Panasonic AW-HE145WP Operating Instructions Manual page 17

Parts and their functions (continued)
14.
G/L IN connector <G/L IN>
This is the external sync signal input connector.
This unit supports BBS (Black Burst Sync) and tri-level
synchronization.
Supply to this connector the signals that correspond to the video
signal format which has been set.
Frequency: 59.94 Hz, 29.97 Hz
External sync signal input format
Format
1080/59.94p 1080/59.94p
720/59.94p
1080/59.94i ―
1080/29.97p ―
1080/29.97PsF ―
1080/23.98p ―
over 59.94i
720/59.94p 1080/59.94p
720/59.94p
Frequency: 50 Hz, 25 Hz
External sync signal input format
Format
1080/50p 1080/50p
720/50p
1080/50i ―
1080/25p ―
1080/25PsF ―
720/50p 1080/50p
720/50p
Frequency: 24 Hz
External sync signal input format
Format
1080/24p 1080/24p
1080/24PsF
Frequency: 23.98 Hz
External sync signal input format
Format
1080/23.98p 1080/23.98p
1080/23.98PsF
1080/23.98PsF
15.
DC IN connector <12 V
Input 12 V DC.
<NOTE>
• Use a DC cable with the following lengths.
For 12 V input: Max. 3 m (9.84 ft) (when using an AWG16 cable)
„ External DC power supply
Connect after making sure that the output voltage of the external DC
power supply is compatible with the rated voltage of the camera.
Select an output amperage for the external DC power supply with a
margin above the total amperage of the connected devices.
The total amperage of connected devices can be calculated with the
following formula.
Total power consumption ÷ voltage
When the power of the camera is turned on, inrush current is generated.
Insufficient power supply when turning on the power may cause a
malfunction. We recommend that you use an external DC power supply
that can assure double the capacity of the total power consumption of the
camera and connected devices that are turned on by interlock when the
power of the camera is turned on (such as lenses, wireless microphone
receivers).
Tri‑level sync BBS
1080/29.97p 480/59.94i
1080/59.94i
1080/29.97PsF
Tri‑level sync BBS
1080/25p 576/50i
1080/50i
1080/25PsF
Tri‑level sync
Tri‑level sync
IN> (XLR connector)
• Make sure of the pin alignment of the DC output terminal of the
external DC power supply and the camera DC IN connector, and
connect the polarity correctly.
If the +12 V power supply is mistakenly connected to the GND terminal,
it may cause fire or malfunction.
1 GND
2
3
1
4
3
2
4 +12 V
16.
IR ID switches <IR ID>
CAM1 CAM2
These are used to select the ID of the wireless remote control
(optional accessory). (→ page 25)
The IR ID switch settings "CAM1" to "CAM4" correspond to the
CAMERA buttons <1> to <4> on the wireless remote control.
17.
Ground connector
Connects to the ground connector on a wall outlet, ground bar, etc.
for grounding. (→ page 6)
18.
AUDIO IN connector <AUDIO IN>
Inputs external audio (microphone, line).
19.
Ventilation holes
Blocking the ventilation holes may cause a malfunction. Make sure
there is sufficient space around the ventilation holes.
20.
Tripod screw holes
(Screw: 1/4-20 UNC, ISO 1222 [6.35 mm (1/4 inches)])
Use these screw holes when securing the unit to a tripod, etc.
17
12 V IN
—
—
HA16RA-4P (77)
Hirose Electric Co.
CAM3 CAM4