Advertisement
Available languages
Available languages
Quick Links
H-9645, H-9646
H-9647
MOBILE STAINLESS
STEEL WORKTABLE
TOOL NEEDED
5/32" Allen Wrench
(included)
PAGE 1 OF 9
1-800-295-5510
uline.com
Tabletop x 1
Undershelf x 1
Figure 1
PARTS
ASSEMBLY
1.
With the undershelf on its side, push the legs through
the collars to the desired height. To ensure exact
height, mark desired height on each leg with magic
marker or grease pencil. (See Figure 1)
NOTE: Each leg must be at the same height or
shelf collars could fail. Recommended height
from the floor to the top of the undershelf
is 10" and must be 6" or higher to meet NSF
standards.
NOTE: Casters will add 5/" to overall height.
This additional height should be included when
setting shelf height.
Para Español, vea páginas 4-6.
Pour le français, consulter les pages 7-9.
Set Screw x 16
Caster x 4
Leg x 4
1021 IH-9645
Advertisement
Related Manuals for U-Line H-9647
Summary of Contents for U-Line H-9647
- Page 1 Para Español, vea páginas 4-6. Pour le français, consulter les pages 7-9. H-9645, H-9646 1-800-295-5510 H-9647 uline.com MOBILE STAINLESS STEEL WORKTABLE TOOL NEEDED 5/32" Allen Wrench (included) PARTS Set Screw x 16 Tabletop x 1 Caster x 4 Leg x 4...
- Page 2 ASSEMBLY CONTINUED 2. Secure legs to undershelf with set screws using 5/32" Allen wrench. (See Figure 2) NOTE: Undershelf must be level. Use care not to overtighten screws or failure will occur. Figure 2 3. Flip tabletop over. Insert leg and shelf assembly into tabletop gussets.
- Page 3 ASSEMBLY CONTINUED 6. With caster fully inserted into the leg, turn clockwise Figure 5 until caster is secured to tube leg. (See Figure 5) NOTE: If too loose, pull out caster and tighten further. Repeat step 2. Tube Leg 1-800-295-5510 uline.com PAGE 3 OF 9 1021 IH-9645...
-
Page 4: Herramienta Necesaria
H-9645, H-9646 800-295-5510 H-9647 uline.mx MESA MÓVIL DE TRABAJO DE ACERO INOXIDABLE HERRAMIENTA NECESARIA Llave Allen de 5/32" (incluida) PARTES 16 Tornillos de Ajuste 1 Cubierta 4 Ruedas 4 Patas 1 Repisa Inferior ENSAMBLE 1. Con la repisa inferior de lado, inserte las patas por las ranuras a la altura deseada. - Page 5 CONTINUACIÓN DEL ENSAMBLE 2. Asegure las patas a la repisa inferior con tornillos de ajuste usando una llave Allen de 5/32". (Vea Diagrama 2) NOTA: La repisa inferior debe estar nivelada. Tenga cuidado de no apretar demasiado los tornillos; de lo contrario pueden dañarse. Diagrama 2 3.
- Page 6 CONTINUACIÓN DEL ENSAMBLE 6. Con la rueda completamente dentro de la pata, Diagrama 5 gire en el sentido de las manecillas del reloj hasta que la rueda quede fija en la pata tubular. (Vea Diagrama 5) NOTA: Si queda muy floja, saque la rueda y apriete más.
-
Page 7: Montage
H-9645, H-9646 1-800-295-5510 H-9647 uline.ca TABLE DE TRAVAIL MOBILE EN ACIER INOXYDABLE OUTIL REQUIS Clé Allen de 5/32 po (inclus) PIÈCES Vis de réglage x 16 Surface de table x 1 Roulette x 4 Pied x 4 Tablette inférieure x 1 MONTAGE 1. - Page 8 MONTAGE SUITE 2. Fixez les pieds à la tablette inférieure avec les vis de réglage et la clé Allen de 5/32 po. (Voir Figure 2) REMARQUE : La tablette inférieure doit être nivelée. Faites attention de ne pas trop serrer les vis, sinon une défaillance pourrait se produire.
- Page 9 MONTAGE SUITE 6. Une fois la roulette complètement insérée dans Figure 5 le pied, tournez-la dans le sens horaire jusqu'à ce qu'elle soit bien fixée au pied tubulaire. (Voir Figure 5) REMARQUE : Retirez et resserrez davantage la roulette si elle est instable. Répétez l'étape 2. Pied tubulaire 1-800-295-5510 uline.ca...