIABILITY FOR MACHINES THAT HAVE BEEN ALTERED OR ABUSED. OLIVER MACHINERY RESERVES THE RIGHT TO EFFECT AT ANY TIME, WITHOUT PRIOR NOTICE, THOSE ALTERATIONS TO PARTS, FITTINGS, AND ACCESSORY EQUIPMENT WHICH THEY MAY DEEM NECESSARY FOR ANY REASON WHATSOEVER.
Quick View ·················································9 Dust Collection ········································· 23 Product Dimensions ····································9 Wiring and Grounding ······························ 24 Shipment Info ·············································9 Wiring Instructions for Stock Number 4705.001 Electricals ···················································9 (220V, 1 Phase) ··············································· 24 Wiring Instructions for Stock Number 4705.002 Motor ······················································ 10 (220/440V, 3 Phase) ········································...
Page 5
Elevator Assembly ···································· 54 Troubleshooting ·····································46 Motor Assembly ······································· 55 Wiring Diagram ······································48 Spindles ··················································· 56 For Stock Number 4705.001 (220V, 1Ph) ····· 48 Miter Gauge ············································· 57 For Stock Number 4705.002 (220/440V, 3Ph) ································································ 49 Maintenance Record ······························ 67 Parts List ················································50...
Introduction Thank you for choosing Oliver! This manual contains important information on how to safely set up, operate, and maintain this machine. Please take the time to read through this manual, and make sure you understand all the instructions. While this manual may provide tips on optimizing the result of your workpiece, the manual is not intended as a substitute for formal woodworking training.
Heavy cast iron base provides a steady platform. Magnetic switch with Reversible spindle gives emergency shutoff and more options for each overloading protection set-up. for safer operation. Digital readout for accurate, repeatable spindle height adjustments. 4705 Shaper OLIVERMACHINERY.NET 7 | Page...
Page 8
1/128” accuracy. Three table insert rings with alignment indicator, providing safety clearance for various cutter diameters. Table is factory pre-drilled and threaded for Oliver power feeder installation. (Power feeder sold separately) 8 | Page Oliver Machinery 4705 Shaper...
Table Insert Opening Diameter: Large 5-3/4” Medium 4-1/8” Small 2-9/16” Miter Slot Type T-Slot (Standard Size) Miter Slot Width 3/4” Miter Slot Height 3/8” Power feeder mounting locations On both rear corners of the table. 10 | Page Oliver Machinery 4705 Shaper...
4” Minimum CFM Required 800 CFM Sound Rating @ 2’ distance 85 dB Others Measurement Scale Inch Serial Number Location on the back of the machine cabinet. Certification CSA 175370 Country of Origin Taiwan 4705 Shaper OLIVERMACHINERY.NET 11 | Page...
Safety Oliver Machinery has made every attempt to provide a safe, reliable, easy-to-use piece of machinery. Safety, however, is ultimately depending on the individual machine operator. As with any piece of machinery, the operator must exercise caution, patience, and common sense at all times to safely run the machine.
12. PROPER USE: Do not use this machine for other than its intended use. If used for other purposes, Oliver disclaims any real or implied warranty and holds itself harmless for any injury or damage which may result from that use.
Page 16
Instead, pull the stock straight back away from cutter and begin the cut again. 16 | Page Oliver Machinery 4705 Shaper...
Page 17
After Operation 1. STOP THE MACHINE if the operator leaves the machine for any reason. 2. WAIT until the cutter comes to a complete stop. 3. CLEAN UP the work area before departure. 4705 Shaper OLIVERMACHINERY.NET 17 | Page...
Please ensure the electrical circuit for this machine meets the minimum circuit size requirement. Minimum circuit size requirement applies to a dedicated circuit which provides power to one 4705 Shaper. If more machines are sharing the same circuit, consult a qualified electrician to ensure the designated circuit is properly sized for safe operation.
In summary, it takes three steps to convert the shaper for 440V operation: 1. Replacing the original switch with the 440V compatible switch (Part #937600-002). 2. Follow the wiring diagram in section “Wiring Diagram - For Stock Number 4705.002 (220/440V, 3Ph)” and rewire the motor for 440v operation.
Piping of dust collection system introduces additional air resistance, and decreases CAUTION the effective CFM measured at the dust ports. Ensure both dust ports receive significant suctions from the dust collection system for removing dust and debris created by this machine. 20 | Page Oliver Machinery 4705 Shaper...
On the day of delivery, please be sure help is available to move the machine to its final location. 4705 Shaper has a gross weight of 880 lbs. and net weight of 660 lbs. Safe moving techniques and proper lifting equipment required, or serious personal WARNING injury may occur.
NOTICE: This machine comes with various standard sized, non-proprietary parts. If any of these parts are missing, we be happy to deliver them to you. To have the machine up and running as soon as possible, you can also find these parts at your local hardware store. 22 | Page Oliver Machinery 4705 Shaper...
BOTH dust ports of this machine. Minimum CFM requirement for this shaper is 800 CFM. Your dust collection system should have a rating higher than 800 CFM, as air friction from the ducts reduces the effective CFM at the dust ports. 4705 Shaper OLIVERMACHINERY.NET 23 | Page...
Make sure the voltage of your power supply matches the specifications on the motor plate of the machine. Wiring Instructions for Stock Number 4705.001 (220V, 1 Phase) 1. Power off before connecting any wires!! 2. Remove the screws that secure the cover to the connection box.
The leveling bolt has rounded equipment. Otherwise serious personal end and will sink into the center of the injury may occur. washer. 4. Adjust the depth of the bolt until the machine is completely leveled. 4705 Shaper OLIVERMACHINERY.NET 25 | Page...
