Panasonic AW-HE145WP Operating Instructions Manual page 86

Web screen configurations (continued)
HDMI
Make the settings for output from the HDMI connector.
Format
Set the output format.
The following format settings are possible depending on the [Format]
setting in the [System] screen.
Frequency System Format
59.94Hz 1080/59.94p
1080/59.94i
1080/29.97p
1080/29.97PsF
1080/23.98p(59.94i)
720/59.94p
50Hz 1080/50p
1080/50i
1080/25p
1080/25PsF
720/50p
24Hz 1080/24p
23.98Hz 1080/23.98p
1080/23.98PsF
* 1
It denotes "1080/23.98p over 59.94i".
*
2
It denotes "1080/23.98p over 59.94p".
Factory settings: 1080/59.94p (AW-HE145WP/AW-HE145KP)
1080/50p (AW-HE145WE/AW-HE145KE)
HDR Output Select [SDR, HDR(2020), HDR(709)]
Select the signal to be output when [Gamma Mode] is [HLG].
SDR SDR output
HDR(2020) HDR output (BT.2020 equivalent color gamut)
HDR(709) HDR output (BT.709 equivalent color gamut)
Factory settings: HDR(2020)
<NOTE>
• [HDR Output Select] cannot be changed when [Gamma Mode] is
other than [HLG]. (→ page 105)
Format (HDMI)
1080/59.94p
1080/59.94i
1080/29.97p
1080/29.97p
1080/23.98p(59.94p)
1 2
* *
720/59.94p
1080/50p
1080/50i
1080/25p
1080/25p
720/50p
1080/24p
1080/23.98p
1080/23.98p
Bar [Camera, Colorbar]
Switch between camera images and color bars.
Camera Camera images
Colorbar Color bar
Factory settings: Camera
Color Bar Type [Type1, Type2]
Select the type of color bar to display.
Type1:
This is only enabled when [Bar] is set to [Colorbar].
Factory settings: Type2
<NOTE>
• Even if the [HDR Output Select] for each of the outputs is either
[HDR(2020)] or [HDR(709)], the color bar for SDR is output.
Tone [Off, Low, Normal]
Make the settings for the test tone signal (1 kHz) output while the
color bar is displayed.
Off Test tone is not output.
Low Test tone is output at low volume.
Normal Test tone is output at normal volume.
This is only enabled when [Bar] is set to [Colorbar].
Factory settings: Normal
OSD Mix
Select whether to turn off/on camera menu, status, and other displays
for each output image.
3G SDI [Off, On ]
*
HDMI [Off, On ]
*
IP [Off, On ]
*
Off The camera menus and statuses are not displayed on the
output pictures covered by the setting items listed above.
On The camera menus and statuses are displayed for the output
pictures covered by the setting items listed above.
: Factory settings
*
<NOTE>
• When this is set to [Off], the camera menu can be displayed for
about 1 minute after the unit is turned on.
OSD Off With R‑Tally [Off, On]
Off or on the function that turns off camera menu, status, and other
displays when red tally signals are received via commands or
contacts.
When the red tally signal releases, the camera menu display will
return.
Factory settings: Off
OSD Status [Off, On]
Turn the status display during AWB and ABB off/on, or error display
when an error occurs.
Factory settings: Off
86
Type2: