Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Kramer Cobra TS2
Summary of Contents for Kramer Cobra TS2
- Page 1 Kramer Electronics, Ltd. USER MANUAL Model: Cobra TS2 Universal Transmitter...
-
Page 2: Table Of Contents
Connections on the Single-Port VGA/RS-232 Solutions to Common Problems Technical Specifications Figures Figure 1: Connecting the Cobra TS2 with Audio Figure 2: Setting Sync Signal Output Termination Figure 3: DC Restore / AC Coupling Options Figure 4: Cobra TS2 Jumper Locations and Settings... -
Page 3: Introduction
Category 5 cable. This unit is field configurable for various video, audio and serial options (see Appendix D for configuration settings). The TS2 series feature video, audio and RS-232 signals on a single CAT 5 cable. The package includes the Cobra TS2 Universal Transmitter and this user... -
Page 4: Overview
(often associated with low quality cables) Avoiding interference from neighboring electrical appliances that may adversely influence signal quality and positioning your Cobra TS2 in a location free from moisture and away from excessive sunlight and dust Caution... -
Page 5: Setup And Installation
4th pair options will not. At the transmitter end: 1. Connect the source video to the Cobra TS2 Series transmitter video input port, which is an HD15 connector labeled VIDEO IN. 2. If desired, attach a local monitor via the local monitor port to LOOP OUT. -
Page 6: Connections On The Single-Port Vga/Rs-232
4.2 Connections on the Single-Port VGA/RS-232 The Single-Port Cobra TS2 CAT 5 Video System with RS-232 supports video and full-modem serial (RS-232) signals over CAT 5 cable. You can also use the transmitters and receivers to make video-only connections without serial communications. -
Page 7: Solutions To Common Problems
Solutions to Common Problems In most cases, nearly every issue with the Cobra TS2 CAT 5 Video System can be resolved by checking the CAT 5 termination and making sure that it’s pinned to the TIA/EIA 568B wiring specification. However, there may be other problems that cause the system to not perform as it is designed. - Page 8 For five-component (RGB/H&V) AC coupled video, the Cobra CAT 5 Video System TS2 Universal transmitter has been designed with full DC restoration capability. Solutions to Common Problems R1300S2 can only be used as an “end unit”...
-
Page 9: Table 1: Hd15 Video Connector Pinout
Appendix A Cabling Pinouts Table 1: HD15 Video Connector PINOUT Pin RGBHV (VGA) Red + Green+ Blue+ — Red- Green- Blue- — — H Sync V Sync Audio Pin 1 Left Channel Pin 2 Ground Pin 3 Right Channel Pin 4 - *S2 audio channels are reversed at the receiver end. -
Page 10: Table 3: Db9 Female Serial Connector
Appendix A Cabling Pinouts Table 3: DB9 Female Serial connector Solutions to Common Problems Full Duplex 3 wire (S2) Ground Ground Table 4: T568B CAT 5 PINOUT KRAMER: SIMPLE CREATIVE TECHNOLOGY Simplex Ground... -
Page 11: Figure 2: Setting Sync Signal Output Termination
Conversely, changing a receiver affects the output port of the receiver, not the transmitter. The following illustrations show the jumper locations for the Cobra TS2 unit. 75-ohm sync termination: To enable: Both jumpers OUT (Default) -
Page 12: Figure 3: Dc Restore / Ac Coupling Options
The following diagrams show the switch location and settings for the Cobra Universal Transmitter assembly. Note: Switch settings other than shown below may result in unpredictable performance and are not supported by Kramer. DC restore / AC coupling options: Disable:... -
Page 13: Figure 4: Cobra Ts2 Jumper Locations And Settings
The factory configuration may be changed or checked by using the following jumper location diagram as well as Table 5 for jumper settings. Figure 4: Cobra TS2 Jumper Locations and Settings... -
Page 14: Table 5: Cobra Ts2 Configuration Jumper Settings
Table 5: Cobra TS2 Configuration Jumper Settings Configuration Option (all options utilize 4th pair, except special configurations): RGBHV Computer Video With Left/Right Line Level Audio With SDPIF Digital Audio With Simplex Serial (receive only) With Composite Video With RS232 serial or S2 series (requires separate... -
Page 15: Figure 5: Receiver Mounting Bracket
19" x 1U rack. Not shown are brackets for 8 units and brackets for series receivers and transmitters. The 8-Unit Rackmount Bracket holds the mounted units like the 4-Unit Rackmount Bracket but is 2U high instead of 1U high, stacking 4 slots directly above 4 slots. - Page 16 Appendix G Setting Sync Mode The Cobra TS2 has the capability for fixed and agile sync. The default sync mode setting is for agile sync which replicates the source sync polarity signals. However some displays require a fixed sync polarity that is not possible to change at the video source.
-
Page 17: Technical Specifications
SIZE: WEIGHT: 1 Specifications are subject to change without notice Technical Specifications of the Cobra TS2 Category 5, 5e, 6 shielded or unshielded twisted pair CE; FCC Class A, IC Class/class A VGA, SVGA, XGA, XGA-2, RGBHV, RGB, Composite, S-Video, Component Video modes Up to 1920 x 1200 at up to 60 Hz (receiver dependent) Video OUT: 75 ohms;... - Page 18 KRAMER: SIMPLE CREATIVE TECHNOLOGY...
- Page 19 For the latest information on our products and a list of Kramer distributors, visit our Web site: www.kramerelectronics.com, where updates to this user manual may be found. We welcome your questions, comments and feedback. Safety Warning: Disconnect the unit from the power supply before opening/servicing.