Toyota 7FG 10 Repair Manual page 102

Point Point Operat
[Po [Point int 1] 1]
Disassembly: Disassembly:
Fix Fix the dif the differ
1. Fix the 1. Fix
SST 09410-23320-71 SST 09410-23320-71
2. U 2. Use the se the se
ASSY on ASSY
[Point [Po int 2] 2]
Disassembly: Disassembly:
Re Remo move
shim(s). shim(s).
1. Unl 1. Unlock the
2. Use th 2. Use the e inp
3. Remo 3. Remove
4. Apply a wo 4. Ap
from from damag
5. Use a 5. Use a plast
6. Rem 6. Remove
Reassembly: Reassembly:
Ins Instal tall the shim(
1. 1. Whil While e suppo
bea bearin
cla claw on the
2. Use t 2. Use the
3. Tig 3. Tighte
4. Remo 4. Remove
5. Meas 5. Measure
Standard: Standard: 8.82
If If th the e st stan
creasi cre
Good examp Good examples les
Shim thickness: Shim thickness:
0.13, 0.10, 0.15, 0.35 and
0.13, 0.10, 0.15, 0.35
(0.0051, 0.0 (0.00
6. Secu 6. S ecurel
Bad Bad examp examples les
https://www.besttruckmanuals.com/
Operations ions
ferent ential ial car carrie rier r ASS ASSY Y in a
the SST SST in t in the vise. he vise.
serv rvic ice e bo bolt lt an and d in inst stal all l th the e di diff ffer eren
on the the SST. SST.
ve th the e lo lock ck nu nut, was t, washe
ock the loc lock k nut nut. .
input ut sha shaft ft to stop the to stop the gea
ve the the loc lock k nut an nut and washe d washer. r.
ply a woode oden n blo block under the driv ck under the drive e pin
damage. e.
plastic ic hamme hammer r and remo and remove
ove the the shi shim(s m(s). ).
l the shim(s), s), rea rear bear r bearing ing rol
supporting rting the driv the drive pinion, e pinion, insta
ring, g, was washer her and lo and lock nut. Plac ck nut. Place the was
w on the dee deep p gro groove ove sid side. e.
he inp input ut sha shaft ft to sto to stop p the gear
hten n the the loc lock k nut nut to the spec to the specifi ified
ve the the inp input ut sha shaft. ft.
ure the drive the drive pinio pinion startin n starting g torqu
-13.23 3 N·m N·m (90 -135
8.82 -13.2
anda dard rd is no is not sat t satis isfi fied
asing ng or decr or decreas easing ing the shim the shim thi
and 0.40
51, 0.0039, 039, 0.005 0.0059, 0.018 9, 0.018 and
rely y swa swage ge the lock nut. the lock nut.
in a vis vise. e.
enti tial al ca
her, r, re rear bea ar beari ring ng ro roll ller er an
gear r fro from m rot rotati ation. on.
pinion to preve ion to prevent nt it it
ve the rear bea the rear bearing ring rolle
roller ler, wash , washer er and and loc lock k nut
install th ll the shim e shim(s), (s), rear
e the washer her wit with h its
the gear fro from m rot rotati ation. on.
ed tor torque que. .
torque. e.
(90 -135 kgf-cm) kgf-cm)
ed, , ma make ke ad adju just stme ment nt by in
thickn ckness ess. .
0.40 mm mm
and 0.01 0.016 6 in) in)
3-23 3-23
carr rrie ier r
and d
roller. r.
nut. .
rear
its
by in- -