Advertisement
Assembly procedure
1-1. Option selecting function
1-1. Option selecting function
1-1. Option selecting function
* An option setting is enabled when the starting switch is turned ON after changing the
* An option setting is enabled when the starting switch is turned ON after changing the
* An option setting is enabled when the starting switch is turned ON after changing the
setting and the starting switch is turned OFF and each controller on the machine is turned
setting and the starting switch is turned OFF and each controller on the machine is turned
setting and the starting switch is turned OFF and each controller on the machine is turned
off perfectly (about 15 seconds later).
off perfectly (about 15 seconds later).
off perfectly (about 15 seconds later).
On the "Option Select" screen, select an item with the UP (▲) and DOWN (▼) switches
On the "Option Select" screen, select an item with the UP (▲) and DOWN (▼) switches
On the "Option Select" screen, select an item with the UP (▲) and DOWN (▼) switches
and determine it with the ENTER switch, and set each item in order.
and determine it with the ENTER switch, and set each item in order.
and determine it with the ENTER switch, and set each item in order.
★ Optional components installation setting table
★ Optional components installation setting table
★ Optional components installation setting table
Item name
Item name
Item name
Work Equipment Control
Work Equipment Control
Work Equipment Control
Multicoupler
Multicoupler
Multicoupler
Semi-auto Digging
Semi-auto Digging
Semi-auto Digging
Load Meter
Load Meter
Load Meter
Boom specification
Boom specification
Boom specification
Auto Grease
Auto Grease
Auto Grease
Battery Electrolyte Level
Battery Electrolyte Level
Battery Electrolyte Level
Sensor
Sensor
Sensor
Ti
Tire Size Compensation
Tire Size Compensation
Si
C
Tire Type
Tire Type
Emergency Steering
Emergency Steering
J/S or FNR SWITCH
J/S or FNR SWITCH
Lift Up Mode
Lift Up Mode
E.C.S.S.
E.C.S.S.
Torque Converter Lockup
Torque Converter Lockup
4th Gear Prohibition
4th Gear Prohibition
Two Stage Low Idle
Two Stage Low Idle
F1 PWR CUT
F1 PWR CUT
Komatsu SmartLoader
Komatsu SmartLoader
Logic
Logic
Precautions
NO.0030
Default
Default
Default
Remarks
Remarks
Remarks
TYPE A
TYPE A
TYPE A
See "1-2. Change or setting of "Work Equipment Control""
See "1-2. Change or setting of "Work Equipment Control""
See "1-2. Change or setting of "Work Equipment Control""
NO ADD
NO ADD
NO ADD
Perform following setting according to installation state of
Perform following setting according to installation state of
Perform following setting according to installation state of
option and destination
option and destination
option and destination
･ If option is installed and destination is inside Japan, set
･ If option is installed and destination is inside Japan, set
･ If option is installed and destination is inside Japan, set
"JAPAN SPEC"
"JAPAN SPEC"
"JAPAN SPEC"
･ If option is installed and destination is outside Japan, set
･ If option is installed and destination is outside Japan, set
･ If option is installed and destination is outside Japan, set
"OTHERS"
"OTHERS"
"OTHERS"
･ If option is not installed, set "NO ADD"
･ If option is not installed, set "NO ADD"
･ If option is not installed, set "NO ADD"
ADD
ADD
ADD
Set "ADD" and do not change
Set "ADD" and do not change
Set "ADD" and do not change
NO ADD
NO ADD
NO ADD
If option is installed, select "ADD" (only JPN specification)
If option is installed, select "ADD" (only JPN specification)
If option is installed, select "ADD" (only JPN specification)
Standard
Standard
Standard
Perform following setting according to boom specification
Perform following setting according to boom specification
Perform following setting according to boom specification
･ If STD boom is installed, select "Standard"
･ If STD boom is installed, select "Standard"
･ If STD boom is installed, select "Standard"
･ If high-lift boom (optional) is installed, select "High Lift"
･ If high-lift boom (optional) is installed, select "High Lift"
･ If high-lift boom (optional) is installed, select "High Lift"
NO ADD
NO ADD
NO ADD
If option is installed, select "ADD" (only EU specification)
If option is installed, select "ADD" (only EU specification)
If option is installed, select "ADD" (only EU specification)
NO ADD
NO ADD
NO ADD
Set "NO ADD" and do not change
Set "NO ADD" and do not change
Set "NO ADD" and do not change
ti
0%
0%
0%
If di l
If displayed travel speed is not correct, adjust it with this
If displayed travel speed is not correct, adjust it with this
function
function
If setting is increased 1%, travel speed increases 1% from 0%.
If setting is increased 1%, travel speed increases 1% from 0%.
A
A
When tire of type 26.5 is installed, select "B"
When tire of type 26.5 is installed, select "B"
(Do not select A which is for setting of tire of type 23.5)
(Do not select A which is for setting of tire of type 23.5)
ADD
ADD
If option is not installed, select "NO ADD"
If option is not installed, select "NO ADD"
NON
NON
When MF lever or right FNR (forward-reverse) switch is
When MF lever or right FNR (forward-reverse) switch is
installed, select "OPT FNR".
installed, select "OPT FNR".
ADD
ADD
Set "ADD" and do not change
Set "ADD" and do not change
ADD
ADD
Set "ADD" and do not change
Set "ADD" and do not change
NO ADD
NO ADD
Set "ADD" and do not change
Set "ADD" and do not change
NO ADD
NO ADD
Set "NO ADD" and do not change
Set "NO ADD" and do not change
NO ADD
NO ADD
Perform following setting according to installation state of
Perform following setting according to installation state of
option and destination
option and destination
･ If option is installed and destination is inside Japan, set
･ If option is installed and destination is inside Japan, set
"HEATER"
"HEATER"
･ If option is installed and destination is outside Japan, set
･ If option is installed and destination is outside Japan, set
"KOHAG"
"KOHAG"
･ If option is not installed, set "NO ADD"
･ If option is not installed, set "NO ADD"
ADD
ADD
Set "ADD" and do not change
Set "ADD" and do not change
ADD
ADD
Set "ADD" and do not change
Set "ADD" and do not change
Others
Others
Selection of options
d t
l
d i
Tools to be used
Name
Q'ty
7
t
t
dj t it ith thi
Facilities to be used
Name
Q'ty
Advertisement
