Page 2
Indications for Use/Intended Use Symbols on the product The LCD Monitor is intended to provide 4K3D and 2D color video displays of surgical and other Safety sign medical images. Follow the warnings in the instructions for use for parts of the unit on which this Notes symbol appears.
Page 3
IEC 60601-1 standards. If expense. in doubt, consult qualified Sony service You are cautioned that any changes or personnel. modifications not expressly approved in this manual could void your authority to operate this 3.
Page 4
Portable RF communications equipment should be used no closer than 30 cm (12 inches) to any part of the LMD-XH320MT. Otherwise, degradation of the performance of this equipment could result. If the LMD-XH320MT will be used adjacent to or stacked with other equipment, normal operation of the LMD-XH320MT under such configurations should be verified via observation.
Page 5
Guidance and manufacturers declaration electromagnetic immunity The LMD-XH320MT is intended for use in the electromagnetic environment specified below. The customer or the user of the LMD-XH320MT should assure that it is used in such an environment. Compliance level IEC 60601 Electromagnetic environment ...
Page 6
Guidance and manufacturers declaration electromagnetic immunity The LMD-XH320MT is intended for use in the electromagnetic environment specified below. The customer or the user of the LMD-XH320MT should assure that it is used in such an environment. IEC 60601 Compliance Immunity test Electromagnetic environment ...
Page 7
If the measured field strength in the location in which the LMD-XH320MT is used exceeds the applicable RF compliance level above, the LMD-XH320MT should be observed to verify normal operation. If abnormal performance is observed, additional measures may be necessary, such as reorienting or relocating the LMD- XH320MT.
Page 8
The LMD-XH320MT is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. Portable RF communications equipment should be used no closer than 30 cm (12 inches) to any part of the LMD-XH320MT. Otherwise, degradation of the performance of this equipment could result.
Page 9
Top side: 30 cm (11 in.) or more Warning on power connections for medical use Consult with Sony qualified personnel for the Customers in the U.S.A. and Canada should use following types of installation location. the following type of power cord.
Page 10
Product owners are advised to of Sonys limited warranty applicable to this deposit their product at the nearest collection product. point for the recycling of electrical and electronic equipment.
Preset menu .........34 Table of Contents Troubleshooting ..........35 Error Messages ..........35 Specifications ..........36 Precaution ............12 Dimensions ............42 On Safety ...........12 3D Viewing Angle (vertical) ......43 On Installation ...........12 Licenses ............43 Safety precautions for using this unit ..12 Precautions when connecting this unit to medical equipment .........12 To prolong the life of the unit ....12...
When connecting the unit to medical Precaution equipment, refer to “Precautions when connecting this unit to medical equipment”. On Safety Precautions when connecting this unit to medical equipment Operate the unit only with a power source as specified in the “Specifications” section. Before using this unit for medical purposes, be ...
Avoid displaying a still image for an extended Do not connect the power cord and optional period, or using the unit repeatedly in a high Sony AC adaptor (AC-300MD) simultaneously. temperature/high humidity environment such an airtight room, or around the outlet of an air conditioner.
Be sure to use the 3D Glasses supplied with this unit or use the one in the optional accessories SONY WILL NOT BE LIABLE FOR DAMAGES OF explained in this manual. ANY KIND RESULTING FROM A FAILURE TO For the method and cautions of handling the ...
Do not throw away the carton and packing materials. They make an ideal container which to 1) A.I.M.E. is a registered trademark of Sony transport the unit. Corporation. If you have any questions about this unit, contact your authorized Sony dealer.
Page 16
This unit is a high definition and high performance multi-format LCD monitor compatible with the micro-polarizer 3D. Exclusive 3D glasses optimized for this unit are supplied considering long-time work. You can use it for both 2D and 3D with the 2D/3D selection function.
Location and Function of Parts and Controls Front Panel Power indicator When you press PORT A or PORT B when it is lit in white, an image from the input Indicator Operating State connector assigned to the PORT A/B is displayed.
Page 18
CUSTOM buttons Turns on or off the assigned function. You can adjust the assigned function by pressing the / buttons. (Refer to the Custom Button of the System Configuration menu on page 33 and of the Initial Setup menu on page 34.) The following functions are assigned in the default setting.
Rear Panel To use the connectors on the rear panel, remove the cable cover. For details on the cable cover, see page 23. Cable cover (L) cover while pressing the tab at the edge of the When connecting or disconnecting the cable of cover to the right.
Page 21
(4K/HD). SDI 1 and SDI 2 outputs are available. Note 3G-SDI input/output connector (BNC type) Consult with Sony qualified personnel at using this connector. input connector Input connector for serial digital component Caution signals (HD/SD).
Page 22
REMOTE connector (Stereo mini jack) The monitor can be operated partially by An SDI signal is output from the output connecting the optional Foot Switch FS-24. connector only when the monitor is turned on. 12V 2.5A (DC output) connector When the monitor is turned off, the signal is Outputs 12 volts for connected external not output from the output connector.
Note AC input connector Avoid plugging the AC power cord into the AC input connector while connecting the optional Shutter Sony AC adaptor (AC-300MD) to the DC input connector. Make sure that the (On)/ (Standby) switch is set to (Standby).
