Adjusting The Speaker Channel Output Levels-Level; Adjusting The Parametric Equalizer-Parametric Eq - JVC RX-DP10VBK Instructions Manual

Adjusting the Speaker Channel Output
Levels—LEVEL (1)
LEVEL
TEST TONE :OFF
FRONT L LEVEL: 0dB
CENTER LEVEL : 0dB
FRONT R LEVEL: 0dB
SURR R LEVEL : 0dB
SBACK R LEVEL: 0dB
SBACK L LEVEL: 0dB
SURR L LEVEL : 0dB
SUBWOOFER : 0dB
:OPERATE :BACK
Notes:
• The speaker level adjustments except the left/right front level and
subwoofer level will be affected and be changed according to the
Surround/DSP mode setting.
• You can show this submenu simply by pressing TEST button on the
remote control. Test tone comes out of the activated speakers in
sequence. (See page 49.)
7 Adjustment procedure on this submenu
Adjustment is also possible without outputting the test tone. In this
case, you can skip steps 1, 2 and 6 below.
Press fi or % (DOWN or UP) to select "TEST TONE."
1
Press # or @ (RIGHT or LEFT) to output the test tone.
2
(See "Outputting the test tone" below.)
Press fi or % (DOWN or UP) to select a speaker you want
3
to adjust.
Press # or @ (RIGHT or LEFT) to adjust the speaker
4
output level.
5
Repeat step 3 and 4 to adjust the other speaker output levels.
6 After adjustment is finished, stop the test tone.
1 Press % or fi (UP or DOWN) to select "TEST TONE."
2 Press # or @ (RIGHT or LEFT) to select "OFF."
7 Outputting the test tone
CAUTION:
Test tone is automatically fixed to 0 dB, but this level will be
louder than you would expect.
Select one of the following.
• Test tone will be heard about three seconds after you select
"AUTO" or "MANUAL."
AUTO : When this is selected, the test tone comes out of all
the activated speakers in sequence (for 2 seconds
each). The test tone comes out of the activated
speakers in the following sequence:
Left front speaker = Center speaker = Right front speaker
= Right surround speaker = Right surround back speaker
= Left surround back speaker = Left surround speaker
= Subwoofer = (Back to the beginning)
MANUAL : When this is selected, the test tone comes out of
only the speaker you select. (To select the speaker,
see the right column.)
OFF : Select this to stop the test tone.
On this submenu, you can adjust
the speaker channel output levels.
While outputting the test tone,
select a speaker channel and
adjust its output level.
Once adjustment is done on this
submenu, it is stored for each
source when you change the
source or when you turn off the
receiver.
Notes:
• "TEST TONE" is not available if both speakers 1 and 2 are
deactivated or if Surround mode is turned off.
• If "NO" or "NONE" is selected for a speaker on the SPEAKER
SETTING submenu (page 36), test tone does not come out of
the speaker.
7 Adjusting the speaker channel output levels
Select and adjust the following speakers:
FRONT L LEVEL : Select this to adjust the left front
speaker output level within the range
of –20 dB to +10 dB, and – – – dB
(no sound).
FRONT R LEVEL : Select this to adjust the right front
speaker output level within the range of
–20 dB to +10 dB, and – – – dB (no
sound).
CENTER LEVEL : Select this to adjust the center speaker
output level within the range of –10
dB to +10 dB.
SURR L LEVEL : Select this to adjust the left surround
speaker output level within the range
of –10 dB to +10 dB.
SURR R LEVEL : Select this to adjust the right surround
speaker output level within the range
of –10 dB to +10 dB.
SBACK L LEVEL : Select this to adjust the left surround
back speaker output level within the
range of –10 dB to +10 dB.
SBACK R LEVEL : Select this to adjust the right surround
back speaker output level within the
range of –10 dB to +10 dB.
SUBWOOFER : Select this to adjust the subwoofer
output level within the range of –10
dB to +10 dB.
Note:
If "NO" or "NONE" is selected for a speaker on the SPEAKER
SETTING submenu (page 36), you cannot adjust its output level.
Adjusting the Parametric Equalizer
—PARAMETRIC EQ (2)
PARAMETRIC EQ
FRONT
CENTER
SURROUND
SURROUND BACK
:ENTER
:BACK
Notes:
• This function is applied only to the main room sources.
• If "NO" or "NONE" is selected for a speaker on the SPEAKER
SETTING submenu (see page 36), you cannot select the
corresponding channel.
• If THX Surround or DVD MULTI playback mode is in use, this
submenu is not available.
On this submenu, you can
adjust equalization patterns
according to your preference.
First, select the signal channel
(speaker) you want to adjust,
then move to its adjustment
screen.
Continued on the next page.
44