Table of Contents
Advertisement
Quick Links
SERVICE & OPERATING MANUAL
Original Instructions
Certified Quality
8.19
208.13
2.38
60.45
ISO 9001 Certified
ISO 14001 Certified
10.41
264.41
1935/2004/EC
2
T
Warren Rupp, Inc.
A Unit of IDEX Corporation
800 N. Main St.,
Mansfield, Ohio 44902 USA
Telephone 419.524.8388
Fax 419.522.7867
SANDPIPERPUMP.COM
© Copyright 2017 Warren Rupp, Inc.
All rights reserved
Model F05
Metallic Food Processing Pump
5.07
128.75
Constructed with FDA Compliant Materials
Design Level 1
6.03
153.26
.25
6.35
.72
18.26
RUBBER FOOT
s a n d p i p e r p u m p. c o m
Advertisement
Table of Contents
Related Manuals for Sandpiper F05
Summary of Contents for Sandpiper F05
- Page 1 SERVICE & OPERATING MANUAL Original Instructions Certified Quality Model F05 8.19 Metallic Food Processing Pump 208.13 5.07 128.75 Constructed with FDA Compliant Materials 2.38 60.45 Design Level 1 ISO 9001 Certified ISO 14001 Certified 10.41 264.41 6.03 153.26 6.35 1935/2004/EC 18.26...
- Page 2 • Equipment is always used to transfer electrically conductive fluids or • Explosive environment is prevented from entering the internal portions of the pump, i.e. dry running For further guidance on ATEX applications, please consult the factory. sandpiperpump • Model F05 Metallic f05mdl1sm-rev0219...
-
Page 3: Table Of Contents
• Service & Repair Kits • Composite Repair Parts List • Material Codes SECTION 7: WARRANTY & CERTIFICATES ..13 • Warranty • CE Declaration of Conformity - Machinery • CE Declaration of Conformity - EC Regulation 1935/2004/EC sandpiperpump Model F05 Metallic • f05mdl1sm-rev0219... -
Page 4: Explanation Of Nomenclature
FDA Hytrel / FDA Hytrel PTFE with Neoprene Backer / PTFE PTFE One-Piece Bonded Fusion Diaphragm / PTFE Your Serial #: _____________________________________ (fill in from pump nameplate) *Complies with Code of Federal Regulations (CFR) Title 21 Part 177 sandpiperpump • Model F05 Metallic f05mdl1sm-rev0219... -
Page 5: Performance
Capacity in Liters Per Minute NOTE: Performance based on the following: PTFE fitted pump, flooded suction, water at ambient conditions. The use of other materials and varying hydraulic conditions may result in deviations in excess of 5%. sandpiperpump Model F05 Metallic • f05mdl1sm-rev0219... -
Page 6: Materials
In addition, the ambient temperature range and the process temperature range do not exceed the operating temperature range of the applied non-metallic parts as listed in the manuals of the pumps. For specific applications, always consult the Chemical Resistance Chart. Note: This document is a high level guide. Please be aware that not all model and or material combinations are possible for all sizes. Please consult factory or your distributor for specific details. sandpiperpump • Model F05 Metallic f05mdl1sm-rev0219... -
Page 7: Dimensional Drawings
189.13 6.03 153.26 6.35 24.96 18.26 18.26 RUBBER FOOT RUBBER FOOT 1-1/2” SANITARY CLAMP SUCTION PORT 8.20 208.33 4.49 113.92 4.34 3.15 110.24 80.07 1.19 30.16 RUBBER FOOT 3/8" NPT AIR EXHAUST 5.67 144.08 sandpiperpump Model F05 Metallic • f05mdl1sm-rev0219... -
Page 8: Principle Of Pump Operation
(flooded suction MUFFLER condition), pipe the exhaust higher than the product source to prevent siphoning spills. 1" DIAMETER AIR EXHAUST PIPING LIQUID LEVEL SUCTION sandpiperpump • Model F05 Metallic LINE f05mdl1sm-rev0219... -
Page 9: Recommended Installation Guide
To start the pump, slightly open the air shut-off valve. After the pump primes, the air valve can be opened to increase air flow as desired. If opening the valve increases cycling rate, but does not increase the rate of flow, cavitation has occurred. The valve should be closed slightly to obtain the most efficient air flow to pump flow ratio. sandpiperpump Model F05 Metallic • f05mdl1sm-rev0219... -
Page 10: Troubleshooting Guide
Inspect check valves and seats for wear and proper setting. Replace if necessary. Entrained air or vapor lock in chamber(s). Purge chambers through tapped chamber vent plugs. For additional troubleshooting tips contact After Sales Support at service.warrenrupp@idexcorp.com or 419-524-8388 sandpiperpump • Model F05 Metallic f05mdl1sm-rev0219... -
Page 11: Composite Repair Parts Drawing
PTFE Seat O-Rings Sleeve and Spool Set, Air Diverter, Buna Gaskets, 476.377.350 Wet End Kit Buna O-rings, Buna Shaft Seals, Pilot Retainer, FDA Hytrel Diaphragms, FDA Hytrel Check Balls, Ceramic Plate PTFE Seat O-Rings sandpiperpump Model F05 Metallic • f05mdl1sm-rev0219... - Page 12 Suction Manifold SV197FG Manifold Bolts SV197D Manifold Washer SV196C Manifold Nut SV197E Parts for Rubber Mounting Feet Item # Qty. Description Part Number Foot, Mounting 350.002.360 Nut, Hex 547.002.115 Machne Screw 706.024.115 Flat Washer 901.035.115 sandpiperpump • Model F05 Metallic f05mdl1sm-rev0219...
- Page 13 Warren Rupp brand shall fail under normal use and service due to a defect in material or workmanship within five years from the date of shipment from Warren Rupp’s factory. Warren Rupp brands include Warren Rupp ,SANDPIPER ® ® SANDPIPER Signature Series , MARATHON , Porta-Pump , SludgeMaster™ and Tranquilizer ®...
- Page 14 Declaration of Conformity Manufacturer: Warren Rupp, Inc., 800 N. Main Street, Mansfield, Ohio, 44902 USA certifies that SANDPIPER Air-Operated Double Diaphragm Food Processing Pump Models ® and Tranquilizer Surge Suppressor Models comply with the European Community Regulations: ® (EC) No 1935/2004 for Food Contact Materials...