Setting/Releasing The Limiters; Basic Limiter Operations; Setting The Limiters; Releasing The Limiters - Panasonic AW-HE145WP Operating Instructions Manual

Setting/releasing the limiters

Basic limiter operations

1.
Press the <MENU> button.
Tap the button (rather than pressing it). When it is pressed for 2
seconds, the camera menu will appear.
If this happens, press the <MENU> button again for 2 seconds to
clear the camera menu.
1
Then start again from step .
2.
Press the <4 / 5/ b / a> button for 2 seconds while
holding down the <PRESET> button.
The limiter for the upper limit, lower limit, left limit or right limit is set
(or released) using these direction buttons, respectively. The tally
lamp will blink at this time. When a limiter is set, it blinks once; when a
limiter is released, it blinks twice.
If any other button was operated between steps
1
from step .

Setting the limiters

The limiter positions can be set by following the steps below.
When the position is set, the tally lamp blinks once.
1.
Press one of the CAMERA buttons <1> to <4> to select
the unit.
• Setting the upper limit position of the movement range
Press the <4> or <5> button of the wireless remote control to
turn the unit as far as the position which will serve as the upper
limit.
Next, perform the steps in "Basic limiter operations".
(Press the <MENU> button quickly and then press the <4>
button for 2 seconds while holding down the <PRESET>
button.)
• Setting the lower limit position of the movement range
Press the <4> or <5> button of the wireless remote control to
turn the unit as far as the position which will serve as the lower
limit.
Next, perform the steps in "Basic limiter operations".
(Press the <MENU> button quickly and then press the <5>
button for 2 seconds while holding down the <PRESET>
button.)
• Setting the left‑most limit position of the movement range
Press the < b > or < a > button of the wireless remote control
to turn the unit as far as the position which will serve as the
left-most limit.
Next, perform the steps in "Basic limiter operations".
(Press the <MENU> button quickly and then press the
< b > button for 2 seconds while holding down the <PRESET>
button.)
• Setting the right‑most limit position of the movement range
Press the < b > or < a > button of the wireless remote control
to turn the unit as far as the position which will serve as the
right-most limit.
Next, perform the steps in "Basic limiter operations".
(Press the <MENU> button quickly and then press the
< a > button for 2 seconds while holding down the <PRESET>
button.)

Releasing the limiters

The limiter positions that are set can be released by following the steps
below.
When the position is released, the tally lamp blinks twice.
1.
Press one of the CAMERA buttons <1> to <4> to select
the unit.
2.
Release the limiters by taking the steps below.
• Releasing the upper limit position of the movement range
1 2
and , start again
• Releasing the lower limit position of the movement range
• Releasing the left‑most limit position of the movement range
• Releasing the right‑most limit position of the movement range

Resetting the limiters

To reset the limiters, the currently established settings must be released.
The limiter positions that are set can be reset by following the steps
below.
1.
Release the settings of the limiter positions to be reset
by following the steps in "Releasing the limiters".
2. Set the limiter positions by following the steps in
"Setting the limiters".
138
Perform the steps in "Basic limiter operations".
(Press the <MENU> button quickly and then press the <4>
button for 2 seconds while holding down the <PRESET>
button.)
Perform the steps in "Basic limiter operations".
(Press the <MENU> button quickly and then press the <5>
button for 2 seconds while holding down the <PRESET>
button.)
Perform the steps in "Basic limiter operations".
(Press the <MENU> button quickly and then press the
< b > button for 2 seconds while holding down the <PRESET>
button.)
Perform the steps in "Basic limiter operations".
(Press the <MENU> button quickly and then press the
< a > button for 2 seconds while holding down the <PRESET>
button.)