Press the “On” button. Machine NOTICE: The machine will only turn on when: 1. Rotation direction switch is NOT set to “OFF”. 2. The emergency shutoff mechanism is disengaged. 3. Cabinet door is closed. 26 | Page Oliver Machinery 4705 Shaper...
3. Turn the handwheel (C) clockwise to move 7. You may flip the wheel handle down when spindle up, or counter-clockwise to move all adjustments are done. 4705 Shaper OLIVERMACHINERY.NET 27 | Page...
Page 28
Infeed/Outfeed Fence Lock Always verify cutter clearance after making adjustment to the fence. Without enough clearance, the cutter and the fence assembly will collide, and may cause WARNING serious injury and/or machine damage. 28 | Page Oliver Machinery 4705 Shaper...
Page 29
Multiply the number of that mark by 1/128”. That is the adjusted value. 3. The exact position is the sum of the coarse value and adjusted value. 4705 Shaper OLIVERMACHINERY.NET 29 | Page...
Page 30
(R) can be flipped over so that the vertical face is pointing downward. The levers (P) will have to be removed and reinstalled in order to flip the bracket and the feather board itself. 30 | Page Oliver Machinery 4705 Shaper...
3. Rotate the spindle by hand to ensure the lock is disengaged. 3. Pull and rotate the handle (A) until the pins engage into the “Lock” notch. 4. Rotate the spindle by hand until the spindle lock engages. 4705 Shaper OLIVERMACHINERY.NET 31 | Page...
Hand thread the spindle assembly into the quill. IMPORTANT: Take extra care not to cross thread, or the spindle/quill connection will be damaged. 6. Use the supplied spindle wrench to tighten the spindle nut. 32 | Page Oliver Machinery 4705 Shaper...
Page 33
9. Close the cabinet door. • Use the spindle wrench to loosen the spindle 10. Reconnect machine to power source when nut, then continue to turn until spindle all adjustments complete. assembly breaks free of the quill. 4705 Shaper OLIVERMACHINERY.NET 33 | Page...
IMPORTANT: The keyed collar MUST sit slightly ABOVE the top of the spindle. This ensures significant pressure is applied to the cutter during operation. 34 | Page Oliver Machinery 4705 Shaper...
Page 35
To Remove Cutter • Disconnect machine from power source!! • Lock the spindle arbor. • Loosen the head cap screw (F) with an 8mm hex wrench. • Remove the washer, cutter, and spacers as needed. 4705 Shaper OLIVERMACHINERY.NET 35 | Page...
1. Disconnect machine from power source!! 2. Lock the spindle arbor. 3. Raise the arbor all the way up. 6. Then tighten with the spindle wrench. 4. Loosen the collet with the spindle wrench provided. 36 | Page Oliver Machinery 4705 Shaper...
7. Check belt tension. When pushing down into the belt midway between the pulleys, the belt should flex by 1/8" using moderate finger pressure. 8. Continue with the next section to adjust belt tension as needed. 4705 Shaper OLIVERMACHINERY.NET 37 | Page...
Page 38
8. Check the movement of the belt tension lever. If it is too difficult to move, slack off on the belt tension by a bit. 38 | Page Oliver Machinery 4705 Shaper...
In this case, the outfeed fence should be adjusted to support the work piece. With the shaper running, move a small section of the workpiece through the cutter. 4705 Shaper OLIVERMACHINERY.NET 39 | Page...
Freehand shaping requires precise control of the workpiece and should only be performed by advanced users. Use the provided starting pin or a custom-made WARNING pivot board to initiate a cut. Never start freehand shaping at a corner. 40 | Page Oliver Machinery 4705 Shaper...
Accessories Oliver Machinery has a collection of accessories and add-ons to enhances productivity of your shaper. To purchase these items, please call us at 1-800-559-5065, our representatives are available Monday through Friday, 9AM - 5PM pacific time. You can also email our parts department at parts@olivermachinery.net...
Power Feeders Two power feeders are available for 4705 Shaper. They can be installed on either side of the shaper table in the back. Features • Polyurethane covered rollers provide excellent grip while protecting the work surface. • Eight feed speeds and choice of three or four rollers to fit any application.
6. Install a new belt by following step 5 in reverse. 7. Move the belt to the desired position to set the spindle speed, then check belt tension. See section “Adjusting Spindle Speed and Belt Tension” for details. 4705 Shaper OLIVERMACHINERY.NET 43 | Page...
Coplanar Adjustment 1. There are 4 nylon set screws supporting each infeed/outfeed fence. 2. Loosen the fence locking knob (H) as shown diagram. Then make small, incremental adjustment on the set screws to 44 | Page Oliver Machinery 4705 Shaper...
Page 45
5. When adjustment is complete, hold the set screw in position with the 4mm hex wrench to maintain the setting while tightening the jam nut with the 12mm wrench. 4705 Shaper OLIVERMACHINERY.NET 45 | Page...
Use provided leveling hardware as support. V-belt not tensioned Adjust belt tension. correctly Bad v-belt Replace v-belt. Spindle gib wear Adjust spindle gib pressure. Bent pulley Replace pulley. Improper motor Check and adjust motor mounting. mounting 46 | Page Oliver Machinery 4705 Shaper...
Page 47
Replace with sharp cutter. Spindle speed too low Increase RPM. Feeding too fast Pass stock more slowly. Working against grain Work with grain whenever possible. Cutting too deep On deep cuts make several passes. 4705 Shaper OLIVERMACHINERY.NET 47 | Page...
In no event shall Oliver be liable for death, personal or property injury, or damages arising from the use of its products.
Page 70
Oliver Machinery is always adding new Industrial Woodworking products to the line. For complete, up-to-date product information, visit us online at: WWW.OLIVERMACHINERY.NET or call toll free 1-800-559-5065 ** SAVE THIS MANUAL FOR FUTURE REFERENCES. **...