Adjusting Speaker Output Level; Adjusting The Sound Parameters For The Surround/Dsp Modes - JVC RX-E51BEB Instructions Manual

Adjusting speaker output level

• SUBWFR LVL (subwoofer output level),
• FRONT L LVL (left front speaker output level),
• FRONT R LVL (right front speaker output level),
• CENTER LVL (center speaker output level),
• SURR L LVL (left surround speaker output level),
• SURR R LVL (right surround speaker output level)
You can adjust the speaker output levels.
Adjust all the speakers' output levels so that you can listen sounds
from all speakers at the same level.
• Once you have made an adjustment, it is memorized for each
source.
Adjustable range: –10 (dB) to +10 (dB) (in 1 step intervals)
Initial setting: 0 (dB) for all speakers
NOTES
• If you have selected "NO" for a speaker (see page 16), the
output level for the corresponding speaker is not adjustable.
• While using headphones, you can adjust only the left and right
front speakers' output level.
• If you change one of these settings (except the subwoofer
output level) manually, the distance and output levels set by
Smart Surround Setup will be cleared and those manually set
will be effective.
From the remote control:
1
Press TEST TONE to check the speakers' output
balance.
"TEST L" starts flashing on the display, and a test tone
comes out of the speakers in the following order:
EQ C.TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS TUNED ST
LPCM L C R PL
DOLBY D NEO : 6
S . WFR LFE
DTS AAC DSP 3D
LS SB RS
96 / 24 AUTO SR
L
(Left front speaker) (Center speaker)
SW LS
(Subwoofer) (Left surround speaker)
2
Adjust the speaker output levels.
To adjust the left front speaker level,
press FRONT L +/–.
To adjust the right front speaker level,
press FRONT R +/–.
To adjust the center speaker level,
press CENTER +/–.
To adjust the left surround speaker level,
press SURR L +/–.
To adjust the right surround speaker level,
press SURR R +/–.
To adjust the subwoofer level,
press SUBWFR +/–.
3
Press TEST TONE again to stop the test tone.
NOTES
• You can adjust the speaker output levels without the test
tone.
• No test tone is available when the HEADPHONE (or 3D
HEADPHONE) mode is in use.
AUTO MUTING SLEEP AUTO MODE
ATT
HP
MHz
kHz
C R
(Right front speaker)
RS
(Right surround speaker)
Adjusting the sound parameters for
the Surround/DSP modes
You can adjust the Surround/DSP sound parameters to your
preference.
• For details about the Surround/DSP modes, see pages 29 to 33.
Adjusting the effect level for DSP modes—EFFECT
This setting is available only when one of the DSP modes (except
ALL CH ST.) is in use. To activate DSP mode, see pages 32 and
33.
• Once you have made an adjustment, it is memorized for each
DSP mode.
Adjustable range: 1 to 5 (in 1 step intervals)
Initial setting: EFFECT 3
As the number increases, the effect becomes stronger.
Normally, select "3."
Adjusting the panorama control for Pro Logic II
Music—PANORAMA
This setting is available only when Pro Logic II Music is in use. To
activate Pro Logic II Music, see pages 32 and 33.
• Once you have made an adjustment, it is memorized until you
change the setting.
• You cannot use the remote control for this setting.
PANORAMA ON Select to add "wraparound" sound effect with
side-wall image.
PANORAMAOFF Select to listen to originally recorded sound.
Initial setting: PANORAMAOFF
Adjusting the center tone—CENTER TONE
This setting is available when one of the Surround/DSP modes is
in use.
• If you have set "CENTER SPK" to "NO" (see page 16), the
center tone is not adjustable.
• This setting is common to all Surround modes, and is
memorized separately for DSP modes.
Adjustable range: 1 to 5 (in 1 step intervals)
Initial setting: CNT TONE 3
As the number increases, the dialogue becomes stronger.
Normally, select "3."
• When the center tone is set to other than "CNT TONE 3," the
C.TONE indicator lights up on the display.
From the remote control:
To adjust the effect level:
Press SOUND, then press EFFECT
repeatedly.
To adjust the center tone:
Press SOUND, then press C.TONE
repeatedly.
NOTE
After pressing SOUND, the numeric
buttons work for sound adjustments. To
use the numeric buttons to operate your
target source, press the corresponding
source selecting button before operation;
otherwise, the remote control may not
work as you intend.
21