Toyota 7FG 10 Repair Manual page 74

Reverse Reverse
1 1 st st
2nd 2nd
Forward Forward
Reverse Reverse
2nd 2nd
SST SST
https://www.besttruckmanuals.com/
Inspection: Inspection:
Measure the thr Measure the thrust ust clea clearances
gear. gear.
2nd gear: 2nd gear:
Sta Standard: ndard: 0. 0.15 - 15 - 0. 0.40 mm 40 mm (0 (0.0 .005
Re Reverse verse gea gear: r:
Sta Standard: ndard: 0. 0.10 - 10 - 0. 0.45 mm 45 mm (0 (0.0 .003
Inspection: Inspection:
Measure the radial clear Measure the radial clearance
1st gea 1st gear r . re . reve verse rse ge gea a r: r:
Standard: Sta ndard: 0. 0.01 016 6 - - 0. 0.05 057 7 mm
2n 2nd gea d gear· r· forwa forward rd ge gear ar: :
Sta Standard: ndard: 0. 0.01 018 8 - - 0. 0.06 062 2 mm (0.
[Point 2] [Point 2]
Disassembly·Reassembly: Disassembly·Reassembly:
SST 09905-00012 SST 09905-00012
Reassembly: Reassembly:
Select and install the thickest snap ring that can be installed Select and install the thickest snap ring that can be installed
to make th to make the rear bearin e rear bearing g thru
or less. or less.
Mark Mark
2.15 5 - - 2.2 2.1
A A
B B 2.25 5 - - 2.3 2.2
C C 2.3 2.35 5 - - 2.4
2.4 2.45 5 - - 2.5
0 0
2.5 2.55 5 - - 2.6
E E
[Point [Po int 3] 3]
Disassembly: Disassembly:
SST 09950-40011 SST 09950-40011
Inspection: Inspection:
Measur Mea sure e the thrus the thrust t was washer
rances of of the 2nd gear and the 2nd gear and rever
059 9 - - 0. 0.01 0157 57 in)
039 9 - - 0. 0.01 0177 77 in)
ance of of each gear. each gear.
mm (0 (0.0 .000 0063 63 - - 0. 0.00 0022
mm (0.00 0007 071 1 - - 0. 0.00 0024
thrust st clea clearance rance 0.1 mm (0.04 in) 0.1 mm (0.04 in)
Thickness Thickness
2.20 0 (0. (0.084 0846 6 - - 0.0 0.0866 866) )
2.30 0 (0. (0.088 0886 6 - - 0.0 0.0906 906) )
2.40 0 (0. (0.092 0925 5 - - 0.0 0.0945 945) )
2.50 0 (0. (0.096 0965 5 - - 0.0 0.0984 984) )
2.60 0 (0. (0.100 1004 4 - - 0.1 0.1024 024) )
her thi thickn ckness ess. .
reverse se
in)
in)
224 4 in) in)
244 4 in) in)
mm (in mm (in) )
2-19 2-19