Page 24
Attach the cable cover (L). AC IN connector Slide the cable cover (L), while sliding the slide locks (2 pcs), which are located at the bottom of the monitor, in the reverse direction of step2. Notes AC power cord After attaching the cable cover (L), check ...
Turning on the Monitor/Switching Input Initial Setting Settings Connect the plug of the AC power cord to an When you turn on the unit for the first time after AC outlet. purchasing it, select the area and language where you intend to use this unit. Press the ...
Using the Menu If you have selected the wrong area, change the Color Temperature setting (page 29). The unit is equipped with an on-screen menu for making various adjustments and settings such To set the using language as picture control, input setting, setting change, You can select one of seven languages (English, etc.
Page 27
About the control navigation Depending on the state, the operation buttons of the unit light as shown below: White light: Operable state. Green light: Operating state. Off: Unable to operate. Press the / button to select the tab. The selected tab is shown in blue, and setting items of the selected tab appear.
Pattern Skip Adjustment Using the Menus Input/Output Configuration (page 31) Clone Out Items Port A Input Select Port B Input Select The screen menu of this monitor consists of the Input Name following items. AUX IN Setting Power Supply Color Tone Adjustment (page 28) System Configuration (page 32) Gamma Phase...
Menu Setting Menu Setting Mono Sets the display to a monochrome Gamma Select the appropriate gamma mode picture. Set to “On” for a monochrome from “1.8,” “2.0,” “2.2,” “2.4,” “2.6,” picture, set to “Off” for a normal “DICOM,” “Highlight,” “HLG,” or “Auto.” (chromatic) picture.
To display the corresponding signal images are always displayed in 2D. with “Enhanced Format,” use a Premium High-Speed HDMI cable within a length of 3 meters (Sony Notes product recommended). For the 4K equivalent signal, signals of the Dual Stream system are not displayed.
Menu Setting Menu Setting Port C Input Sets the input connector for the third Color Space Select the color gamut from “Auto,” screen. “BT.709,” or “BT.2020.” Select from among “12G-SDI 1,” “12G- When “Auto” is selected, the color SDI 2,” “3G-SDI,” “Display Port,” gamut changes according to the “HDMI,”...
Menu Setting Menu Setting Input Name Set the name of the 12G-SDI 1, 12G-SDI Input Connector Name 2, 3G-SDI, Display Port, HDMI, DVI-D input connector. Select Port Endoscope Control Lock Laparoscope Ultrasound Recorder Signal Format Printer ...
Page 33
Menu Setting Menu Setting A.I.M.E. Display Remote Always displayed while the A.I.M.E. Remote Mode Sets the remote function when the function is activated. REMOTE connector is connected to the Off: optional Foot Switch FS-24. Not displayed. Off: Inactivates the remote function.
Menu Setting Menu Setting Backlight Control Off: Port B Input Select Sets the input connector that is Turns off backlight control. skipped when changing the input Standard: signal by pressing the PORT B button. Sets the backlight to standard Set to “Not Skip”...
When the following messages appear on the problem and as a result, eliminate the need to screen, turn off the power and contact an contact technical support. authorized Sony dealer. “Unknown” or “Out Of Range” is displayed. Input the supported signal (page 39).
Output Specifications 3G-SDI output connector BNC type (1) Active-through Picture performance 12G-SDI 1/2 output connector BNC type (2) LCD panel TFT Active Matrix Active-through Pixel efficiency CLONE OUT connector 99.99% BNC type (1) Viewing angle (panel specification) DC 5V OUT Round type pin (female) (1) 89°/89°/89°/89°...
Page 37
PERIOD OR AFTER EXPIRATION OF THE Shield Cover WARRANTY, OR FOR ANY OTHER REASON CFV-50SC WHATSOEVER. SONY WILL NOT BE LIABLE FOR CLAIMS OF Caution ANY KIND MADE BY USERS OF THIS UNIT OR AC-300MD does not conform to the drip-proof ...
Page 38
Pin assignment 12V 2.5A (DC output) connector SERIAL REMOTE (RS-232C) connector D-sub 9-pin, female Pin number Signal Pin number Signal 12 V REMOTE (stereo mini jack) connector Pin number Signal On (short to sleeve) Off (open) 5V 2.0A (DC output) connector Pin number Signal...
Page 39
Available signal formats The unit is compatible with the signal systems shown below: Signal format 12G-SDI 1 12G-SDI 2 3G-SDI SDI Single Link SD-SDI 720×487/59.94i 4 : 2 : 2 YCbCr 10bit × × 720×576/50i 4 : 2 : 2 YCbCr 10bit ×...
Warning Dimensions Be sure to set the tightening torque value to the following value. Torque value: 1.2±0.1 N·m Front Make sure the tightening torque value is at this When an optional stand SU-600MD is attached value. If the torque value is not appropriate, the mounting part may become damaged or the screws may become loosened, and in the worst case, it may cause injury or damage to the unit...
3D Viewing Angle (vertical) Licenses For details on the license, refer to “Software License Information” on the CD-ROM. Side View 3D Viewing Angle (vertical) Crosstalk ratio ≤ 7% A (Typical) B (Typical) C (Typical) 690 mm 32° 1 380 mm...