Toyota 7FG 10 Repair Manual page 92

3-14 3-14
eliminated. eliminated.
SST 09630-1 0110-71 SST 09630-1 0110-71
5. T 5. Tigh ighten ten bot
6. Set the dial gau 6. Set the dial gauge
and measure e the backla and measur
Standard: Sta ndard: 0. 0.2 -
If If the sta the standa
ing the diff ing the differe
means mea ns of th
Whe When n the back
Lo Loos osen en th the e ad
the rin the ring gear
sid side e equ equall
pinion. pinion.
® ®
When Wh en the backl
Lo Loos osen en th the e ad
gear ar an ge
side equally to bring the ring gear away from the drive side equally to bring the ring gear away from the drive
pinion. pinion.
7. Ti 7. Tight ghten en the adjus
fur furthe ther r by by 1.5
8. Insta 8. Install the ll the adj
9. 9. Fin Finall ally y tig tighte
T T =1 =117 17.7 -13 .7 -137. 7.3 3
[86 [86.8 .82 2 - - 10
[Point 5] [Point 5]
Disassembly: Disassembly:
1. Prev 1. Pr even ent t th the e dr driv ive e pi pini nion
woode wooden n bloc
2. Use a pla 2. Us e a plast stic ic ha
bearing. bearing.
Reassembly: Reassembly:
Assemble Assemble the
https://www.besttruckmanuals.com/
nut. nut.
both adju h adjusti sting ng nut nuts s by by one notch one notch eac
ge ver vertic ticall ally y to th to the e rin
the backlash. sh.
2 - 0. 0.3 mm 3 mm (0 (0.0 .008 - 08 - 0. 0.01
ndard rd is is not not sat satisf isfied ied, , mak make e adj
erenti ntial al cas case e ASSY ASSY in in the thr
of the adjus e adjustin ting g nut nuts. s.
the backlas lash h is is exc excess essive
adju just stin ing g nu nut on the to t on the toot oth h fl flan
g gear and and tig tighte hten n the a the adju
ally y to bri to bring ng the the rin ring gear close g gear closer r to t
the backlash ash is in is insuf suffic ficien
adju just stin ing g nu nut on the rear t on the rear si side
and tigh d tighte ten n th the e ad adju just stin ing g nu
the adjustin ting g nut on the rea nut on the rear r sid
1.5 to to 2 not 2 notche ches. s.
adjust usting ing nut nut loc lock k pla plate. te.
hten n the bear the bearing ing cap s cap set bolts
N· N·m (1 m (120 200 -14 0 -1400
101. 1.30 ft-Ibf] 30 ft-Ibf]
on fr from om da
block in k in the d the differ ifferentia ential l housi
hamm mmer er an and d re remo move
the shim, shim, rear rear bearing bearing roller,
each. h.
ring g gea gear r too tooth th fla flanks nks
012 2 in) in)
adjust ustmen ment t by mo by mov- v-
the thrust ust dir direct ection ion by by
ive: :
anks ks si side of de of
djusti sting ng nut on nut on the rear the rear
to the he dri drive ve
ient: t:
de of t of the he ri ring ng
nut t on th on the e to toot oth h fl flan ank k
side e of the ring gear of the ring gear
et bolts. .
00 kgf-cm) kgf-cm)
dama mage ge by by in inse sert rtin ing g a a
housing. ng.
ve th the e dr driv ive e pi pini nion W on W / /
roller, washer washer and and lock lock