Savant CLI-PTAC1K1 Quick Reference Manual

Relay Module for PTAC with One 6-Port Climate Relay and One 10K Thermistor Input
Quick Reference Guide
Box Contents
(1) HVAC PTAC Relay Module - (CLI-PTAC1K1)
(2) 3 Position Screw Down Plug-In Terminal Block - (028-0736)
(1) 6 Position Screw Down Plug-In Terminal Block - (028-0737)
(1) 6 Position Screw Down Plug-In Terminal Block - (028-9352)
(1) Product and Regulatory Insert (009-1706)
Supported Sensors
(available on the Savant Store)
Remote Temperature Sensor - Flush Mount (SST-TEMP1)
Outdoor Remote Temperature Sensor (SST-0TEMP1)
PLENOM Remote Sensor - Commercial (CLI-PLEN1C)
PLENOM Remote Sensor - Residential (CLI-PLEN1R)
SLAB Remote Sensor (CLI-SLAB1)
Specifications
Environmental
Temperature 32° to 104° F (0° to 40° C)
Humidity 10% to 90% Relative Humidity (non-condensing)
Dimensions and Weights
Height
3.77 inch
CLI-PTAC1K1
(9.58 cm)
6.25 inch
Shipping
(15.88 cm)
Power
Input Power 24V AC (19.2 - 28.8V AC)
Max Current Draw 0.2 amps (rms)
Maximum Wiring Distances
RS-485 Up to 1000 feet (304.8 meters) cumulative
#24 AWG - 20 feet (6.10 meters)
#20 AWG - 57 feet (17.37 meters)
Power #18 AWG - 90 feet (27.43 meters)
#16 AWG - 143 feet (43.59 meters)
#14 AWG - 228 feet (69.49 meters)
Regulatory
Safety and
Emissions
Contains FCC ID: 2AEHU-MESHTEK-H52
Contains IC: 20059-MESHTEK52
RoHS Compliant
Minimum Supported Release
Climate Config App Version 1.1.2
CLI-PTAC1K1-00 | 009-1806-00 | 190613
Copyright 2019 Savant Systems, LLC
Width Depth Weight
3.16 inch .91 inch < 1 lbs
(8.03 cm) (2.31 cm) (< .5 kg)
4.8 inch 1.25 inch < 1 lbs
(12.19 cm) (3.18 cm) (< .5 kg)
FCC Part 15
Top Panel
PTAC
A
CLI-PTACC1K1-00
S/N: SHP180601332
UID: 001AAE09CA340065
B
C
D
Blinking Green
Repeat
A
1s .5s 1s .5s
Solid Green
Climate Relays - The relay outputs on this module operate
similar to the relays of the same name on the thermostat.
Connect the relay outputs (W1, W2, Y1, etc) to the appropri-
ate connection on the PTAC equipment. Refer to the
B
Connections diagram section when making the connections.
Climate Relay LEDs - The LEDs associated with each relay
will light when the relay is energized and be off when relay is
in its idle state.
10K - Input port for a 10KΩ type temperature sensor. Any of
C
the sensors listed in the
ported on this input.
C / R Inputs - Connect 24V AC between the R and C termi-
nals. The voltage connected between these two terminals
D
will power the climate module and supply voltage to all relay
outputs See the
information.
Left Side Panel
N/C
N/C
N/C
RS-485 Port - As shown in the image above, the right three
pins connect to the RS-485 terminals on the thermostat. Re-
A
fer to the RS-485 Connections
on wiring.
1 of 2
Status
W1
W2
Y1
Y2
G
O
+
10K
C
R
RS-485 Communications is not estab-
lished. Once power is applied, it can take
up to 20 seconds to establish communi-
cations.
HELPFUL! If communications was es-
tablished and subsequently lost,
the LED will stay solid for about 1
minute before it starts blinking.
RS-485 communication is established.
Module is communicating with thermo-
stat.
Supported Sensors section are sup-
Power Connections section below for more
A
Gnd
A (TX+)
B (TX-)
section for more information
45 Perseverance Way, Hyannis, MA 02601
Savant.com
Relay
| 508.683.2500