V-Rtu2000 Series Card & Modules List - Veesta World V-RTU2000 Series Technical Information

V-RTU2000 Series
Veesta - Remote Terminal Unit
Technical Specification Manual
2.4 V-RTU2000 Series Card & Modules List
VEESTA
No.
Model
1 VR-2101A
2 VR-2101C
3 VR-2102
4 VR-2103
5 VR-2043
6 VR-2707B
7 VR-2708B
8 VR-2717A
9 VR-2715A
10 VR-2424
11 VR-2425B
12 VR-2426
13 VR-2444
14 VR-2444T
15 VR-2722A
16 VR-2723A
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization.
Table 2-1: V-RTU2000 Series Cards & Modules
Name Specification
Dimension : 3U x 42T x 185mm (H*W*D)
RTU Rack
Slot : Power x 1, CPU x 1, IO x 5, PM x 1
Dimension : 3U x 84T x 185mm (H*W*D)
RTU Rack
Slot : Power x 1, CPU x 1, IO x 5, PM x 4
Dimension : 3U x 42T x 185mm (H*W*D)
RTU Rack
Slot : Power x 1, CPU x 1, IO x 8
Dimension : 3U x 84T x 185mm (H*W*D)
RTU Rack
Slot : Power x 1, CPU x 2, IO x 16
Dimension : 3U x 84T x 185mm (H*W*D)
COM Rack
Slot : Power x 2, CPU x 2, CM x 16
Input : DC 24V or 48V
L-PS Card Output : 5V ±0.1V DC, 12W
24V ±1V DC (Internal Used), 3W
Input : 85Vrms to 260Vrms AC, or 85V to 375V DC
H-PS Card Output : 5V ±0.1V DC, 12W
24V ±1V DC (Internal Used), 3W
1 LAN Port (10/100 Base-T Ethernet) (@ Panel)
1 RS-232 Port (for Master) (@ Backplane)
CPU Card
1 RS-485 Port (for Slave Device) (@ Backplane)
1 RS-232 Port (for Test Set) (@ Panel)
1x RS-485 Port (for Master) (@ Backplane)
CPU Card 1x RS-485 Port (for Slave Device) (@ Backplane)
1x RS-232 Port (for Test Set) (@ Panel)
Half/Full Duplex 2/4 wire Lease Line
Modem Card V.23, V22bis, V.29, Bell202
1200/2400/9600 bps rate, Asynchronous/Binary
GPRS Modem Module Card
GPRS Modem Front panel Antenna connection
1x Ethernet Port + 1x RS232 Port
3G/GPRS Modem Module Card
3G/GPRS Modem Front panel Antenna connection
1x Ethernet Port + 1x RS232 Port
Half/Full Duplex 4 wire Lease Line
Modem Card FSK with programmable option
(Voice & Data) 300/600/1200 bps rate, Binary
Voice Filter with programmable option
Dispatcher Telephony System
Telephony Card Input: 4x wire, E&M telephony signaling
Output: 2x wire FXS or FXO mode selection
Input : DC 125V
DI Card
Point : 8
Input : DC 24V or DC 48V
DI Card
Point : 8
Chapter 2 - System Overview
Page 22 of 90