Table of Contents
Advertisement
MAIN SUB
E7
80
Content
Communication trouble (ICU detection)
between ICU and scanner
Details
Communication establishment error/Fleming/
Parity/Protocol error
Cause
Defective connection of slave unit PWB
connector
Defective harness between slave unit PWB
and Controller PWB
Slave unit PWB mother board connector pin
breakage
Check &
Check connector and harness of slave unit
Remedy
PWB and Controller PWB.
Check grounding of machine.
90
Content
PCU communication trouble
Details
Communication establishment error/Fleming/
Parity/Protocol error
Cause
Defective connection of slave unit PWB
connector
Defective harness between slave unit PWB
and Controller PWB
Slave unit PWB mother board connector pin
breakage
Check &
Check connector and harness of slave unit
Remedy
PWB and Controller PWB.
Check grounding of machine.
F1
00
Content
Finisher (AR-FN6) communication trouble
Detail
Communication cable test error after turning
on the power or exiting from DIAG.
Communication error with the finisher
Cause
Improper connection or disconnection of
connectors and harness between the
machine and the finisher.
Finisher control PWB trouble
Control PWB (PCU) trouble
Malfunction by noises
Check and
Canceled by turning OFF/ON the power.
remedy
Check connectors and harness in the
communication line.
Replace the finisher control PWB or PCU
PWB.
08
Content
Finisher (AR-FN6) staple shift motor trouble
Detail
Staple motor drive trouble
Cause
Motor lock
Motor rpm abnormality
Overcurrent to the motor
Finisher control PWB trouble
Check and
Use DIAG (SIM3-3) to check operations of
remedy
the staple motor.
10
Content
Finisher (AR-FN6) stapler motor trouble
Detail
Stapler motor operation abnormality
Cause
Motor lock
Motor rpm abnormality
Overcurrent to the motor
Console finisher control PWB trouble
Check and
Use DIAG (SIM3-3) to check the motor
remedy
operation.
11
Content
Finisher (AR-FN6) bundle exit motor trouble
Detail
Bundle exit motor operation abnormality
Cause
Motor lock
Motor rpm abnormality
Overcurrent to the motor
Console finisher control PWB trouble
Check and
Use DIAG (SIM3-3) to check the motor
remedy
operation.
MAIN SUB
F1
15
19
20
80
87
F1
00
AR-M350 TROUBLE CODES 11-4
Content
Finisher (AR-FN6) lift motor trouble
Detail
Lift motor operation abnormality
Cause
Motor lock
Motor rpm abnormality
Overcurrent to the motor
Console finisher control PWB trouble
Content
Finisher (AR-FN6) front alignment motor
trouble
Detail
Front alignment motor operation abnormality
Cause
Motor lock
Motor rpm abnormality
Overcurrent to the motor
Console finisher control PWB trouble
Check and
Use DIAG (SIM3-3) to check the motor
remedy
operation.
Content
Finisher (AR-FN6) rear alignment motor
trouble
Detail
Rear alignment motor operation abnormality
Cause
Motor lock
Motor rpm abnormality
Overcurrent to the motor
Console finisher control PWB trouble
Check and
Use DIAG (SIM3-3) to check the motor
remedy
operation.
Content
Finisher (AR-FN6) power abnormality
Detail
The 24V power is not supplied to the finisher
PWB.
Cause
Improper connection or disconnection of
connector and harness
Finisher control PWB trouble
Power unit trouble
Check and
Use DIAG (SIM3-2) to check the sensor.
remedy
Content
Finisher (AR-FN6) staple rotation motor
trouble
Detail
Front staple rotation motor trouble
Cause
Motor lock
Motor rpm abnormality
Overcurrent to the motor
Finisher control PWB trouble
Check and
Use DIAG (SIM3-3) to check the motor
remedy
operation.
Content
Mail-bin stacker (AR-MS1)
communication trouble
Detail
Communication cable test error after turning
on the power or exiting from DIAG.
Communication error with the Mail-bin
stacker.
Cause
Improper connection or disconnection of
connector and harness between the machine
and the Mail-bin stacker.
Mail-bin stacker control PWB trouble
Control PWB (PCU) trouble
Malfunction by noises
Check and
Canceled by turning OFF/ON the power.
remedy
Check harness and connector in the
communication line.
Replace the Mail-bin stacker PWB or PCU
PWB.
Advertisement
Table of Contents
