Antaira Technologies
IMP-C1000-SFP Series
10/100/1000TX to 100/1000FX Compact Industrial Gigabit
Media Converter with SFP Slot and PoE Injector
Quick Installation Guide
Version 1.1
Feb 2020
Tel: 1-844-268-2472
Fax: 1-714-671-9944
www.antaira.com
Package Check List
The package contains the following items:
Quick Installation Guide
1 * IMP-C1000-SFP Industrial Gigabit Media Converter
1 * Wall mounting bracket set with screws
1 * DC cable –18 AWG & DC jack 5.5x2.1mm
Front Panel Layout
Grounding Screw
4-Pin Removal Terminal Block (Power Input)
LED for PWR
LED for PoE
LED for RJ45 1000TX network speed status
10/100/1000TX RJ45 port
LED for RJ45 10/100TX network speed status
DIP switches for LFP setting
LED for network fiber connection
Fiber Port – 100/1000FX
Top Panel View
IMP-C1000-SFP series top panel is equipped with one 4-pin
removal terminal block connector for dual DC power inputs
(48~55VDC).
Product Overview
System Interface/Performance
RJ-45 port support the auto MDI/MDI-X function
Ethernet RJ-45 port connectivity 1*10/100/1000TX (w/PSE:
30W/port)
Fiber connectivity with 1*100/1000FX SFP slot
Store-and-forward switching architecture
Jumbo frame support up to 10k
Power line EFT protection: 2,000VDC; Ethernet ESD
protection: 6,000VDC
Power Input& Connection
DC 48~55VDC redundant power, with a 4-pin removal
terminal block
It is recommended to using UL listed Industrial Power
Supply
Operating Temperature
Standard operating temperature model: -10°C ~ 70°C
Extended operating temperature model (–T): -40°C ~ 80°C
Case/Installation
IP-30 protection
DIN-Rail and wall mount design
Safety Precaution
If the DC voltage is supplied by an external circuit, please use a
protection device on the power supply input.
LED Indicators
LED
Color
Description
On
Power input 1 or 2 is active
Power
Green
Off
Power input 1 and 2 are inactive
On
Linked to network at 100/1000Mbps
Link Activity
Green
Flashing
Networking is active
(SFP Port)
Off
Not connected to network
On
Linked to network at 1000Mbps
RJ45 Port
Green
Flashing
Networking is active
(Upper LED)
Off
Not connected to network
On
Linked to network at 10/100Mbps
RJ45 Port
Green
Flashing
Networking is active
(Lower LED)
Off
Not connected to network
The port is supplying power to the
On
powered-device
PoE Status
Green
No powered-device attached
Off
or power supplying fails
Quick Installation
DIP-Switching Setting
There are 2 sets of DIP‐switches on the front panel that are
responsible for the settings of the SFP (Link Fault Pass) function
and the SFP transmission rate.
DIP 1
DIP 2
ON
ON
LFP Enable and Set SFP to 100Mbps
ON
OFF
LFP Enable and Set SFP to 1000Mbps
OFF
ON
LFP Disable and Set SFP to 100Mbps
OFF
OFF
LFP Disable and Set SFP to 1000Mbps
Note: After any DIP switch changes have been made, it is
required to power cycle the unit for the changes to take
effect
Ethernet RJ45 Port (Auto MDI/MDIX)
RJ-45 port is auto-sensing for 10Base-T, 100Base-TX or
1000Base-TX devices connections. Please follow the wiring pin
assignment table below for Ethernet port installation.
RJ45 Ethernet Port Pin Outs
10/100
1000
Pins
T568A Color
T568B Color
Base-T(X)
Base-T
1
White/Green
White/Orange
Rx+
TP0+
2
Green
Orange
Rx-
TP0-
3
White/Orange
White/Green
Tx+
TP1+
4
Blue
Blue
unused
TP2+
5
White/Blue
White/Blue
unused
TP2-
6
Orange
Green
Tx-
TP1-
7
White/Brown
White/Brown
unused
TP3+
8
Brown
Brown
unused
TP3-
Description
PoE
DC+
DC+
DC-
DC-
Need help?
Do you have a question about the IMP-C1000-SFP Series and is the answer not in the manual?
Questions and answers