Related Manuals for EK-Quantum Reflection Fractal ATX D5 PWM D-RGB - Plexi
Summary of Contents for EK-Quantum Reflection Fractal ATX D5 PWM D-RGB - Plexi
- Page 1 EK-Quantum Reflection Fractal ATX D5 PWM D-RGB – Plexi DISTRIBUTION PLATE USER GUIDE...
- Page 2 Before you start using this product please follow these basic guidelines: Please carefully read the manual before beginning with the installation process! The EK Fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber O-ring gaskets.
-
Page 3: Table Of Contents
TABLE OF CONTENT PREPARING THE DEFINE R6/VECTOR RS INSTALLING THE DISTRIBUTION PLATE IN THE DEFINE R6/VECTOR RS PREPARING THE DEFINE S2/MESHIFY S2 INSTALLING THE DISTRIBUTION PLATE IN THE DEFINE S2/MESHIFY S2 PREPARING THE DEFINE 7/7 XL INSTALLING THE DISTRIBUTION PLATE IN THE DEFINE 7/7 XL RECOMMENDED DISTRIBUTION PLATE CONFIGURATIONS CONFIGURATION WITH ONLY TOP RADIATOR CONFIGURATION WITH BOTH RADIATORS... -
Page 4: Preparing The Define R6/Vector Rs
PREPARING THE DEFINE R6/VECTOR RS Before installing the distribution plate, carefully read the PC case manual. STEP 1 Remove the both side panels and the front panel from the case. STEP 1 STEP 2 Remove the top filter frame and follow the process in the Fractal Design R6 case manual to remove all drive mounts and re-position the drive cover to the back of the case. - Page 5 STEP 3 Unscrew two (2) encircled screws and use the marked holes for distribution plate mounting screws. STEP 3 You can also remove the drive cover in order to secure the distribution plate with additional mounting screws if required. - 5 -...
-
Page 6: Installing The Distribution Plate In The Define R6/Vector Rs
D-RGB – Plexi distribution plate into the PC case. Make sure that mounting holes are aligned. STEP 1 STEP 2 Secure the EK-Quantum Reflection Fractal ATX D5 PWM D-RGB – Plexi distribution plate with two M3 x 10 7984DIN screws and steel washers. Steel Washer... -
Page 7: Preparing The Define S2/Meshify S2
STEP 1 Remove the both side panels from the case. STEP 1 STEP 2 Remove the hard drive cage. It can be reused, after installing EK-Quantum Reflection Fractal ATX D5 PWM D-RGB – Plexi distribution plate. STEP 2 - 7 -... -
Page 8: Installing The Distribution Plate In The Define S2/Meshify S2
D-RGB – Plexi distribution plate into the PC case. Make sure that mounting holes are aligned. STEP 1 STEP 2 Secure the EK-Quantum Reflection Fractal ATX D5 PWM D-RGB – Plexi distribution plate with enclosed M3 X 10 7984DIN mounting screws and steel washers. Steel Washer... -
Page 9: Preparing The Define 7/7 Xl
M3 X 10 mounting holes are aligned. DIN7984 Screw STEP 2 Secure the EK-Quantum Reflection Fractal ATX D5 PWM D-RGB – Plexi distribution plate with M3 x 10 7984DIN screws and steel washers. Steel Washer STEP 1&2 - 9 -... -
Page 10: Recommended Distribution Plate Configurations
RECOMMENDED DISTRIBUTION PLATE CONFIGURATIONS CONFIGURATION WITH ONLY TOP RADIATOR TOP RADIATOR All remaining and unused ports should be closed using the INLET supplied plugs and an EK-Loop Multi Allen Key (6mm, 8mm, 9mm). CPU OUTLET TOP RADIATOR CPU INLET OUTLET GPU INLET GPU OUTLET (One must be used) -
Page 11: Configuration With Both Radiators
CONFIGURATION WITH BOTH RADIATORS FRONT RADIATOR FRONT RADIATOR OUTLET INLET All remaining and unused ports should be closed using the supplied plugs and an EK-Loop Multi Allen Key (6mm, 8mm, 9mm). CPU OUTLET TOP RADIATOR INLET CPU INLET TOP RADIATOR OUTLET GPU INLET GPU OUTLET... -
Page 12: Connecting The D-Rgb Led Strip
CONNECTING THE D-RGB LED STRIP Plug the 3-pin connector of the distribution plate D-RGB LED light to the D-RGB HEADER on the motherboard. The LED will work if the pin layout on the header is as follows: +5V, Digital, Empty, Ground. Please ensure that the arrow indicated on the connector is plugged into the +5V line as indicated on your motherboard. -
Page 13: Connecting The Pump
CONNECTING THE PUMP The EK-D5 PWM pump has two connectors. 1. 4-pin Molex: It must be connected directly to your PSU at all times as it is used to power the pump. 2. 4-pin PWM fan: It can be connected to your motherboard’s CPU_ Fan or designated water pump header. -
Page 14: Support And Service
SUPPORT AND SERVICE For assistance please contact: http://support.ekwb.com/ EKWB d.o.o. Pod lipami 18 1218 Komenda Slovenia - EU SOCIAL MEDIA EKWaterBlocks @EKWaterBlocks ekwaterblocks EKWBofficial ekwaterblocks...
Need help?
Do you have a question about the Reflection Fractal ATX D5 PWM D-RGB - Plexi and is the answer not in the manual?
Questions and answers