Table of Contents
Advertisement
66-16
Purpose
Setup
Function (Content)
Used to test the dial signal (DTMF) output in the
FAX tone dial mode. (The dial number signal set
with SIM 66-13 is outputted.)
The send level can be set to an optional level.
Used to check dialing troubles and the operation.
Section
FAX
Item
Operation
Operation/Procedure The dial test is performed. (DTMF signal output)
1) The level (dB) setup is made.
(Set range: 0 - 15dB)
2) The difference between high group and low
group is set. (Set range: 0 - 15)
3) When CUSTOM SETTING is pressed,
the execution is terminated.
*
For the set value, refer to the soft SW specifications.
SIMULATION 66-16
DIAL TEST(DTMF). SELECT 0-2, AND PRESS START.
0. EXECUTE
1.HIGH
7
(dB)
2.
Select 1 or 2 and press [START] key. Press [CUSTOM SETTING] key
(When 1 is selected)
SIMULATION 66-16
DIAL TEST(DTMF). SELECT 0-15, AND PRESS START.
1.HIGH (dB)
(When 2 is selected)
SIMULATION 66-16
DIAL TEST(DTMF). SELECT 0-15, AND PRESS START.
2.
HIGH-LOW
Select 0 and
press [START] key.
(When 0 is selected)
SIMULATION 66-16
DIAL TEST(DTMF). EXECUTING...
1.HIGH
(dB)
2.
7
<List of set values>
0
Execution
1
HIGH
High group level
2
HIGH-LOW
High group - low group
66-17
Purpose
Setup
Function (Content)
Used to test the dial signal (DTMF) output in the
Fax tone dial mode. Send level 0db (fixed).
Used to check the dial IC operation.
(Only when FAX is installed.)
Section
FAX
Item
Operation
Operation/Procedure The DTMF signal output is checked.
(Output level 0)
When CUSTOM SETTING is pressed,
the execution is terminated.
SIMULATION 66-17
DTMF SIGNAL OUTPUT.(LEVEL MAX) INPUT 0 9,* ,#, AND PRESS START.
Press [START] key.
SIMULATION 66-17
DTMF SIGNAL OUTPUT.(LEVEL MAX) EXCUTING...
<DTMF signal>
1 - 9, 0, *, #
HIGH-LOW
7
or [START] key.
Press [CUSTOM SETTING] key.
HIGH-LOW
7
1
Press [CUSTOM SETTING] key.
1
AR-M350 SIMULATIONS 10-68
66-18
Purpose
Function (Content)
Section
Item
Operation/Procedure The DTMF signal output is checked.
SIMULATION 66-18
DTMF SIGNAL OUTPUT.(SOFT SW) INPUT 0 9,* ,#, AND PRESS START.
1
Press [START] key.
SIMULATION 66-18
DTMF SIGNAL OUTPUT.(SOFT SW) EXCUTING...
7
<DTMF signal>
1 - 9, 0, *, #
7
66-19
Purpose
Function (Content)
Section
Item
Operation/Procedure The content of SRAM is backed up into Flash
SIMULATION 66-19
SRAM BACK UP. (WRITE TO FLASH ROM)
ARE YOU SURE?
1. YES
2. NO
Press [START] key.
SIMULATION 66-19
SRAM BACK UP. (WRITE TO FLASH ROM) EXCUTING...
After completion of backup
<Set values>
1
Backup executed
2
No backup
Setup
Used to test the dial signal (DTMF) output in the
Fax tone dial mode.
The send level set with the soft switch is
outputted.
Used to check the dial IC operation.
(Only when FAX is installed.)
FAX
Operation
(Output level is set with soft SW.)
When CUSTOM SETTING is pressed,
the execution is terminated.
Press [CUSTOM SETTING] key.
Setup
Used to backup the FAX SRAM data
(Set values of rapid key dialing) into the flash
Memory (AR-MM9).
(When FAX is installed and FAX expansion
memory is installed.)
Fax
Operation
Memory(AR-MM9).
1
1
1
1
Advertisement
Table of Contents
