ANTAIRA IMP-C1000-SFP-bt-24 Series Quick Installation Manual

Antaira Technologies
IMP-C1000-SFP-bt-24 Series
Industrial Gigabit IEEE 802.3bt Ethernet-to-Fiber Media
Converter, 1*10/100/1000Tx RJ45 (90W/Port) to 1*100/1000 SFP
Slot; 12~55VDC Power Input
Quick Installation Guide
Version 1.0
(April 2020)
Tel: 1-844-268-2472
Fax: 1-714-671-9944
www.antaira.com

Package Check List

The package contains the following items:

Quick Installation Guide

IMP-C1000-SFP-bt-24(-T)

Wall Mounting bracket set with screws
 DC cable –18 AWG & DC jack 5.5x2.1mm

Front Panel Layout

4-Pin Removal Terminal Block (Power Input)
Grounding Screw
LED for Power, at PoE, and bt PoE
LED for RJ45 Link/Activity
1000Mbps
10/100/1000TX RJ45 port
LED for RJ45 Link/Activity
10/100Mbps
100/1000Fx SFP slot
LED for SFP Link/Activity
Top Panel View
IMP-C1000-SFP-bt-24 series top panel is equipped with one
4-pin removal terminal block connector for dual DC power inputs
(12~55VDC).

Product Overview

System Interface/Performance


RJ45 port support the auto MDI/MDI-X function

Ethernet RJ45 port connectivity 1*10/100/1000Tx (w/PSE:
90W/port)

Fiber connectivity with 1*100/1000Fx SFP slot

Store-and-forward switching architecture

Supports 10Kbytes Jumbo Frame
Power Input & Connection

DC 12~55VDC redundant power, with a 4-pin removal
terminal block

Max. current: 7A

Max. PoE output: 90W

It is recommended to using UL listed Industrial Power
Supply

Operating Temperature


Standard operating temperature model: -10°C ~ 65°C

Extended operating temperature model (–T): -40°C ~ 75°C
19020000000131
DIP Switch

Case/Installation


IP30 protection

DIN-Rail and wall mount design

Safety Precaution

If the DC voltage is supplied by an external circuit, please use a
protection device on the power supply input.

LED Indicators

LED Color Description
On Power input 1 or 2 is active
Power Green
Off Power input 1 and 2 are inactive
On IEEE 802.3af/at connection
AT PoE Green
Off No powered-device attached or power supplying fails
On IEEE 802.3bt connection
1. PoE over current or cable short
BT PoE Blue Flashing 2. Invalid connection check signature or connection-
check error is detected
Off No powered-device attached or power supplying fails
On Linked to network at 1000Mbps
RJ45 Port
Flashing Networking is active
(Upper LED)
Off Not connected to network
Green
On Linked to network at 10/100Mbps
RJ45 Port
Flashing Networking is active
(Lower LED)
Off Not connected to network
Green
On Connected to network, 100/1000Mbps
SFP Port
Green Flashing Networking is active
Link/Act
Off Not connected to network

DIP-Switching Setting

There are 3 sets of DIP‐switches on the front panel that are
responsible for the settings of PRRT (PD Remote Reset
Technology) function, LFP (Link Fault Pass) function, and SFP
transmission rate.
DIP-Switch Number ON
1 PRRT Enabled
2 LFP Enabled
3 SFP 100Fx
Note: After any DIP switch changes have been made, it is
required to power cycle the unit for the changes to take
effect.

Quick Installation

Ethernet RJ45 Port (Auto MDI/MDIX)
RJ-45 port is auto-sensing for 10Base-T, 100Base-TX or
1000Base-TX devices connections. Please follow the wiring pin
assignment table below for Ethernet port installation.

RJ45 Ethernet Port Pin Outs

10/100 1000
Pins T568A Color T568B Color
Base-T(X) Base-T
1 White/Green White/Orange Rx+ TP0+
2 Green Orange Rx- TP0-
3 White/Orange White/Green Tx+ TP1+
4 Blue Blue unused TP2+
5 White/Blue White/Blue unused TP2-
OFF
PRRT Disabled
LFP Disabled
SFP 1000Fx
PoE
DC+
DC+
DC-